Advertisement
®
Assembly Instructions for Work Stand RTL01
Tools Required:
Pair of pliers or 7/16" wrench, Phillips head screw driver, drill and a 1/8" drill bit.
Parts List:
A) Lower Cross Brace
B) Lower Cross Brace
C) Upper Cross Brace (Pierced)
D) Upper Cross Brace (Pierced)
E) Legs
F) Height Extension
G) Carriage Bolts
H) Lock Washers
IMPORTANT - PLEASE READ COMPLETE ASSEMBLY INSTRUCTIONS BEFORE YOU START.
plied - check with your local Building Supply or Hardware Store for
proper fasteners for your particular type of floor.
Freud America, Inc.
Qty.
Parts List:
2
I) Nuts
2
J) Rubber Leveling Feet
2
K) Corner Braces
2
4
4
44
I
44
Step 1
Prepare two leg assemblies by
attaching Lower Cross Brace (A) to a
pair of Legs (E). Insert Carriage Bolt
(G) through single square hole in
Leg (E) and round hole in Lower
Cross Brace (A). Add Lock Washer
(H) and Nut (I). Repeat on other side.
Do not tighten bolts at this time.
Step 3
Attach Upper Cross Brace (D) to Leg
Assembly (E). Note: If a lower shelf is
desired it should be cut and installed
before the lower Cross Braces (B) are
attached. Shelf size approximately
21-1/2" x 23-1/2" (54.6 cm x 59.7 cm).
Attached Lower Cross Brace (B) to
Leg Assembly (E). Repeat on other
side. Tighten all Bolts.
Step 5
Note: For added stability and safety,
you may choose to fasten your work
stand to the floor, particularly when
using large heavy tools such as drill
presses, table saws, and radial arm
saws. First, remove the rubber level-
ing feet installed in step 4 of these
instructions. Position work stand at
the desired location and mark hole
position on the floor for installation of
the required type of floor fasteners.
Note: Floor fasteners are not sup-
Qty.
44
4
2
G
H
feet (F). Once the feet are at the desired position they can be locked in place
by turning the nut attached to the feet clockwise until tight. Place the stand in
the upright position and check for level. If the stand is not level adjust the rub-
ber leveling feet until the table is properly adjusted
on the stand, insert the No. 10 x 3/4" screws (packaged separatley)
through the mounting holes and into the pilot holes and tighten with a
Phillips screwdriver. For use with your bench top tool a wood platform
20" x 24" must be bolted on Upper Cross Braces (platform and hard-
ware not included). Secure tools to wood platform.
1-800-472-7307
A
B
C
D
F
K
J
Step 2
Attach Upper Cross Brace (C) to a
pair of Legs (E). Insert two (2)
Carriage Bolts (G) through upper
square holes in Leg (E) and round
holes in Upper Cross Brace (C). Add
Lock Washers (H) and Nuts (I).
Repeat on other side. Do not tighten
bolts at this time.
Step 4
Turn unit upside down. Install corner
braces (K) in opposing corners of the
table with Bolts (G), Lock Washers (H),
and Nuts (I). Note: The table top height
can be adjusted from 32" to 38" by mov-
ing the Height Exstensions (F) up or
down on Leg (E). Tighten nuts and bolts.
After all 4 legs are tightened, you may
choose to install the 4 Rubber Leveling
Feet (J) included in the kit. To install the
leveling feet simply screw the feet into
the nut welded to the inside of the table's
Step 6
The RTL01 Tool Stand is intended for
use with the Freud Router Table Top
or it can accommodate most bench
top tools.To mount the Freud Router
Table Top center the top on the stand
and mark the mounting hole loca-
tions. Ensure that none of the holes
are aligned with the aluminum track
or the threaded inserts of the Router
Table Top. Remove the top and drill a
1/8" X 5/8" deep pilot hole in the cen-
ter of each mark. Reposition the top
www.freudtools.com
E
Advertisement
