Classen TRS-20 TURF RAKE Operator's & Parts Manual
  1. Manuals
  2. Brands
  3. Classen Manuals
  4. Lawn and Garden Equipment
  5. TRS-20 TURF RAKE
  6. Operator's & parts manual

Classen TRS-20 TURF RAKE Operator's & Parts Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

TRS-20 TURF RAKE
(Serial No. 00127 & UP)
TSS-20 TURF SEEDER
(Serial No. 00143 & UP)
OPERATORS / PARTS MANUAL
Schiller-Pfeiffer, Inc.
1028 Street Road • Southampton, PA 18966
Telephone: 1-800-366-6268

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TRS-20 TURF RAKE and is the answer not in the manual?

Questions and answers

Related Manuals for Classen TRS-20 TURF RAKE

Summary of Contents for Classen TRS-20 TURF RAKE

  • Page 1 TRS-20 TURF RAKE (Serial No. 00127 & UP) TSS-20 TURF SEEDER (Serial No. 00143 & UP) OPERATORS / PARTS MANUAL Schiller-Pfeiffer, Inc. 1028 Street Road • Southampton, PA 18966 Telephone: 1-800-366-6268...

  • Page 2: Table Of Contents

    Replacing Shaft Assembly Only ......6 Recommended Height Adjustments......6 INTRODUCTION THANK YOU MEASUREMENTS Thank you for purchasing a CLASSEN TRS-20/ U.S. Units of measure are used in this manual. TSS-20. SERIAL NUMBERS READ THIS MANUAL Write frame and engine serial numbers, plus model Read this manual carefully in its entirety.

  • Page 3: Pre-Delivery Check List

    Servicing the TRS-20/TSS-20 regularly Add engine oil (refer to Engine manual) and correctly. Add fuel, start engine, test run. 10. Classen Mfg., Inc. parts and service. 11. Give the customer the Operator’ s Manual DATE SET UP and encourage customer to read it.

  • Page 4: Safety Precautions

    SAFETY PRECAUTIONS TRAINING Fill the fuel tank outdoors. Regard the unit as a piece of power equipment and teach this regard to all who If fuel is spilled, do not attempt to start the operate this unit. engine. Move away from the area of the spill Read the instructions carefully.

  • Page 5: Operation

    14. Stop the engine and disconnect the spark Turn choke on (closed). plug wire: Turn ignition switch to “on”. a) before checking, cleaning or working Move throttle control to high RPM setting. on unit Do not exceed 3600 rpm. b) after striking a foreign object (inspect Pull recoil starter rope until engine starts.

  • Page 6: Optional Blade Assemblies

    OPTIONAL BLADE REPLACING SHAFT ASSEMBLY ONLY ASSEMBLIES If replacing the existing shaft assembly, only follow steps 1 through 3 above. Proceed with the CHANGING BLADE ASSEMBLIES following steps. Within minutes your machine can be converted to Remove the two drive pulleys and bearing a turf rake, turf seeder or turf slicer by purchasing plates from the main shaft (one on each the optional blade assemblies available complete...
  • Page 7 Seeding/Multipurpose Height The seeding/multipurpose blades are used for cutting grooves for over-seeding and can also be used for verticutting grasses. To set the height properly place unit on the lawn surface and adjust the wheel height up (see Fig. 4 ). Adjusting the wheel height up lowers the blades.

  • Page 8: General Maintenance

    PERFORM THE FOLLOWING: SAFETY WARNING • When replacement parts are required, use genuine Classen parts or parts with TO PREVENT POSSIBLE EXPLOSION OR IGNITION equivalent characteristics including type, OF VAPORIZED FUEL, DO NOT STORE EQUIPMENT strength, and material. Failure to do so may...

  • Page 9: Care For Hydraulic System

    CARE FOR HYDRAULIC SYSTEM To keep the hydraulic system in working order, Open bypass valve by depressing bypass there are a few steps needed to take place. If plunger and holding. synthetic oil were used we would suggest a full Adjust control linkage such that synthetic oil such as Mobil 1 15W50, Quaker transmission control is stroking...

  • Page 10: Parts Main Frame Assembly

    PARTS MAIN FRAME ASSEMBLY...

  • Page 11: Parts Self Propelled Assembly

    PARTS SELF PROPELLED ASSEMBLY...

  • Page 12: Parts Handle Assembly

    PARTS HANDLE ASSEMBLY...

  • Page 13: Seeder/Multipurpose Blade Assembly

    SEEDER/MULTIPURPOSE BLADE ASSEMBLY QTY/PER PART NO. MACHINE DESCRIPTION 700025 Shaft w/ Blade Holders, Multipurpose 100310 Blade w/ 15/16” Holes, Multipurpose 500216 Bolt, 5/16-18 x 314 Grade 8 500217 Nut, 5/16-18 Tap Lock 600030 Shaft/Blades Sub-Assembly, Multipurpose 900026 Complete Multipurpose Shaft Assembly (Includes Shaft, Blades, End Plates, Bearings, Pulley, Key &...

  • Page 14: Seed Box Assembly

    100144 HOUSING CLIP 100358 SHUT-OFF END CLIP 100357 SEED BOX 100359 SHUT-OFF ASSEMBLY 500226 3/16 LOCK WASHER 100074 DECAL, “CLASSEN” 100355 8” SEED BOX DRIVE WHEEL 500225 3/16” x 3/4” BOLT 100067 SHAFT GUARD 100020 PLASTIC TIE 400038 MOUNTING BRACKET...

  • Page 15: Seeder Tire Scrape Installation

    SEEDER TIRE SCRAPE INSTALLATION SEED BOX INSTALLATION For shipping purposes only, the seed box assembly is attached to machine improperly. To set your machine correctly for operation, remove hairpin clip (A) from upper connecting rod (B). Slide upper rod out, allowing “A shaped”...

  • Page 16: Safety Decals

    KEY PART NO. MACHINE DESCRIPTION KEY PART NO. MACHINE DESCRIPTION 100341 Decal, “TSS-20” (Turf Seeder only) 100074 Decal, “Classen” 100069 Decal, “DANGER, Keep Hands and Feet Away” 100060 Decal, “CAUTION - Muffler and Shields 100070 Decal, “DANGER - Carbon Monoxide”...

  • Page 17: Notes

    NOTES...

  • Page 18: Warranty

    Effective April 1, 2007 For the period of two years from the date of purchase, CLASSEN MFG., INC. will repair or replace for the original purchaser free of charge, any part or parts found upon the examination of our factory authorized service station, or by the factory in Norfolk, Nebraska, to be defective in material or workmanship.

This manual is also suitable for:

Tss-20 turf seeder

Table of Contents