Page 1 Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo with single CD AM/FM stereo with in-dash six CD Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows...
Page 2: Table Of Contents
Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire Information Tire Inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Transmission operation Roadside Emergencies Hazard flasher switch Fuses and relays Changing tires Lug Nut Torque...
Page 3: Table Of Contents
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Engine Coolant Fuel information Air filter(s) Refill capacities Engine data Accessories Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from MNAO.
Page 4: Introduction
The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Mazda and its products visit the following website: • In the United States: www.mazdausa.com •...
Page 5 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by a bold WARNING statement. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the...
Page 6 Introduction BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1,000 miles (1,600 km) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in. SPECIAL NOTICES Event Data Recorder The computer in your vehicle is capable of recording detailed data potentially including but not limited to information such as:...
Page 7 Introduction Emission warranty The New Vehicle Limited Warranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Page 8 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Protecting the Fasten Safety Belt Environment Airbag - Front Airbag - Side Passenger Airbag Off Child Seat Child Seat Installation Child Seat Lower Warning Anchor...
Page 9 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Personal Alarm System Engine Oil Feature Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid Power Steering Fluid Level Emission System...
Page 10 Introduction INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of printing. Mazda may change the contents without notice. 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 11 Instrument Cluster 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 12: Instrument Cluster
Instrument Cluster Windshield wiper/washer Headlamp and turn control signal control (pg. 45) (pg. 34) Instrument cluster (pg. 14) Power mirror control* Speed controls* (pg. 50) (pg. 51) Instrument panel Driver air bag dimmer/dome light (pg. 95) control Manual tilt steering (pg.
Page 13 Instrument Cluster Passenger airbag off Audio system Hazard flasher control indicator (pg. 21) (pg. 184) (pg. 99) Cigarette lighter* (pg. 48) Air conditioning control Climate controls (pg. 32) (pg. 32) Fog lamp control* Rear window defroster (pg. 35) control Auxiliary power point (pg.
Page 14: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 15 Instrument Cluster 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap.
Page 16 Mazda dealer. Normal braking is still functional unless the brake system warning light also is illuminated. WARNING: If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately by an authorized Mazda dealer.
Page 17 ON, continues to flash or remains on, have the system serviced immediately by an authorized Mazda dealer. A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt.
Page 18 ON to check bulb. Blinking indicator indicates system has been disabled, refer to the Driving chapter. Note: If the light remains on, have the system serviced by an authorized Mazda dealer. Anti-theft system: Flashes when the Securilock Passive Anti-theft System has been activated.
Page 19: Gauges
Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
Page 20 Instrument Cluster Odometer: Registers the total miles (kilometers) of the vehicle. Trip odometer: Registers the miles (kilometers) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer.
Page 21: Entertainment Systems
Entertainment Systems AUDIO SYSTEMS AM/FM Stereo Single CD audio system — Satellite ready capability 1. CD: To begin CD play, insert a CD into the slot, label side up. The system will load the CD and begin play after a short pause. The track number will illuminate in the display.
Page 22 Entertainment Systems Press and hold CLOCK for approximately two seconds until a beep sound is heard. The clock’s current time will flash. Press SCAN adjust the hours. Press AUTO-M to adjust the minutes. Press CLOCK again to start the clock. NOTE: If the audio operation is selected while the clock mode is on, the selected audio mode will be displayed for ten seconds, then the display will revert to the clock mode.
Page 23 Entertainment Systems Press the FM/AM control to select a frequency. Press and momentarily hold the AUTO-M (Auto memory) control. The system will beep. Press the AUTO-M (Auto memory) control to select from the stored stations. One stored station will be selected and played each time the control is pressed.
Page 24 Entertainment Systems 11. DISC : Press to skip forward to the beginning of the next CD. 12. DISC : Press to skip back to the beginning of the previous 13. Volume/ON/OFF: Press to turn the system on/off. Turn to adjust the volume. 14.
Page 25 Entertainment Systems 16. FM/AM: Press to enter radio mode and select a frequency from FM1, FM2 or AM. 17. SAT: Your radio comes equipped with Satellite ready capability. This enables you to view the song titles, artist, and further information. The kit to enable Satellite reception is available through your dealer.
Page 26 Entertainment Systems 2. MD/TAPE: This control does not function on this audio system. It will function with a cassette or mini disc (MD) upgrade. 3. CLOCK: Press and release CLOCK to alternate between the time and the audio display. The clock can be set at any time when the ignition switch is in the ACC or ON position.
Page 27 Entertainment Systems 5. SCAN/DISP/ESN/AUTO-M SCAN: Press in radio or CD mode DISP/ESN for a brief sampling of all listenable stations or of each CD track. Press again to disable scan mode. If the unit is left in scan mode, normal play will resume where scan was selected.
Page 28 Entertainment Systems 7. Fast forward: In CD mode, press and hold to advance through a track at a high speed. 8. Rewind: In CD mode, press and hold to reverse through a track at a high speed. 9. PROG/RDM: Press during CD play for a random selection of songs.
Page 29 Entertainment Systems 14. Memory presets: Your audio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and 12 FM stations (six in FM1 and six in FM2). Select a frequency with the AM/FM. 15.
Page 30 Entertainment Systems GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio reception: •...
