Chicago Electric 45252 Owners Manual & Safety Manual
  1. Manuals
  2. Brands
  3. Chicago Electric Manuals
  4. Impact Driver
  5. 45252
  6. Owners manual & safety manual

Chicago Electric 45252 Owners Manual & Safety Manual

1/2'' electric impact wrench
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Chicago Electric 45252

Summary of Contents for Chicago Electric 45252

  • Page 2: Table Of Contents

    table of Contents Safety ............2 Maintenance ..........10 Specifications ..........8 Parts List and Diagram ......12 Setup ............8 Warranty ............ 15 Operation ............ 9 WaRninG SYmBOlS anD DeFinitiOnS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

  • Page 3: Electrical Safety

    electrical safety 1. power tool plugs must match the outlet. 4. Do not abuse the cord. never use the cord for never modify the plug in any way. carrying, pulling or unplugging the power tool. Do not use any adapter plugs with grounded Keep cord away from heat, oil, sharp edges power tools.

  • Page 4: Impact Wrench Safety Warnings

    power tool use and care 1. Do not force the power tool. use the 4. Store idle power tools out of the reach of correct power tool for your application. children and do not allow persons unfamiliar The correct power tool will do the job better and with the power tool or these instructions safer at the rate for which it was designed.

  • Page 5: Vibration Safety

    vibration Safety This tool vibrates during use. 2. Do not smoke during use. Nicotine reduces Repeated or long-term exposure to vibration may the blood supply to the hands and fingers, cause temporary or permanent physical injury, increasing the risk of vibration-related injury. particularly to the hands, arms and shoulders.
  • Page 6 Grounding tO pRevent eleCtRiC ShOCK anD Death FROm inCORReCt GROunDinG WiRe COnneCtiOn: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. never remove the grounding prong from the plug.

  • Page 7: Extension Cords

    extension Cords 1. Grounded tools require a three wire extension cord. 7. Make sure the extension cord is properly wired Double Insulated tools can use either and in good electrical condition. Always replace a two or three wire extension cord. a damaged extension cord or have it repaired by a qualified electrician before using it.

  • Page 8: Specifications

    Specifications Electrical Rating 120V~ / 60Hz / 7A 2100 RPM Motor No Load Speed 2700 BPM Maximum Torque 240 ft. lbs. Drive Size 1/2" 39lh 194601 Setup - Before use: Read the entiRe impORtant SaFetY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

  • Page 9: Operation

    Operating instructions Read the entiRe impORtant SaFetY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Workpiece and Work area Set up 1. Designate a work area that is clean and well- 3.

  • Page 10: Maintenance

    maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. tO pRevent SeRiOuS inJuRY FROm aCCiDental OpeRatiOn: Release the trigger and unplug the tool from its electrical outlet before performing any procedure in this section. tO pRevent SeRiOuS inJuRY FROm tOOl FailuRe: Do not use damaged equipment.

  • Page 11: Troubleshooting

    troubleshooting problem possible Causes likely Solutions Tool will not start. 1. Cord not connected. 1. Check that cord is plugged in. 2. No power at outlet. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.

  • Page 12: Parts List And Diagram

    parts list and Diagram pleaSe ReaD the FOllOWinG CaReFullY THe mANuFACTuReR AND/oR DIsTRIbuToR HAs PRovIDeD THe PARTs lIsT AND Assembly DIAGRAm IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT.

  • Page 13: Assembly Diagram

    assembly Diagram Item 45252 For technical questions, please call 1-800-444-3353. Page 13...
  • Page 14 Record product’s Serial number here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 14 For technical questions, please call 1-800-444-3353.

  • Page 15: Warranty

    limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • Page 16 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353...

Table of Contents