® ® N T E L L I O U C H C R E E N E Y P A D N T E L L I O U C H C R E E N E Y P A D TABLE OF CONTENTS Installing the TS-1 in Existing Construction..........24 Installing the TS-1 in New Construction ............25...
In addition, an IR Sensor and a PROGRAM Jack (for installers) are hidden under the faceplate. The source components IR Sensor communicates with a (optional) Niles R-4 or R-8 Remote Control so you can conveniently operate the TS-1 at a distance. The PROGRAM Jack allows an installer to set custom features on the •...
E Y P A D DESCRIPTION/OPERATION OVERVIEW TS-1 Rear Description The TS-1 rear has two CAT-5 jacks for connection to a Niles Multi-Zone System (i.e., ZR-4630, TS-1 Front Description (continued) ZR-8630AV, or A4.6Ci) and an (optional) external IR sensor, as shown in Figure 2.
(Zone On) for more than 3 seconds will turn Navigation Keys on the zone you are in and turn on all other zones, as set by the ALL ON/PAGE switch (see the appropriate Niles Multi-Zone Control System Figure 3 Installation and Operation Guide). In newly-activated zones, the Touch Organization of an example TS-1 Touch Screen.
1. Touch (Sleep Timer) once to view the Sleep Timer screen. 2. Touch Stop once. 3. Touch OK to save the settings. continued on next page... Touch Touch Touch Figure 4 Navigating TS-1 Control Screens for an example Niles ZR Tuner.
ALL ON/PAGE switches (see the appropriate Niles Multi-Zone Control System 2. Touch – or + one or more times to decrease or increase the desired Installation and Operation Guide).
• Blue light (steady), Touch Screen off = Zone is on. For example, Figure 4 on page 10 shows three Control Screens for a Niles ZR Tuner: FM Favorites, • Blue light (steady), Touch Screen on, Master Key highlighted = Tuner Direct Access, and Tuner Control.
For normal cleaning, use a dry, soft cloth to wipe off the dirt. To remove (i.e., Solo, Solo IR, Select, Select IR, Numeric, or Transport). Either or both can be used in a Niles excessive fingerprints or other contamination, first moisten the cloth with water or a window- Multi-Zone System, such as the ZR-4630, ZR-8630AV, or A4.6Ci.
® ® N T E L L I O U C H C R E E N E Y P A D N T E L L I O U C H C R E E N E Y P A D SYSTEM CONFIGURATIONS (continued) Using a TSP-1 Power Module to Connect Additional TS-1s ®...
® ® N T E L L I O U C H C R E E N E Y P A D N T E L L I O U C H C R E E N E Y P A D SYSTEM CONFIGURATIONS (continued) INSTALLATION CONSIDERATIONS Adding an External IR Sensor...
® ® N T E L L I O U C H C R E E N E Y P A D N T E L L I O U C H C R E E N E Y P A D INSTALLATION CONSIDERATIONS Where to Mount a TS-1 Keypad (continued) Avoid installing the TS-1 Touch Screen Keypad in the following areas, which can degrade oper-...
® ® N T E L L I O U C H C R E E N E Y P A D N T E L L I O U C H C R E E N E Y P A D INSTALLATION CONSIDERATIONS (continued) Installing the TS-1 in New Construction For a new construction site, use our optional New Construction Bracket (FG01060) to provide a...
• Using a CAT-5 cable, connect SYSTEM as a home run to the appropriate zone jack on the Niles Multi-Zone System. For wiring consistency, follow the color codes shown in Figure 15. (Please refer to IMPORTANT warning on pages 24, 26).
Page 15
CONNECTING THE TS-1 NOTE: An IR Sensor is required when the built-in TS-1 IR Sensor is not located in an ideal location in a zone, or when pass-through IR commands (instead of Niles system commands) are needed to control a source component.
® ® N T E L L I O U C H C R E E N E Y P A D N T E L L I O U C H C R E E N E Y P A D MANUALLY PROGRAMMING THE TS-1 The TS-1 can be programmed manually by using a built-in utility program.
Page 17
MANUALLY PROGRAMMING THE TS-1 Documenting Programming Worksheets (continued) SCREEN 1 SCREEN 2 TS-1 MASTER KEY PROGRAMMING WORKSHEET DVD SCREEN SET Function Key Show Key Label Niles Command Function Key Show Key Label Niles Command Setup ____________________ Play ____________________ Play Menu...
Using Auto Configure When a Niles Multi-Zone System is first activated, each connected TS-1 automatically configures itself to match the multi-zone controller. However, if a TS-1’s display remains blank or (after editing a configuration) you want to reset a TS-1 to a basic system, then perform the following steps: 1.
FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must IR Sensor: RJ-45 for Three- and Four-Wire Connection to Niles IR Sensor be used with this equipment. Operation with non-approved equipment or unshielded cables is Serial: 3.5 mm mini-plug...