Page 31 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 32: Climate Controls
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. A/C: Press to activate A/C. The indicator light will illuminate to indicate A/C is functioning. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
Page 33 Climate Controls WARNING: Under some weather conditions, use of the recirculated air mode may lead to glass misting or fogging. Switch the air conditioner on and select the fresh air mode. Heated air can assist windscreen demisting. Operating tips • To reduce fog build up on the windshield during humid weather, place the air flow selector in the position.
Page 34: Lights
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Battery saver Your vehicle is equipped with a battery saver feature which, if you leave the headlamps on, automatically turns off the headlamps after 30 seconds when the ignition is in the OFF position.
Page 35 Lights Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking brake must be disengaged. WARNING: Always remember to turn on your headlamps at dusk or during inclement weather.
Page 36 Lights INSTRUMENT PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim. VERTICAL AIM ADJUSTMENT 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away.
Page 37: Turn Signal Control
Aftermarket photometric aimers are not recommended for use on Mazda vehicles. 6. Move the opaque cloth to cover the right-hand headlamp and repeat Steps 4 and 5 for the left-hand headlamp.
Page 38 Lights INTERIOR LAMPS Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR position and any door is open. When the control is in the OFF position, it will not illuminate when you open the doors.
Page 39: Bulb Replacement
Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see an authorized Mazda dealer. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America to ensure lamp performance, light brightness and pattern and safe visibility.
Page 40 Map lamps 168 (T10) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized Mazda dealer. Replacing headlamp bulbs NOTE: This procedure can be difficult. Your Mazda dealer has the proper tools, training and parts to perform this task.
Page 41 Lights 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the rubber boot from the lamp assembly by pulling on one of the tabs.
Page 42 10. Connect the electrical connector into the rear of the bulb until it “snaps.” Replacing front parking lamp/turn signal bulbs For bulb replacement, see your authorized Mazda dealer. Replacing side repeater bulbs 1. Turn the headlamp switch to off.
Page 43 Lights Replacing brake/tail/turn/backup lamps bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly.
Page 44 Lights Replacing high-mount brake lamp bulbs To remove the lamp assembly: 1. Remove the two screws and move the lamp assembly away from the liftgate. 2. Remove the bulb holder from the lamp assembly by depressing the snaps. 3. Pull the bulb straight out of the socket and push in the new bulb.
Page 45: Driver Controls
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF.
Page 46 Driver Controls Rear window wiper/washer controls For intermittent operation of rear wiper, rotate end of control upward to the position. For normal speed rear wiper operation, rotate control upward to To activate the rear washer, rotate the control to the position and release.
Page 47 Driver Controls WARNING: Adjusting the steering wheel while the vehicle is moving is dangerous. Moving it can very easily cause the driver to abruptly turn to the left or right. This can lead to loss of control or an accident. Never adjust the steering wheel while the vehicle is moving.
Page 48 Driver Controls 1. Power point 2. Cupholders 3. Utility compartment 4. Ash cup (if equipped) WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. AUXILIARY POWER POINT (12VDC) WARNING: Power outlets are designed for accessory plugs only.
Page 49: Power Windows
Driver Controls POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
Page 50: Mirrors
Driver Controls Note: The passenger window switches will not illuminate when the window control is in the LOCKED position. Press the left side to restore the window controls. Accessory delay With accessory delay, power windows and moonroof operate for up to ten minutes after the ignition switch is turned from the ACC or ON to the OFF position, the key is not in the ignition or until either front door is opened.
Page 51 Driver Controls Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Page 52 Driver Controls 3. Press the SET ACC control and release it. 4. Take your foot off the accelerator pedal. Note: • Vehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed.
Page 53 Driver Controls Increasing speed while using cruise control/speed control There are two ways to set a higher speed: • Press and hold the SET ACC control until you get to the desired speed, then release the control. You can also use the SET ACCEL control to operate the Tap-Up function.
Page 54 Driver Controls Turning off cruise control/speed control There are two ways to turn off the cruise control/speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed. • Press the cruise control/speed control OFF control.
Page 55 Driver Controls WARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. WARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening.
Page 56 Driver Controls CARGO SHADE (IF EQUIPPED) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. To install the shade: • Insert the ends of the cargo shade into the mounting features located behind the rear seat on the rear trim panels.
Page 57 Driver Controls LUGGAGE RACK The maximum load for the roof rack is 100 lbs (45 kg), evenly distributed on the cross-bars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the cross-bars (if equipped) as possible.
Page 58: Locks And Security
Locks and Security KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer.
Page 59 Locks and Security 7. Turn the ignition from the 3 (ON) position to the 1 (LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off. Door key unlocking/locking Two step door unlocking 1.
Page 60 Locks and Security CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 61 Locks and Security • weak or dead transmitter battery. The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote locking and unlocking features will operate independent of the ignition position; however, the panic feature will only operate when the ignition is in the 1 (LOCK) or 2 (ACCESSORY) position.
Page 62 Locks and Security Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash once and the perimeter alarm (if equipped) will start the arming process.
Page 63 Mazda authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure.
Page 64 Locks and Security To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 3 (ON). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN).
Page 65: Anti-Theft System
The SecuriLock passive anti-theft system is not compatible with non-Mazda aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Your vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer.
