Download
Share
Print this page
Duerkopp Adler 744-122 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Duerkopp Adler Manuals
  4. Sewing Machine
  5. 744-122
  6. Installation instructions manual
Duerkopp Adler 744-122 Installation Instructions Manual

Duerkopp Adler 744-122 Installation Instructions Manual

Hide thumbs Also See for 744-122:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
Contents
Part 2: Installation Instructions Cl. 744-122
1.
Mobile Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.
Securing for Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.
Height of the Table Top (Working Height) . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.
5.
Attaching Machine Parts removed for Shipping . . . . . . . . . . . . . . . . . . . . . . .
6.
Connection to the Compressed Air Supply . . . . . . . . . . . . . . . . . . . . . . . . . .
7.
8.
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Home
Page
.
3
3
3
3
4
8
9
9

Advertisement

loading

Related Manuals for Duerkopp Adler 744-122

Summary of Contents for Duerkopp Adler 744-122

  • Page 1: Table Of Contents

    Home Contents Page Part 2: Installation Instructions Cl. 744-122 Mobile Stand ..........Securing for Transport .

  • Page 3: Mobile Stand

    Installing the 744-122 Installation is to occur as described in the following information. All necessary parts can be found in the attached package. Important Notice! The mains voltage and the nominal voltage (operating voltage) specified on the spar below the table top must be identical. All work on the electrical components is to be conducted by authorized personnel and with the mains plug pulled.

  • Page 4: Attaching The Machine Parts Removed For Shipping

    5. Attaching the Machine Parts removed for Shipping For reasons of transport the sewing unit was dis-assembled to about half of its total length. The parts are to be re-attached in the following order: 5.1 Left guide for the transport carriage –...
  • Page 5 – Mount the support 1 between the spars 3 with the screws 2. Swing the support 1 up. The hole in the support plate 6 must fit over the seating pin 5 located on the bottom of the angle 4. Align the guide rods 8 horizontally in the longitudinal (direction of the carriage transport) as well as the transverse direction.
  • Page 6 – Fasten the hose chain 14 to the mounting rods 12 with the brackets 13. When doing this let the hose chain hang through a bit so that there is enough lead length even with the transport carriage in its extreme right end position. –...
  • Page 7 5.2 Control unit The control unit is equipped with the screws 1 and the locking plate 2 for quick attachment and removal. Please note! Carefully insert the plugs into the back of the control unit. In as far as these are present, match the markings on the cables to those and the back of the unit.

  • Page 8: Connection To The Compressed Air Supply

    6. Connection to the compressed air supply For a fault-free operation of the pneumatic controls Seating Pressure of the Material Guide Rail observance of the following instructions and a supply of water-free, lubricated compressed air is Depending on the material to be sewn the seating essential.

  • Page 9: Connection To The Electrical Mains Supply And Checking The Direction Of Rotation

    7. Connection to the electrical mains supply and checking the direction of rotation Work on the electrical components of this sewing unit should only be conducted by authorized personnel and with the mains plug pulled. The mains voltage and the nominal voltage (operating voltage) must be identical.