Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Mackie MR5mk2
Summary of Contents for Mackie MR5mk2
- Page 1 MR5mk2 High Resolution Powered Studio Monitor O W N E R ’ S M A N U A L...
-
Page 2: Important Safety Instructions
Important Safety Instructions 1. Read these instructions. 18. This apparatus has been equipped with a rocker-style AC mains power switch. This switch is located on the rear panel and should remain 2. Keep these instructions. readily accessible to the user. 3. -
Page 3: Table Of Contents
Mackie products. Correct disposal of this product. This symbol indicates that this product should not be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (EEE). -
Page 4: Introduction
The MR5mk2s were designed by our expert each other to produce the best possible sound. loudspeaker and transducer engineering teams at Mackie and EAW. These compact studio monitors can be All-New Transducers... used in a variety of applications, including small project studios, surround sound editing, home theater playback, The MR5mk2s feature a 5.25-inch high-precision,... -
Page 5: Quick Start
We realize that you can’t wait to hook up your new Control Room. Mackie MR5mk2 Studio Monitors and try them out. Nevertheless, please take the time to read this page NOW, and the rest can wait until you’re good and ready. -
Page 6: Rear Panel Description
Rear Panel Description This is where the signal is connected to the monitor 2. INPUT LEVEL and adjustments are made to the frequency response The MR5mk2 expects a line-level signal at its input. of the speakers to match the monitor’s location and the Use this control to adjust the sensitivity of the input room’s environment. -
Page 7: Low Freq Filter
5. POWER SWITCH Conversely, if the mixes are consistently too bright, then adding some additional high-frequency energy in Switch up to turn the MR5mk2 on. Make sure the the monitors satisfies your ears, and the resultant mix level control is down before you turn it on. When the has less HF content. -
Page 8: Protection Circuits
This speaker output and the MR5mk2’s input. The local protection operates independently for the Mackie dealer should be able to assist, or you can build low-frequency and high-frequency amplifiers. Therefore, your own. it is possible for only the low frequency or high... -
Page 9: Appendix A: Service Info
Appendix A: Service Information If you think your Mackie product has a problem, No Sound please check out the following troubleshooting tips and • Is the power indicator [8] on the front panel do your best to confirm the problem. Visit the Support illuminated? If not, refer to “No Power”... -
Page 10: Repair
Pacific Time), to explain the problem. They will tell you where the nearest factory-authorized service center is located in your area. Service for Mackie products living outside the United States can be obtained through local dealers or distributors. -
Page 11: Appendix B: Connectors
Appendix B: Connectors XLR Connectors 1/4" TS Phone Plugs and Jacks XLR connectors are used to make balanced “TS” stands for Tip-Sleeve, the two connections connections to the MR5mk2. They are wired as follows, available on a mono 1/4" phone jack or plug. They are according to standards specified by the AES (Audio used for unbalanced signals. -
Page 12: Appendix C: Technical Information
Appendix C: Technical Information MR5mk2 Specifications AC Power Requirements Acoustic Performance Free Field Frequency Response: 120 VAC, 60 Hz Europe: 240 VAC, 50 Hz 50 Hz – 20 kHz Korea: 220 VAC, 60 Hz Sound Pressure Level @ 1 meter, +4 dBu into Balanced Input: Japan: 100 VAC, 50/60 Hz 104 dB SPL @ 1m... -
Page 13: Mr5Mk2 Block Diagram
LO VDC TRANSFORMER – The following are trademarks or registered trademarks of LOUD Technologies Inc.: The Mackie logo, MR Series and the Running Man. This manual also contains names and marks of other companies which belong to those respective companies, and are hereby acknowledged. - Page 14 AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. SERIAL NUMBER THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S.
-
Page 15: Mr5Mk2 Limited Warranty
The Product Warranty will not extend to anyone other than the original purchaser of the product (hereinafter, “Customer,” “you” or “your”). For products purchased outside the U.S. or Canada, please visit www.mackie.com/warranty to find contact information for your local distributor, and information on any warranty coverage provided by the distributor in your local market. - Page 16 16220 Wood-Red Road NE • Woodinville, WA 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Central and South America: 425.487.4333 Middle East and Africa: 31.20.654.4000 Fax: 425.487.4337 • www.mackie.com E-mail: sales@mackie.com...