Page 66 • If two previously programmed coded keys are not available, you must take your vehicle to your Mazda authorized dealer to have the spare key(s) programmed. 2006 Tribute (j14)
Page 67 Steps 1 through 5. If failure repeats, take your vehicle to your authorized Mazda authorized dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), wait twenty seconds and then repeat this procedure from Step 1.
Page 68 Locks and Security PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubleshooting.
Page 69 Locks and Security Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter. • Unlock the doors with a key. Turn the key full travel (toward the front of the vehicle) to ensure the alarm disarms.
Page 70: Seating And Safety Restraints
Seating and Safety Restraints SEATING Adjustable head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 71 Seating and Safety Restraints WARNING: Not securing luggage or cargo while driving is dangerous as it could move or be crushed during sudden braking or a collision and cause injury. Make sure luggage and cargo are secured before driving. WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips and the shoulder belt snug across the chest.
Page 72 Seating and Safety Restraints Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’s seatback. Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness.
Page 73 Seating and Safety Restraints WARNING: To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped).
Page 74 Seating and Safety Restraints Heated seats (if equipped) To operate the heated seats: • Push the control located on the seat to activate. • Push again to deactivate. The heated seats will activate when the ignition is in the RUN position. REAR SEATS Head restraints (if equipped) The purpose of these head restraints is to help limit head motion in the...
Page 75 Seating and Safety Restraints Folding down rear seats (60/40 split bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraint under the front seat for storage. 3. Pull the seat release control. NOTE: Make sure the floor is clear of all objects before folding the seat. 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 76 Seating and Safety Restraints 4. Flip seat forward. Attach the safety belt web snap button to the quarter trim panel snap button. This will assure that seatbelt does not get caught by staying out of the seat back folding path. 5.
Page 77 Seating and Safety Restraints 6. Rotate seatback down into load floor position. Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and the RED seat unlatched indicator on release...
Page 78 Seating and Safety Restraints WARNING: Make sure safety belt buckle heads are through elastic holders on seat backs. Safety belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback.
Page 79: Safety Restraints
Seating and Safety Restraints To install the rear cushion 1. Insert rod ends into floor mounting points and push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of...
Page 80 Seating and Safety Restraints How does the Personal Safety System work? The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM).
Page 81 Seating and Safety Restraints Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear-facing child seats, this occurs because they are initially sitting very close to the airbag.
Page 82 Seating and Safety Restraints safety belt pretensioner activation depending upon safety belt usage. Refer to Safety restraints section in this chapter. Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during a frontal or near-frontal collision.
Page 83 Seating and Safety Restraints Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips and the shoulder belt snug across the chest. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained.
Page 84 Seating and Safety Restraints WARNING: Placing a child, 12 years or younger, in the front seat is dangerous. The child could be hit by a deploying airbag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side airbag (if equipped) in a moderate collision.
Page 85 Seating and Safety Restraints WARNING: All safety belts should be checked for proper function. Additionally, if the front airbags have deployed, the front pretensioners have also deployed and both front restraints must be replaced. After any vehicle collision, the safety belt system at all outboard seating positions (except driver, which has no “automatic locking retractor”...
Page 86 Seating and Safety Restraints How to use the automatic locking mode for use with child safety seats • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. •...
Page 87 Seating and Safety Restraints WARNING: After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which doesn’t have this feature) must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly.
Page 88 WARNING: Improper disposal of the pretensioner system or a vehicle with non-deactivated pretensioners is dangerous. Unless all safety procedures are followed, injury could result. Ask an authorized Mazda dealer how to safely dispose of the pretensioner system or how to scrap a front pretensioner-equipped vehicle.
Page 89 Mazda recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and an authorized Mazda technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 90 Seating and Safety Restraints WARNING: Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Interior in the Cleaning chapter. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.
Page 91 Seating and Safety Restraints Both the driver’s and passenger’s safety belt usages are monitored and either may activate the BeltMinder feature. The warnings are the same for the driver and the front passenger. If the BeltMinder warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activate the BeltMinder feature.
Page 92 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider... Crashes are rare events 36,700 crashes occur every day. The more we drive, the more we are exposed to rare events, even for good drivers.
Page 93 Seating and Safety Restraints Reasons given... Consider... I have an airbag Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. I’d rather be thrown clear Not a good idea. People who are ejected are 40 times more likely to DIE.
Page 94 Seating and Safety Restraints • The driver and front passenger safety belts are unbuckled WARNING: While the design allows you to deactivate your BeltMinder , this system is designed to improve your chances of being seat belted and surviving an accident, and we recommend you leave the BeltMinder system activated for yourself and others who may use the vehicle.
Page 95: Airbags
Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. WARNING: Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying...
Page 96 Do not modify the front end of the vehicle. WARNING: Additional equipment may affect the performance of the airbag sensors increasing the risk of injury. Consult your authorized Mazda dealership before installation of additional equipment. 2006 Tribute (j14) Owners Guide (post-2002-fmt)
Page 97 Seating and Safety Restraints Children and airbags For additional important safety information, read all information on safety restraints in this guide. WARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions rather than in the front seating position.
Page 98 Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 99 Seating and Safety Restraints • a readiness light and tone • diagnostic module • and the electrical wiring which connects the components. • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system.
