Packing List; Operating The Handle Assembly; Assembling The Spray Wand; Installing The Rotating Brush - Craftsman 138.75275 Operator's Manual

V.,T;T.,'.] =1 _N -']nt'd
PACKING LIST
Pressure washer with 25 ft. high pressure hose
Operator's manual
Metal spray gun
4 auick connect nozzles (stream, narrow fan,
wide fan and soap)
Bonus turbo nozzle
Bonus rotating brush
WA R N I N G ! If any parts are damaged
or missing do not operate this product until
the parts are replaced. Use of this product
with damaged or missing parts could result in
serious personal injury.
_,
WAR N I N G ! Do not attempt to modify
this product or create accessories not
recommended for use with this product. Any
such alteration or modification is misuse and
could result in a hazardous condition leading to
possible serious personal injury.
TO TRIGGER HANDLE (See Figure 5.)
• Slide the hose lock forward to open.
Connect the high pressure hose to the trigger
handle. Insert 1Sighpressure hose into trigger
handle.
CONNECTING THE GARDEN HOSE
(See Figure 6.)
_, CAUTION:
Always observe all local regulations when
connecting hoses to the water main. Some
areas have restrictions against connecting
directly to public drinking water supply to
prevent the feedback of chemicals into the
drinking water supply. Direct connection through
a receiver tank or backfiow preventer is usually
permitted.
Connect garden hose to pressure washer water
intake.
• Uncoil the garden hose from the storage reel.
NOTE: There must be a minimum of 10 feet of unre-
stricted garden hose between the water intake and
the garden hose faucet or shut off valve (such as a "Y"
shut off connector).
• Run water through the garden hose for 30
seconds to clean any debris from the hose.
• Inspect the screen in the water intake.
,_ WAR N I N G ! Do not connect to power
supply until assembly is complete. Failure to
comply could result in accidental starting and
possible serious personal injury.
OPERATING THE HANDLE ASSEMBLY
(See Figure 3.)
• Open for use: Lift up on the handle bar
pivoting it towards the back into an upright
position until it clicks and locks into place.
• Pull the release button on the handle
assembly out sideways and lift up the
handle until it clicks into place.
• To fold the handle pull the latch sideways
again, and push the hand e down.
ASSEMBLING THE SPRAY WAND
(See Figure 4.)
• Push the end of the spray wand into the
trigger handle and rotate clockwise to
secure.
• Pull on the spray wand to be certain it is
properly secured.
• Place the assembled spray wand in the
spray wand holder.
CONNECTING HIGH PRESSURE HOSE
INSTALLING THE ROTATING BRUSH
• Turn off the pressure washer and shut off the
water supply. Pull trigger to release pressure.
• Engage the lock-out on the trigger handle by
pusmng the trigger lock button to,he right.
• To assemble the rotating brush insert the brush
wand nto the pressure washer wand, and tw st.
Applications: Ideal for cleaning most smooth
surfaces including vehicles, boats, outdoor
furn ture, fabr cs, past cs, fberg ass, g ass, and
windows.
,_ WAR N I N G ! To reduce the risk of injury,
user must read and understand the operator's
manual for this pressure washer and this
accessory. Wear eye protection marked to .
comp=y w=th Z87.1. Ensure compatiDi=ity ana
fit before using this accessory. Turn off the
pressure wasSer before changing or adjusting
accessories. For cold water use only. Do not
use this accessory if damaged or if a part is
missing. Dirt and debris can damage delicate
surfaces. Thoroughly rinse the brush before use
and continue to do so at regular intervals during
use. Thoroughly clean thebrush after use. Allow
to dry and always store brush without bending
the bristles. Save these instructions. Refer to
them frequently and use them to instruct other
users. Ifyou loan someone this tool, loan them
these instructions also.
9-English