Table of Contents
Advertisement
Quick Links
Introducing the USB 2.0 2.5" Enclosure
The 2.5" USB 2.0 to SATA Enclosure is designed to
support USB equipped computers. This enclosure
provides large capacity mobile storage using 2.5"
SATA hard disk drives through High-Speed USB
2.0, hot-swapping interface.
Key Features and Benefits
•
Quickly adds more storage space to your
USB-enabled PC
•
No driver installation required. Simply
install a 2.5" SATA (3 Gb/s or 1.5 Gb/s)
hard disk into the enclosure then connect to
a USB port
•
Supports Hi-Speed USB 2.0 data transfer
rate up to 480 Mb/s
•
Compliant with Universal Serial Bus 2.0
Specification
04-0651A
2.5" USB 2.0 to SATA Enclosure
Quick Installation Guide
1
Advertisement
Table of Contents
Related Manuals for SIIG 2.5" USB 2.0 to SATA Enclosu
Summary of Contents for SIIG 2.5" USB 2.0 to SATA Enclosu
- Page 1 2.5" USB 2.0 to SATA Enclosure Quick Installation Guide Introducing the USB 2.0 2.5" Enclosure The 2.5" USB 2.0 to SATA Enclosure is designed to support USB equipped computers. This enclosure provides large capacity mobile storage using 2.5" SATA hard disk drives through High-Speed USB 2.0, hot-swapping interface.
-
Page 2: System Requirements
System Requirements • Desktop or notebook PC with an available USB 2.0/3.0 port • Windows 7 (32-/64-bit) ) / Vista (32-/64- ® bit) / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000 SP4 Package Contents • 2.5" USB 2.0 to SATA Enclosure •... -
Page 3: Hardware Installation
USB power connector USB data (for extra power) connector Figure 2: USB cable Hardware Installation The following section guides you through the installation of your drive kit. Installing a 2.5" Hard Drive Remove the 2 screws in each side, see Figure 3. - Page 4 Take off the PCB and connect it to the hard disk drive, see Figure 5 and Figure 6. Figure 5 Figure 6...
- Page 5 Put the installed PCB with hard disk drive into the hard disk drive tray, see Figure 7. Figure 7 Hold onto the hard disk drive and turn the hard disk drive tray over. Secure the hard disk drive with four mounting screws, see Figure 8.
-
Page 6: Driver Installation
Slide the lower cover back into the case and secure it with the two mounting screws, then slide the upper cover back into the case and secure it with the two mounting screws. Use the included USB 2.0 data cable to plug the 2.5"... -
Page 7: Disconnecting From The Computer
Using the 2.5" USB 2.0 to SATA Enclosure An additional drive icon will appear in My Computer or Computer when the enclosure is plugged into a USB port. The drive acts just like a conventional hard drive in your system. Disconnecting From The Computer Before unplugging the 2.5"... - Page 8 You can now unplug or turn off the 2.5" USB 2.0 to SATA Enclosure. Windows Vista / Server 2008 Verify that the LED is not flashing before proceeding. Click the Safely Remove Hardware icon located in the system tray by the system clock.
- Page 9 Windows 2000 SP4 Verify that the HDD LED is ON or not blinking. Double click the Unplug or Eject Hardware icon located in the system tray by the system clock. Highlight USB Mass Storage Device, click Stop, OK, OK, then click Close. You can now unplug or turn off the 2.5"...
- Page 10 Blank Page...
-
Page 11: Technical Support And Warranty
(5) years from the date of purchase of the product. SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the product if defective in materials or workmanship. - Page 12 Fremont, CA 94538-3152, USA Phone: 510-657-8688 2.5" USB 2.0 to SATA Enclosure is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names used in this publication are for identification only and may be trademarks of their respective owners.
Need help?
Do you have a question about the 2.5" USB 2.0 to SATA Enclosu and is the answer not in the manual?
Questions and answers