Page 100 Seating and Safety Restraints For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing system uses a passenger airbag off or pass airbag off indicator which will illuminate and stay lit to remind you that the front passenger frontal...
Page 101 • If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat, and the system should be taken promptly to an authorized Mazda dealer for repair before that seat is occupied again.
Page 102 Seating and Safety Restraints The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the pass airbag off lamp may or may not be illuminated according to the table below.
Page 103 DO NOT attempt to repair or service the system; take your vehicle immediately to an authorized Mazda dealer. Ask the front seat occupant to sit in a rear seat until the air bag system if checked by the authorized Mazda Dealer.
Page 104 If any of these things happen, even intermittently, have the SRS serviced at your authorized Mazda dealership immediately. WARNING: Unless serviced, the system may not function properly in the event of a collision.
Page 105 Seating and Safety Restraints WARNING: Do not use accessory seat covers or non-Mazda leather seat upgrade kits. The use of accessory seat covers and kits may prevent the deployment of the side airbags and increase the risk of injury in an accident.
Page 106 Seating and Safety Restraints Side airbags, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of the front seats.
Page 107 Seating and Safety Restraints The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the system is indicated by one or more of the following: •...
Page 108 (if equipped), fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing side-curtain airbags. See your authorized Mazda dealer. WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and side-curtain airbags (if equipped) are provided.
Page 109 Seating and Safety Restraints • Two crash sensors mounted at lower B-Pillar (one on each side). • Two crash sensors located at the c-pillar behind the rear doors (one on each side). • Rollover sensor in the restraints control module (RCM). The side-curtain airbags (if equipped), in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision or rollover event.
Page 110 If any of these things happen, even intermittently, have the SRS serviced at your authorized Mazda dealership immediately. Unless serviced, the system may not function properly in the event of a collision.
Page 111: Child Restraints
WARNING: Disposing of an airbag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda dealer how to safely dispose of an airbag or how to scrap an airbag equipped vehicle. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
Page 112 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Mazda recommends use of a belt-positioning booster seat. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 113 Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? •...
Page 114 Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lb.
Page 115 Seating and Safety Restraints WARNING: Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision.
Page 116 • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 117 Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 118 Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 119 Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Page 120 Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Page 121 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use safety belts to attach the child seat.
Page 122 Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. WARNING: Attach LATCH lower attachments of the child seat only to the anchors shown.
Page 123: Tires, Wheels And Loading
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed...
Page 124 Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter.
Page 125 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Mazda to give you the following information about tire grades exactly as the government has written it. 2006 Tribute (j14)
Page 126 Tires, Wheels and Loading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Page 127 Tires, Wheels and Loading Glossary of tire terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry. • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture.
Page 128 (if equipped), at least monthly and before long trips. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Mazda recommends the use of a digital or dial type tire pressure gauge rather than a stick type tire pressure gauge.
Page 129: Tire Information
Tires, Wheels and Loading When weather temperature changes occur, tire inflation pressures also change. A 10° F (6° C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label.
Page 130 Tires, Wheels and Loading TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs.
Page 131 (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Mazda. Use of any tire or wheel not recommended by Mazda can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 132 Tires, Wheels and Loading It is recommended that the two front tires or two rear tires generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The installation of replacement tires with steel cord body plies in the tire sidewall may cause malfunction of the Tire Pressure Monitoring System (TPMS), and is not recommended (cord material information is molded...
Page 133 Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by a qualified technician at a Mazda dealer. Front wheel drive (FWD) vehicles and those with an independent rear suspension require alignment of all four wheels.
Page 134 Tires, Wheels and Loading • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (AWD) vehicles (front tires at top of diagram) 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 135 Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Page 136 Tires, Wheels and Loading 3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter.
Page 137 Tires, Wheels and Loading 8. U.S. DOT Tire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
Page 138 Tires, Wheels and Loading 13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or Tire Label which is located on the B-Pillar or the edge of the driver’s door.
Page 139 Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
Page 140: Tire Pressure Monitoring System (Tpms)
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)
Page 141 Tires, Wheels and Loading Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem.
Page 142 Tires, Wheels and Loading When your temporary spare tire is installed (if equipped) When one of your road tires needs to be replaced with the temporary spare (T-type spare/Mini spare or Dissimilar spare), the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle.
Page 143 1. Check your tire pressure to Light under-inflated ensure they are properly inflated; refer to Inflating your tires in this chapter. Mazda Motor Corporation recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge for increased accuracy.
Page 144 Tires, Wheels and Loading Low Tire Possible Customer Action Required Pressure cause Warning Light Flashing Warning Spare tire in Your temporary spare tire is in Light (flashes for use. Repair the damaged road a short time either wheel and re-mount it on the at start-up or vehicle to restore system while driving)
Page 145 Tires, Wheels and Loading How temperature affects your tire pressure The Tire Pressure Monitoring System (TPMS) monitors tire pressure in each pneumatic tire. The pressure in each tire is dependent upon several factors, one of them being the contained air temperature (temperature of the air inside the tire).
Page 146: Vehicle Loading
Tires, Wheels and Loading Follow these guidelines when using snow tires and traction devices: • SAE class “S” cables should ONLY be used on the front axle for P235/70R16 tires. • Install cables or chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines.
