Rear Panel Features - Sunfire Bob carver's Ultimate receiver User Manual

CHAPTER 1
Rear Panel Fea tures
MANUFACTURED UNDER LICENSE
FROM DOLBY LABORATORIES.
AUDIO/VIDEO INPUTS
"DOLBY", "PRO-LOGIC" AND THE
DOUBLE-D SYMBOL ARE
TRADEMARKS OF DOLBY DVD SAT VID1
S
LABORATORIES.
VIDEO
8
FM
75
COMP DVD SAT VID1
VIDEO
GND
9
DVD SAT VID1
L
AM
R
MANUFACTURED UNDER LICENSE
FROM DIGITAL THEATER SYSTEMS,
INC. US PAT. NO. 5,451,942,
5,956,674, 5,974,380, 5,978,762 AND
AUDIO INPUTS
OTHER WORLD-WIDE PATENTS
ISSUED AND PENDING. "DTS", PHONO DAT TAPE
"DTS-ES EXTENDED SURROUND"
AND "NEO:6" ARE TRADEMARKS
OF DIGITAL THEATER SYSTEMS,
INC. COPYRIGHT 1996, 2000, L
DIGITAL THEATER SYSTEMS, INC.
ALL RIGHTS RESERVED.
10
R
PHONO DAT TAPE
11
1. Audio/Video Inputs
These audio, composite-video
and S-video inputs con nect to the
outputs of your audio video com-
po nents. When these inputs are
selected, the audio will be heard
in your system and the video will
be seen on the TV screen. VID2
can be used for a second VCR.
2. Audio/Video Outputs
MAIN: connects to the inputs of a
TV monitor, where the video
of any selected input and the
On Screen Display (OSD) can
be viewed. The audio con nec -
tions allow you to listen to any
selected audio source through
your TV's speak ers.
VCR: connects to the inputs of a
VCR to allow recording.
VID2/MON2: connects to the input
of a second VCR for recording,
or to a second TV. When con-
Þ gured in the OSD for "VID2,"
this output is muted whenever
the VID2 input is selected. This
prevents feedback; also there
is no OSD then on this output.
When conÞ gured for "MON2,"
the output is always active, the
same as the Main output.
12
1 2
AUDIO/VIDEO OUTPUTS
VID2 VCR CD MAIN VCR VID2/MON2
VID2 VCR CD MAIN VCR VID2/MON2
VID2 VCR CD MAIN VCR VID2/MON2
L
R
AUDIO OUTPUTS 8-CHANNEL INPUTS
DAT TAPE LEFT L SUR CEN LB SUR
L
R
DAT TAPE
RIGHT R SUR SUB RB SUR
12 13
3. Component Video In
4. Component Video Out
3 4
Made in Snohomish, Washington, U.S.A.
COMPONENT VIDEO IN COMPONENT
OUT
DVD SAT VID1 MAIN MON2
Y
C
r
C
b
DIGITAL AUDIO INPUTS
DVD SAT
DVD SAT VID1 CD
CD DAT
STEREO OUTPUTS LINE LEVEL AUDIO OUTPUTS
FIXED MAIN ZONE2 LEFT LEFT SUR
L
R
FIXED MAIN ZONE2
RIGHT RIGHT SUR
14 15
Note: Analog audio signals are
present at these L and R outputs
even if a digital input has been
selected. The output is a 2 chan-
nel downmix if the digital source is
more than 2 channels.
These inputs con nect to the
component video outputs of your
DVD, SAT or other video source
(VID1) if they have this advanced
capability. When these inputs are
se lect ed, the Receiver's Pro-
ces sor will au to mat i cal ly route
any video signals going into these
jacks to the component video
outputs. Note that component
video provides the best picture
compared to composite or
S-video. The Receiver can also
switch HDTV signals.
If your TV Monitor has component
video inputs, connect them to
these outputs. If you select DVD,
SAT or VID1, then any video sig-
nals going to the component
inputs, will pass through to your
TV monitor. Note that the OSD is
not available from the component
video outputs.
5 6
RIGHT RIGHT
TRIGGERS SURROUND MAIN
12VDC
SPEAKER LEVEL AUDIO OUTPUTS
Sunfire
VID1 Ultimate Receiver
DIGITAL OUT IEEE
1394
VID2
SIDES I R
CENTER SUB2 LB SUR L SIDE AXIS
MAIN
R SIDE AXIS ZONE2
SUB1 SUB3 RB SUR
16 17 18 19 20
5. Triggers and Relay
The relay switch is normally open,
and it will close after a short delay,
when selecting a source. This can
be used in in stal la tions to trigger
video screen deployment, or other
custom purposes. The OSD
INPUTS menu lets you choose
which inputs activate the relay.
The +12 VDC outputs are on
whenever their zone is enabled.
They can be used to automatically
turn on ampliÞ ers for example.
The 1/8" mini-jack is wired in
parallel with the terminals. Do not
exceed a current draw of 500mA
total for both outputs.
6. Speaker-level Outputs
These speaker-level audio out-
puts connect to the inputs of your
speakers. The outputs are: front
left, front right, center, left sur-
round, and right surround. The
two lower (Aux) outputs can be
assigned as surround back out-
puts, Zone 2 outputs or side-axis
outputs, see page 41 for details.
7
LEFT LEFT
CENTER MAIN SURROUND
SURROUND
RIGHT BACK LEFT
RS-232
OPTIONAL:
SIDE-AXIS
OR
ZONE2
REPLACE WITH ORIGINAL AC INPUT
FUSE TYPE AND RATING
AC FUSE
120 VAC 60 Hz
21
User's Manual