Troubleshooting - Sharp Aquos LC-60LE550U Operation Manual

Appendix

Troubleshooting

Problem
• No power
• Unit cannot be operated.
• Remote control unit does not
operate.
• Picture is cut off/with sidebar
screen.
• Strange color, light color, or
color misalignment
• Power is suddenly turned off.
• No sound
Possible Solution
• Check if you pressed POWER on the remote control unit.
If the indicator on the TV does not light up, press POWER on the TV.
• Is the AC cord disconnected? Page 9
• Has the power been turned on? Page 13
• External infl uences such as lightning, static electricity, may cause improper
operation. In this case, operate the unit after fi rst turning off the power of the TV or
unplugging the AC cord and replugging it in after 1 or 2 minutes.
• Are batteries inserted with polarity (e, f) aligned?
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fl uorescent lighting?
• Is a fl uorescent light illuminated near the remote control sensor?
• Is the image position correct? Pages 25 and 26
• Are screen mode adjustments such as picture size made correctly?
• Adjust the picture tone. Page 19
• Is the room too bright? The picture may look dark in a room that is too bright.
• Is the sleep timer set? Page 14
• Check the power control settings.
• The unit's internal temperature has increased. Remove any objects blocking vent or
clean.
• Is connection to other components correct?
• Is the volume too low? Page 14
• Is "Variable" selected in "Output Select"?
• Have you pressed MUTE on the remote control unit?
• Check the audio output of the connected external equipment. Is the volume too low
or muted?
• When external equipment is connected via an HDMI cable, you may need to
confi gure the audio to be output through the HDMI cable.
• When audio is not output from external equipment connected to the PC IN or
HDMI IN 1 terminal, check the "PC Audio Select" setting.
• Even when external equipment is connected using an HDMI-certifi ed cable, an audio
cable connection may be required depending on the type of equipment and the
media being played back. In this case, in addition to connecting an HDMI-certifi ed
cable to the HDMI IN 1 terminal, connect a ø 3.5 mm stereo minijack cable to the
AUDIO IN terminal and set "PC Audio Select" to "HDMI1".
• When connecting a PC via an HDMI-certifi ed cable, check the following:
- Is the audio output of the PC confi gured correctly? Check the audio output
settings and output audio format in Sound Properties on the PC.
Only PCM format audio can be output. Compressed audio (with a sampling rate of
32kHz, 44.1kHz, or 48kHz) and DTS format audio cannot be output.
- Depending on the board, only video signals may be output. In this case, in addition
to connecting an HDMI-certifi ed cable to the HDMI IN 1 terminal, connect a ø 3.5
mm stereo minijack cable to the AUDIO IN terminal and set "PC Audio Select" to
"HDMI1". Page 21
• If you are using a DVI-HDMI conversion cable to connect external equipment to the
TV, check the following:
- Is an audio cable connected? The DVI-HDMI conversion cable is for video only.
Connect a ø 3.5 mm stereo minijack cable to listen to the audio.
- Is HDMI IN 1 being used? When the TV is connected to another HDMI IN terminal,
the audio and video are not output together even if a ø 3.5 mm stereo minijack
cable is connected to the shared AUDIO IN terminal for PC IN and HDMI IN 1.
- Is "PC IN" selected in "PC Audio Select"?
27
Page 13
Page 10
Page 17
Page 20
Page 12
Page 25
Page 14
Page 21
Page 21
Page 21