Page 147 Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label).
Page 148 Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) –...
Page 149 Tires, Wheels and Loading GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Page 150 Tires, Wheels and Loading GVWR (Gross Vehicle Weight MFD. BY FORD MOTOR CO. IN U.S.A. Rating) – is the maximum FOR MAZDA MOTOR CORPORATION DATE: XX/XX GVWR:XXXXXLB/ XXXXXKG allowable weight of the fully loaded FRONT GAWR: XXXXL REAR GAWR: XXXXLB...
Page 151 Tires, Wheels and Loading 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight –...
Page 152 Tires, Wheels and Loading 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Page 153: Trailer Towing
Tires, Wheels and Loading Special loading instructions for owners of pickup trucks and utility-type vehicles WARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’s Guide. WARNING: Loaded vehicles may handle differently than unloaded vehicles.
Page 154 Tires, Wheels and Loading Do not exceed the maximum loads listed on the Safety Compliance Certification Label. For load specification terms found on the label, refer to Vehicle loading in this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum...
Page 155 Tires, Wheels and Loading GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum Trailer Weight Maximum GCWR - lb. Range - lb. frontal area of (kg) (kg) trailer - ft 2.3L w/manual 5040 (2286) 1500 (680) 24 (2.2) transmission 2.3L 5100 (2313) 1500 (680) 24 (2.2) w/automatic...
Page 156 Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized Mazda dealer. Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch.
Page 157 Tires, Wheels and Loading Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first 500 miles (800 km) of towing a trailer, and don’t make full throttle starts. •...
Page 158: Recreational Towing
Tires, Wheels and Loading • Vehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer’s wheels. Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, •...
Page 159: Driving
Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated.
Page 160 Driving WARNING: If you smell exhaust fumes inside your vehicle, have your authorized dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
Page 161 Driving If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor. 3. Turn the key to 3 (ON) without turning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
Page 162 Driving Note: If the engine does not start within five seconds on the first try, turn the key to 1 (LOCK), wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel.
Page 163: Brakes
Driving Note: Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris. USING THE ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly.
Page 164 Driving Four-wheel anti-lock brake system (ABS) Since your vehicle is equipped with an Anti-lock Braking System (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and indicates proper functioning of the vehicle’s anti-lock brake system.
Page 165 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 166 Driving To release the parking brake, the brake handle may need to be pulled up slightly (1) to release pressure before pushing in the button (2). Push the button on the end of the parking brake handle and push the handle down as far as possible.
Page 167 Driving PREPARING TO DRIVE YOUR VEHICLE Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances. These special design features, such as larger tires and increased ground clearance, give the vehicle a higher center of gravity than a passenger car. WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Page 168: Transmission Operation
Driving AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the RUN position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the RUN position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly.
Page 169 Driving WARNING: Do not drive your vehicle until you verify that the brakelamps are working. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Page 170 Driving This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected.
Page 171 Driving D (Overdrive) The normal driving position for the best fuel economy. Transaxle operates in gears one through four. D (Overdrive) can be deactivated by pressing the O/D OFF switch on the side of the gearshift lever. This will illuminate the O/D OFF light and deactivate the overdrive.
Page 172 Driving 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. WARNING: When parking, do not use the gearshift in place of the parking brake.
Page 173 Driving When starting a vehicle with a manual transaxle, you must: 1. Put the gearshift lever in the neutral position. 2. Hold down the brake pedal. 3. Depress the clutch pedal to the floor. 4. Without depressing the accelerator pedal, turn the ignition to position 4 (START), release the ignition as soon as the engine starts.
Page 174 Driving Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts during light to moderate accelerations and cruises (for best fuel economy) Shift from: 10 mph (16 km/h) 20 mph (32 km/h) 32 mph (52 km/h) 37 mph (60 km/h) Reverse Make sure that your vehicle is at a complete stop before you shift...
Page 175 Driving Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Set the parking brake. 3. Depress the clutch, then shift into 1 (First). 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 176 Driving 4. Turn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Page 177 Driving • Illuminates when 4WD system requires service. Please bring your vehicle to your local authorized dealer for service. Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud and rough terrain and have operating characteristics that are somewhat different from conventional vehicles, both on and off the road.
Page 178 Driving • It often may be less risky to strike small objects, such as highway reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or rollover. Remember, your safety and the safety of others should be your primary concern.
Page 179 Driving WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency.
Page 180 Driving Avoid excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Mud and water NOTE: •...
Page 181 Mazda Motor Corporation joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”...
Page 182 Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control.
Page 183 The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability. For this reason, Mazda Motor Corporation strongly recommends that you do not make modifications...
Page 184: Roadside Emergencies
Roadside Emergencies HAZARD FLASHER CONTROL The hazard flasher is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash.
Page 185: Fuses And Relays
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Page 186 Roadside Emergencies Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuses. 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 187 Roadside Emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 15A* Trailer tow park lamps Radio (illumination) 15A* Front and rear park lamps 10A* Ignition switch Powertrain Control Module (PCM relay), Fuel pump relay, Main fan relay, High/Low speed fan relay 2, PATS module 15A*...
