Advertisement
Table of Contents
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Carrier XPOWER 38VYX110
Summary of Contents for Carrier XPOWER 38VYX110
- Page 1 38VYX110/38VYX130 INSTALLATION MANUAL...
-
Page 2: Table Of Contents
• Never open system to atmosphere while it is under vacuum. • When the system must be opened for service, break vacuum with dry nitrogen. • Do not vent R-410A into the atmosphere. • Use only Carrier matching indoor units (Table I). Table I Heat... -
Page 3: Precautions For Safety
38VYX110/38VYX130 General information Precautions for safety • Perform installation work properly according to the Installation Manual. The unit must be installed according to the national plant- Inappropriate installation may result in water leakage, electric engineering standards. shock or fire. • Read this “PRECAUTIONS FOR SAFETY” carefully before •... -
Page 4: Accessory And Refrigerant
38VYX110/38VYX130 Accessory and refrigerant E N G L I S H Table II: Accessory and Installation Parts Outdoor unit Drain nipple Installation manual x 1 Waterproof rubber cap Refrigerant Piping • Use copper pipe with 1.0 mm or more thickness for Ø 15,87 mm. •... -
Page 5: Selection Of Installation
38VYX110/38VYX130 Selection of installation Installation Place Knockout procedure • A place which provides a specified space around the outdoor unit. • The indoor/outdoor connecting pipes can be connected to 4 • A place where the operation noise and discharged air are not directions. -
Page 6: Refrigerant Piping
38VYX110/38VYX130 Refrigerant piping E N G L I S H Flaring Align the centres of the connecting pipes and tighten the flare nut as strong as possible with your fingers. 1. Cut the pipe with a pipe cutter. Then fix the nut with a spanner and tighten it with torque wrench as shown in the figure. -
Page 7: Minimum Clearances
38VYX110/38VYX130 Minimum clearances Obstacle at rear side Upper side is free Single unit installation Obstacles at both right and left sides. or more or more • The height of the obstacle should be lower than the height of the outdoor unit. Serial installation of two or more units •... - Page 8 38VYX110/38VYX130 Minimum clearances E N G L I S H Obstacles at both front and rear sides Standard installation Open the upper side and both right and left sides. The height of obstacle at both front and rear side, should be lower than the height of the outdoor unit. Serial installation of two or more units Single unit installation or more...
- Page 9 38VYX110/38VYX130 Installation Knockout hole Waterproof rubber cap Drain nipple Drain nipple Waterproof rubber cap A Open • When there is a possibility of freezing of drain at the cold • In case of draining through the drain hose, attach the following district or a snowfall area, be careful for drainage ability of drain nipple and the waterproof rubber cap, and use the drain drain.
-
Page 10: Evacuating
38VYX110/38VYX130 Evacuating E N G L I S H Air Purge Vacuum pump • As shown in the right figure, connect the charge hose after the With respect to the preservation of terrestrial environment, manifold valves are closed completely. adopt “Vacuum pump” for air purge (Evacuate air in the •... -
Page 11: Electrical Connections
38VYX110/38VYX130 Evacuating Valve handling precautions • Open the valve stem or the handle until it strikes the stopper. It is unnecessary to apply further force. Size ø 9,52 33 a 42 N•m (3,3 a 4,2 kgf•m) • Securely tighten the cap with a torque wrench. ø... -
Page 12: Final Installation Checks
38VYX110/38VYX130 Final installation checks E N G L I S H Check and Test Operation • Check gas leakage at the flare nut connections, valve stem cap connections and service port cap fittings with a leak detector or soap water. For R410A, use the leak detector exclusively manufactured for HFC refrigerant (R410A, R134a, etc.). -
Page 13: Final Installation Checks
38VYX110/38VYX130 Final installation checks Installation/Servicing Tools diameter of the outdoor unit control valve (3 way valve) has been changed. (1/2 UNF 20 threads per inch) Changes in the product and components • In order to increase the pressure resisting strength of the refrigerant piping flare processing diameter and size of opposite side of flare nuts has been changed. - Page 14 38VYX 110-130 Via R. Sanzio, 9 - 20058 Villasanta (MI) Italy - Tel. 039/3636.1 The manufacturer reserves the right to change any product specifications without notice. November, 2003 Printed in Japan...
Need help?
Do you have a question about the XPOWER 38VYX110 and is the answer not in the manual?
Questions and answers