Advertisement
Quick Links
3-Button Garage Door
Remote Control
1. INTRODUCTION
In this package, you will find a Skylink
lithium battery, a mounting bracket, a visor clip and a double sided tape.
Garage Door
Transmitter
(Battery inside)
There are three buttons on transmitter G6T3, each button can be
programed to control Skylink garage door receiver Smart Button
or GB-318-3 or Skylink garage door opener directly.
Follow one or more instructions below in Section 2 to program transmitter
G6T3 to the receiver or receivers you want to control.
2a. PROGRAM TRANSMITTER TO RECEIVER GB-318
You need to do the programming in order to add the transmitter - remote
control to a receiver.
Refer to the receiver Smart Button
TM
Smart Button
GB-318 can learn up to 10 remote controls.
To program the transmitter to the receiver, follow the instructions below:
1. Press the learn button on the side of the Smart Button
2. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
3. Within 30 seconds, press any one of the 3 buttons
on the transmitter that you want to program to the
receiver.
4. Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes
in standby mode.
5. You may now operate the garage door opener
with this new remote control.
6. To program this transmitter to control another
receiver, repeat process (1) to (4) to program
another button on the remote control.
2b. PROGRAM A TRANSMITTER TO THE SKYLINK
OPENER - EQ SERIES
You need to do the programming in order to add the transmitter to a
®
Skylink
Garage Door Opener.
Skylink
®
Garage Door Opener can learn up to 16 remote controls.
To program the transmitter to the Garage Door Receiver, follow the
instructions below:
1. Press the LEARN/SET button once on the garage door opener.
2. Once the LEARN/SET buttton is pressed, the LEARN LED will flash.
You may release the LEARN/SET button.
3. Within 30 seconds, press any one of the 3 buttons on the transmitter
that you want to program to the receiver.
4. Once the transmitter is programmed, the LEARN LED will turn off.
5. You may now operate the garage door opener with this new transmitter.
6. To program a transmitter to control another garage door opener,
repeat process (1) to (4) to program another button on the transmitter.
Learn Button
Model G6T3
®
garage door transmitter with 3V
Mounting
Visor Clip
Double
Bracket
Sided Tape
TM
GB-318 user's instruction to set up the unit.
TM
GB-318.
Smart Button
GB-318
®
GARAGE DOOR
2c. PROGRAM A TRANSMITTER TO THE SKYLINK
OPENER - IQ SERIES
To program the transmitter to the Skylink
please follow the user's instruction from the Garage Door Opener.
Q: What can I do if the door opener does not react after I press the button on
the transmitter ?
A: - Ensure when the button on the transmitter is pressed, the red light on the
TM
GB-318
transmitter comes on. Otherwise, check if the battery is inserted properly.
- Make sure the correct button on the transmitter is pressed.
- Ensure the wires that were previously connected to the wall mounted
door control are not loose.
- Ensure the transmitter has been programmed to the receiver. Refer
to section 2 for how to program a transmitter to the receiver.
3 Volt lithium battery (CR 2032) (included).
It is time to change the battery when the red LED on the transmitter does
not turn on when either button is pressed.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Antenna
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE:
LED
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
Learn
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
Button
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
TM
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user's instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z842-001
Patent Pending
©2010 SKYLINK GROUP
®
IQ series Garage Door Opener,
3. TROUBLE SHOOTING
4. BATTERY
5. FCC
6. WARRANTY
7. CUSTOMER SERVICE
®
GARAGE DOOR
Advertisement
