Preset For Use; To Add/Delete Channels; Clock Setup - Emerson EWV603 Owner's Manual

3. Preset for Use

Turn on the VCR for the first time
1
1
Turn on the TV and set
it to channel 3.
• If channel 3 is already occupied for broad-
casting, see"RF Output Channel" section.
2
2
POWER Remote Control TV Screen
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
or
3
3
CH 01
AUTO SET UP
Do you connect the cable of the cable box or
the satellite box to the VCR's ANT IN jack?
Yes
Y es
Y es
Press the MENU
button to exit
• Refer to "Hint for Cable Box or
Satellite Box" section on page 1.
No
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memorized
in VCR by using the CHANNEL buttons.
• If "AUTO SET UP" appears on the TV screen
again, check the cable connections. Then,
press the F.FWD button once again.
Hint
Hint
• Repeat these steps only if there was a
power failure or if the VCR has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by directly
pressing the Number buttons on the
remote control.
Notes for using the Number but-
tons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit
channel numbers with a zero (For
example: 02, 03, 04 and so on).
To Preset the Channel Again
1) Press the MENU button until the main
menu appears.
2) Select "CHANNEL SET UP" by pressing the
PLAY or STOP button. Then, press the
F.FWD button.
3) Select "AUTO SET UP" by pressing the
PLAY or STOP button. Then, press the
F.FWD button. After scanning, the tuner
stops on the lowest memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main
menu appears.
2) Select "LANGUAGE SELECT" by pressing
the PLAY or STOP button. Then, press the
F.FWD button.
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing the PLAY or STOP
button. Then, press the C.RESET/EXIT but-
ton.
Hint
Hint
• If you accidentally select Spanish or French
and need English: Press the MENU button
and choose SELEC. IDIOMA, or SELEC-
TION LANGUE. Press the F.FWD button,
and select ENGLISH. Finally, press the
C.RESET/EXIT button.

To Add/Delete Channels

1
1
MENU
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
or
2 2
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
or
3
3
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
or
Select the channel to be
added or deleted.
4 4
MANUAL SET UP
CHANNEL 30 (CATV)
or ADD
Select "ADD" or "DELETE"
5 5
To exit the C.RESET
EXIT
menu.
- 3 -
Clock Set Up
1
1
MENU
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
• If the clock is not set, the
or
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
2 2
CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
or
– – : – – – –
Select the current month
3
3
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
or HOUR MINUTE AM/PM
– – : – – – –
Select the current day
4
4
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 4
HOUR MINUTE AM/PM
or
– – : – – – –
Select the current year
5
5
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
or
0 5 : – – – –
Select the current hour
6 6
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
or
0 5 : 4 0 – –
Select the current minute
7
7
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
or
0 5 : 4 0 P M AM
B PM
Select "AM" or "PM"
8
8
To exit the CLOCK SET
screen.
Hint
Hint
• To go back one step, press the REW button
(during the steps [2] to [7].)
• Your clock setting will be lost if there is a
power failure or if the VCR has been
unplugged for more than 30 seconds.
EN