Page 188 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 10A* Instrument cluster Radio (power) 20A* Cigar lighter 20A* Front wiper motor, Front wiper washer Climate control system mode switch Canister vent, Speed control cancel switch 10A* Instrument cluster —...
Page 189 Roadside Emergencies WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.
Page 190 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 10A* 20A* Power point 20A* Fog lamps 15A* A/C clutch, A/C relay 30A* Anti-lock Brake System (ABS) solenoid 25A* I/P fuse panel (RUN/START) 50A** Ignition (main) 40A** Blower motor 40A** Accessory delay relay - Subwoofer and 4WD, Low beam...
Page 191 Mazda. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
Page 192 Roadside Emergencies 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY” When driving with one of the dissimilar spare tires listed above, do not: •...
Page 193 Roadside Emergencies • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: •...
Page 194 Roadside Emergencies WARNING: Changing a tire is dangerous if not done properly. If the vehicle slips off the jack, you or someone else could be seriously injured. Be sure to follow the directions for changing a tire, and never get under a vehicle that is supported only by a jack.
Page 195 Roadside Emergencies Unbuckle the strap and remove the jack and tools by pulling the right side up first. Remove the tools from the jack in order to remove the spare tire from under the vehicle. Note: For some non-cargo management system vehicles, the jack and tools are located in the right rear of the cargo area behind an access panel.
Page 196 Roadside Emergencies To remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jack bracket. 3. Dislodge the jack from the bracket and carefully guide jack down and out through trim opening, upper end out first.
Page 197 Roadside Emergencies If equipped with a tether, perform the following additional steps: 4. Lift the spare tire on end to access tether attachment (1). 5. Use the lug wrench to remove the lug nut from the spare tire tether. 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position.
Page 198 Roadside Emergencies Changing the flat tire 8. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 199 Roadside Emergencies • Rear 9. Lower the jack from its stored height to fit under the jacking notches. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground.
Page 200 Roadside Emergencies 11. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered.
Page 201 Roadside Emergencies • guide the jack bottom first in the trim opening and position in the bracket (3), • secure the retention clip on the upper part of the jack (2), and • close and tighten the thumbscrew (1). Make sure the jack is fastened so it does not rattle when you drive.
Page 202 If the spare tire carrier ratchets with very little effort, take the vehicle to your authorized Mazda dealer for assistance at your earliest convenience. If your vehicle is equipped with a trailer hitch, guide the tire with one hand;...
Page 203: Lug Nut Torque
M12 x 1.5 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Mazda recommended replacement fasteners. WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel.
Page 204: Jump Starting
Roadside Emergencies • If steam is coming from the engine compartment: do not go near the front of the vehicle. Stop the engine, then turn the ignition switch to the ON position without starting the engine. The radiator cooling fans will start to cool the engine. •...
Page 205 Roadside Emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
Page 206 Roadside Emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 207 Roadside Emergencies 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Page 208 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 209 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 210: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a slingbelt towing procedure. If your vehicle is to be towed from the rear using wheel lift equipment, it is recommended that the front wheels (drive wheels) be placed on a dolly to prevent damage to the automatic transaxle.
Page 211 Roadside Emergencies On 4WD vehicles, it is required that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground. If the vehicle is towed by other means or incorrectly, vehicle damage may occur.
Page 212: Customer Assistance
Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Authorized Mazda Dealer personnel, we recommend that you take the following steps: STEP 1: Contact Your Authorized Mazda Dealer Discuss the matter with an Authorized Mazda Dealer.
Page 213 STEP 2: Call the Mazda Regional Office If you feel that you still require assistance, ask the authorized dealer Service Manager to arrange for you to meet the local Mazda Service Representative. If more expedient, contact Mazda Canada Inc. Regional Office nearest you for such arrangements.
Page 214 Your complete satisfaction is the goal of Mazda Canada Inc. and our authorized dealers. Mazda’s participation in CAMVAP makes a valuable contribution to our achieving that goal.
Page 215 Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer. This is the quickest and best way to address the issue. If your concern has not been resolved by the CUSTOMER RELATIONS, SALES, SERVICE, or PARTS MANAGER, then please contact the GENERAL MANAGER of the authorized dealer or the OWNER.
Page 216 Tel: (787) 788–9300 This way, we can be sure to respond to you as efficiently as possible. That is our goal. If you live outside the U.S.A., please contact your nearest Mazda Distributor. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of...
Page 217 Richmond Hill, Ontario L4B 3K5 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO & VIRGIN ISLANDS Plaza Motors Corp. (Mazda de Puerto Rico) P.O. Box 362722, San Juan, Puerto Rico 00936–2722 TEL: (787) 788–9300 GUAM (d.b.a.
Page 218 The differences may make it difficult or even impossible for your vehicle to receive satisfactory servicing in other countries. We strongly recommend that you NOT take your Mazda outside the United States. 2006 Tribute (j14) Owners Guide (post-2002-fmt)
Page 219 Customer Assistance However, in the event that you are moving to Canada permanently, Mazda vehicles built for use in the United States could be eligible for exportation to Canada with specific vehicle modifications to comply with the Canadian Motor Vehicle Safety requirements.
Page 220 Customer Assistance ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’s performance or...
Page 221 Factory-authorized Mazda service publications are available for owners who wish to do some of their own maintenance and repair. When requesting any of our publications through an Authorized Mazda Dealer, refer to the chart below. If they don’t have what you need in stock, they can order it for you.
