10. Hdmi Setup - Onkyo TX-NR525 Owner's Manual

Tuner
■
AM/FM Freq Step (North American and
Taiwanese models)
10 kHz/200 kHz:
9 kHz/50 kHz:
Select the frequency step according to your
area.
■
AM Freq Step (European, Australian and Asian
models)
10 kHz:
9 kHz:
Select the frequency step according to your
area.
For AM/FM tuning to work properly, you must specify
the AM/FM frequency step used in your area.
Note
• When this setting is changed, all radio presets will be deleted.
Auto Standby
■
Auto Standby
Off
On
When "Auto Standby" is set to "On", the ASb
indicator lights and the AV receiver will automatically
enter standby mode if there is no operation for 30
minutes with no audio and no video signal input.
"Auto Standby" will appear on the AV receiver's
display and OSD 30 seconds before the Auto
Standby comes on.
Default setting: On (European, Australian and
Asian models), Off (North American and
Taiwanese models)
Note
• Set to " On" , the Auto Standby function may activate itself
during playback with some sources.
• The Auto Standby function does not work when Zone 2 is on.
■
HDMI Through
Off
On
This setting enables or disables the Auto Standby
during HDMI Through by detecting the audio/video
input signal.
When this setting is set to "On", the AV receiver will
automatically enter standby mode if there is no audio
and no video signal input during HDMI Through for 30
minutes. (The Auto Standby function does not work
when Zone 2 is on.)
When this setting is set to "Off", the status of HDMI
Through is continued regardless of audio/video input
signal.
Tip
• Entering standby mode is possible by setting "HDMI CEC
(RIHD)" to "On" and using CEC-compatible component
regardless of the above-mentioned setting.
See "HDMI CEC (RIHD)" in "10. HDMI Setup" for linked
operation.
• When the HDMI Through is enabled, the power
consumption slightly increases.
Note
• This setting is fixed to "Off" when "Auto Standby" is set to
"Off".
En-52
Advanced Operations

10. HDMI Setup

■
HDMI CEC (RIHD)
Off
On
Turn this setting on to allow
components connected via HDMI to be controlled by
the AV receiver (➔ page 15).
Note
• When the setting is set to "On" and the menu is closed, the
names of connected -compatible components and
"RIHD On" are displayed on the AV receiver.
"Search..." → "(name)" → "RIHD On"
When the AV receiver cannot receive the name of the
component, it is displayed as "Player *
(" * " shows up and indicates the number of components,
when two or more are received).
• When an -compatible component is connected to
the AV receiver via an HDMI cable, the name of the
connected component is displayed on the AV receiver's
display. For example, while you are watching TV
broadcasting, if you operate a Blu-ray Disc/DVD player
(being powered on) with the remote control of the AV
receiver, the name of the Blu-ray Disc/DVD player will be
displayed on the AV receiver.
" "
• Set it to Off when a connected piece of equipment is not
compatible or it is unclear whether the equipment is
compatible or not.
• If operation is not normal when set to
setting to " Off " .
• Refer to the connected component's instruction manual for
details.
• When the "HDMI CEC (RIHD)" setting is set to "On", the
power consumption in standby mode slightly increases.
(Depending on the TV status, the AV receiver will enter
standby mode as usual.)
• When the source equipment is connected with the
connection, it may malfunction if "HDMI CEC (RIHD)" is set
to "On".
Operating
procedure
(➔ page 44)
-compatible
" or "Recorder * ", etc
" "
On , change the