Related Manuals for Hitachi CM2186A
Summary of Contents for Hitachi CM2186A
- Page 1 HITACHI COLOR DISPLAY CM2186A OPERATING GUIDE For ‘future reference,record the model and serial number of your display monitor. Model No. Serial No. The numbers are located on the rear of the set. Read the instruction inside carefully. Keep this manual for future reference.
- Page 2 All Rights Reserved Printed in Japan NOTICE The information in this document is subject to change without notice. Hitachi assumes no responsibility for any errors that may appear in this document. FCC STATEMENT For USA Model (CM2186A3LN) The following statement applies to this HITACHI product. Federal Communication...
- Page 3 I N S T R U C T I O N S T O U S E R : This equipment complies with the requirements of FCC (Federal Communication Commission) Class A equipments provided that the following conditions are met. (1) Video signal cables: Double shielded coaxial cables (so called FCC shield cable) should be used and Or, if normal coaxial cables...
- Page 4 - P O W E R S O U R C E F o r U S A M d e 1 (CM2186A3UY) This color display is designed to operate on loo-120 volts 50/60 Hz. Insert the power cord plug into a loo-120 volts 50/60 Hz safety grounded receptacle. D O N O T C O N N E C T T H E D I S P L A Y T O O T H E R T H A N T H - E S P E C I F I E D V O L T A G E .
- Page 5 C A U T I O N S O N U S E W A R N I N G S N E V E R R E M O V E T H E B A C K C O V E R Removal of the back cover must be done only by qualified personnel, Inside of this display monitor contains high voltage.
- Page 6 L O C A T I O N O F C U S T O M E R C O N T R O L S POWER SWITCH POWER INDICATOR ‘v x DEGAUSSING sw~~ci-i Fig. 1. Front View * C O N T R A S T A N D B R I G H T N E S S C O N T R O L S Adjust the picture contrast and brightness on the screen.
- Page 7 G B R AC INLET ,o 0 o,o] R.G.B. SIGNAL INPUT SYNC SIGNAL INPUT Fig.2. Rear view...
- Page 8 [SIGNAL CABLE CONNECTION] 75OHM termination switch Fig.3. Signal cable connec tion from signal gknerator generator from signal T-type connector Fig. 4. SignaI cable connection (loop-through state) S I G N A L C A B L E C O N N E C T I O N Connect R.G.B.
- Page 9 ‘- T i m i n g C h a r t ( Recommended Signal ) Horizontal 6 3 . 9 kHz T: Period F: Front porch 1: Sync width B: Back porch 2 . 3 6 ,uS D: Display time 11.92 d3 Vertical 60.0...
- Page 10 I N S T A L L A T I O N I N S T R U C T I O N F O R A D J U S T M E N T S CM2186A is adjusted to the standard signal timing at the factory as indicated in “Timing Chart”...
- Page 11 SIDE VIEW ADJUSTMENTVR ADJUSTMENT DRIVER Removal of lid, readjustment method Fig. 5 - 11 -...
- Page 12 Adjustment shown below by qualified personnel is required when signals other than the recommended signal are received. Refer servicing to your dealer. Picture deviated to Picture deviated Picture deviated...
- Page 13 Zulassunssschein HH 9/89 R6 Aufgrund 5 8 Abs. 2 dei Rantgenverordnung (ROV) vom 8. Januar 1487 (BGBI .I 5.114) wird der Firma Hitachi Sales Europa GmbH, Rungedamm 2,205O Ham- burg 80, die Zulassung der Bauart fUr folgenden Storstrahler erteilt: Gegenstand: Farbmonitor Type CM2186A,..
- Page 14 For Canada Model (CM2186A3UY) NOTICE : THISDIGITAL APPARATUS DOES NOT EXCEED CLASS A LIMITS FOR RADIO NOISE EMISSION FROM ii DIGITAL APPARATUS AS SET OUT IN THE RADIO INTERFERJZNCE REGULATIONS OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS. AVIS : APPAREIL NUMIhIQUE LE PaSENT N’lhET PAS DE BRUITS RADIOtiLECTRIQUES LIMITES...
- Page 15 S P E C I F I C A T I O N S COLOR DISPLAY TUBE ..al-inch (2OV) 90-degree, in-line gun trio-dot pitch, 0.31 mm with Anti-Reflection panel PHOSPHOR TYPE * . * * * . p22 120V range..