Page 222 P.O. Box 19734 Irvine, CA 92623–9734 Customer Assistance Center or toll free at 1 (800) 222–5500 If you live outside of the U.S.A., please contact the nearest Mazda Distributor. See the Mazda importers/distributors section in this chapter. 2006 Tribute (j14)
Page 223: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces.
Page 224 • Spray Engine Shampoo and Degreaser (0000–77–410E-09), available at your authorized Mazda dealer, on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine.
Page 225 Cleaning • 2.3L DOHC I4 Engine • 3.0L DOHC V6 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer.
Page 226 INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, dry cloth, or use Mazda Deluxe Leather and Vinyl Cleaner (0000–77–430E-15). • Avoid cleaners or polish that increase the gloss of the upper portion of the instrument panel.
Page 227 INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, dry cloth; you may also use Mazda Deluxe Leather and Vinyl Cleaner (0000–77–430E-15). • Do not use household or glass cleaners, as these may damage the finish.
Page 228 MAZDA CAR CARE PRODUCTS Your Mazda dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 229: Maintenance And Specifications
This could lead to vehicle damage or an accident and injuries. For expert advice and quality service, consult an authorized Mazda Dealer. The owner should retain evidence that proper maintenance has been performed as prescribed.
Page 230 Maintenance and Specifications SCHEDULE 1 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), whichever comes first) Months Maintenance Item x 1000 Km...
Page 231 *1 According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the recommended time or miles (kilometers) period to ensure long-term reliability. Refer to Fuel filter in the Maintenance and Specifications chapter for fuel filter replacement requirements.
Page 232 Maintenance and Specifications SCHEDULE 2 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), whichever comes first) Months 12 16 44 48...
Page 233 Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Months 12 16 44 48 Maintenance Item x 1000 Km 16 24 32 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) Engine coolant (yellow) Replace at first 160,000 km (100,000 miles) or 60 months;...
Page 234 The owner or a qualified service technician should make these vehicle inspections at the indicated intervals to ensure safe and dependable operation. Bring any problem to the attention of an authorized Mazda Dealer or qualified service technician as soon as possible. When Refueling •...
Page 235 Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Genuine Mazda parts are designed and built to provide the best performance in your vehicle. PRECAUTIONS WHEN SERVICING YOUR VEHICLE WARNING: A hot engine is dangerous.
Page 236 Maintenance and Specifications Working with the engine off • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in 1 (First).
Page 237 Maintenance and Specifications 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod. 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 238: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8.
Page 239 Maintenance and Specifications 3.0L DOHC V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10.
Page 240 Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Mazda specifications. Refer to Refill capacities in this chapter. WARNING: If you operate your vehicle in temperatures below 40°...
Page 241: Engine Oil
Maintenance and Specifications Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
Page 242 Maintenance and Specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within the MIN and MAX marks or the lower and upper holes, the oil level is acceptable.
Page 243 Maintenance and Specifications • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above the MAX mark or upper hole may cause engine damage.
Page 244 Maintenance and Specifications 3. Recheck the engine oil level. Make sure the oil level is not above the MAX or FULL mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until it is seated.
Page 245: Battery
If a replacement oil filter is used that does not meet Mazda material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Genuine Mazda oil filter (or another brand meeting Mazda specifications) for your engine application. BATTERY...
Page 246 Maintenance and Specifications WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the...
Page 247: Engine Coolant
Maintenance and Specifications NOTE: • The vehicle may need to be driven to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Page 248 Maintenance and Specifications Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: •...
Page 249 If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with yellow-colored Mazda Premium Engine Coolant meeting Mazda Specifications. To maintain the integrity of the coolant and the cooling system and maintain the warranty on the cooling system: •...
Page 250 Maintenance and Specifications water to the “FULL COLD” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.
Page 251 Not all coolant recycling processes produce coolant which meets Mazda recommended coolants. Use of a recycled engine coolant which does not meet the Mazda recommended coolant, may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner.
Page 252 Maintenance and Specifications • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
Page 253 Replace the fuel filter with an authorized Mazda part. The customer warranty may be void for any damage to the fuel system if an authorized Mazda fuel filter is not used.
Page 254 Maintenance and Specifications WARNING: If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury. WARNING: Automotive fuels can cause serious injury or death if misused or mishandled.
Page 255 Maintenance and Specifications • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. •...
Page 256 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Mazda fuel filler cap is not used. WARNING: The fuel system may be under pressure. Remove fuel filler cap slowly.
Page 257 However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized Mazda authorized dealer to prevent any engine damage. Fuel quality NOTE: If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular”...
Page 258 Maintenance and Specifications Cleaner air Mazda endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: •...
Page 259 Maintenance and Specifications For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
Page 260 Maintenance and Specifications Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel.
Page 261 If other than Mazda authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Mazda parts should be equivalent to genuine Mazda parts in performance and durability. 2006 Tribute (j14) Owners Guide (post-2002-fmt)
Page 262 Maintenance and Specifications WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.
Page 263 Maintenance and Specifications driving cycles without these or any other temporary malfunctions present, the indicator should turn off—A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required. If the indicator remains on, have your vehicle serviced at the first available opportunity.
Page 264 Maintenance and Specifications 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range.
Page 265 Maintenance and Specifications Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is warmed up (approximately 20 miles [30 km]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking.
Page 266 Maintenance and Specifications High fluid level Fluid levels above the crosshatch zone may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Page 267: Air Filter(S)
AIR FILTER Refer to scheduled maintenance for the appropriate intervals for changing the air filter element. When changing the air filter element, only use a genuine Mazda air filter element. WARNING: Don’t drive without an air filter. This could result in excessive engine wear.
Page 268 Maintenance and Specifications 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the air filter housing. 5. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 6.
Page 269: Refill Capacities
Maintenance and Specifications REFILL CAPACITIES Fluid Classification Application Capacity High Performance Fill to line on Brake fluid DOT 3 Motor reservoir Vehicle Brake Fluid 4.5 quarts Engine oil 2.3L I4 engine (4.25L) (including filter SAE 5W-20 change) 3.0L V6 engine 6.0 quarts (5.7L) 16.5 gallons Fuel tank (62.5L)
Page 270 Maintenance and Specifications Fluid Classification Application Capacity 2.3L I4 engine with manual 5.3 quarts (5.0L) transaxle Mazda 2.3L I4 engine yellow-colored Engine coolant with automatic 6.3 quarts (6.0L) Premium Engine transaxle Coolant 3.0L V6 engine 10.6 quarts with automatic (10.0L )
Page 271 Maintenance and Specifications ENGINE SPECIFICATIONS Engine 2.3L I4 engine 3.0L DOHC V6 engine Cubic inches Required fuel 87 octane 87 octane Firing order 1-3-4-2 1-4-2-5-3-6 Ignition system Coil on plug Coil on plug Spark plug gap 0.049–0.053 inch 0.052–0.056 inch (1.25–1.35mm) (1.32–1.42mm) Compression ratio...
Page 272 Maintenance and Specifications 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Page 273: Safety Compliance Certification Label
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety MFD. BY FORD MOTOR CO. IN U.S.A. Administration Regulations require FOR MAZDA MOTOR CORPORATION DATE: XX/XX GVWR:XXXXXLB/ XXXXXKG that a Safety Compliance FRONT GAWR: XXXXL REAR GAWR:...
Page 274 Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number. The Vehicle Identification Number (VIN) contains the following information: 1.
Page 275 Maintenance and Specifications TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a MFD. BY FORD MOTOR CO. IN U.S.A. FOR MAZDA MOTOR CORPORATION transmission/transaxle code on the DATE: XX/XX GVWR:XXXXXLB/ XXXXXKG Safety Compliance Certification FRONT GAWR: XXXXL REAR GAWR: XXXXLB WITH WITH...
Page 276: Accessories
Accessories CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’s hands.
Page 277: Index
......264 instrument panel ....226 Automatic transmission ....168 interior ........227 driving an automatic interior trim ......227 overdrive .........169 Mazda car care products ..228 fluid, refill capacities ....269 plastic parts ......225 washing ........223 Auxiliary power point ....48 waxing ........223 Axle wheels ........224...
Page 278 Index Clock adjust Emission control system ..261 6-CD in dash ......26 Engine ........271 AM/FM/CD .........21 cleaning ........224 Clutch coolant ........247 fluid ..........264 fail-safe cooling .......252 operation while driving ..172 idle speed control ....245 recommended shift speeds ..174 refill capacities ......269 service points ....238–239 Console ........47 overhead ........47...
Page 279 Index running out of fuel ....258 Inspection/maintenance (I/M) safety information relating to testing ........263 automotive fuels .....253 Instrument panel Fuses ........185–186 cleaning ........226 cluster ........14 lighting up panel and interior ........36 location of components ....14 Gas cap (see Fuel cap) ....256 Gas mileage (see Fuel economy) ....258 Gauges .........19...
Page 280 Index doors ..........58 Power mirrors ......50 Lug nuts ........203 Power point .........48 Luggage rack .......57 Power Seats .........72 Lumbar support, seats ....72 Power steering ......166 fluid, checking and adding ..263 fluid, refill capacity ....269 Power Windows ......49 Manual transaxle .......172 Preparing to drive your fluid, checking and adding ..267 vehicle ........167...
Page 281 Index Safety Compliance inflating ........127 Certification Label ....273 label .........139 replacing ........131 Seat belts (see Safety rotating ........133 restraints) ........79 safety practices .......132 sidewall information ....135 Seats ..........70 snow tires and chains ....145 child safety seats ....115 spare tire .........191 heated ........74 terminology ......127 SecuriLock passive anti-theft...
Page 282: Table Of Contents
Index Windows checking and cleaning ..240–241 power .........49 liftgate reservoir .....240 rear wiper/washer .....46 operation ........45 Windshield washer fluid and replacing wiper blades ...241 wipers Wrecker towing ......210 checking and adding fluid ..240 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)

This manual is also suitable for:

2006 tribute

Mazda Tribute Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Tires, Wheels and Loading

Driving

Roadside Emergencies

Quick Links

Table of Contents

Related Manuals for Mazda Tribute

Summary of Contents for Mazda Tribute

This manual is also suitable for:

Table of Contents