Setting Up Your Remote Control - Haier HL32K2a Important Safety Instructions Manual

Setting Up Your Remote Control

After it has been set up properly, your remote control
can operate in six different modes: TV, DVD, VCR,
SETBOX, CABLE or AUDIO.
Note
The remote control might not be compatible
R
with all DVD Players, VCRs and Cable boxes.
Control Operation
A
Program the Controller to work with your device.
B
Changing device mode by pressing the TV
CABLE, VCR, AUD key. When device is set, related
device LED will be on for 1 second and then be off.
C
Aim the remote at the device.
D
Use the other Controller buttons to operate the
device. Device LED will blink if user presses any key
(if the key has data in current mode.). If the key has
no data, then LED will not blink.
E
Default init status: TV/Haier codeset.
Manually Programming the Control
Y
Check the code no. from the code list.
A
Choose the device you want to program.
B
While Press and holding
key, and device LED will be ON. Keep the status for
about 3 seconds and the LED will blink, indicating
that the Controller is ready for programming, then
release both keys.
C
Led will blink once when you enter a digit key,
indicating the digit key is programmed. If 3 digits are
programmed successfully, device LED will be ON for
about 3 seconds and then blink twice per second.
Then User now can:
A) Try to operate the device by using power key.
B) If operation can be done, press
save current 3-digits code brand to EEPROM and
exiting manually programming mode.
C) Return to beginning of step 3. Reprogram the
control.
D
If user's input is incorrect, LED will blink 6 times
in 3 seconds (2 HZ). And then keep 2 HZ blink,
user now can return to step 3 and re-program the
device. Within 30 seconds, user should enter the
, DVD, STB,
ENTER key, press INPUT
ENTER key to
3-digit brand code corresponding to your device. If
time out or any key other than Power and digits is
pressed, LED will be off and manually programming
process is exit.
Manually scan mode
Y
With manually scan programming, the Controller tests all
the codes available in the codeset database and assign
the correct one for the selected device. Although this
method is more time consuming, it saves you the trouble
of looking up the brand codes necessary for manual
programming.
To manually-scan program the Controller:
A
Manually turn OFF the device for manually scan
mode. (TV, VCR, DVD, STB, cable box or audio
equipment).
B
Choose the device you want to program.
C
While Press and holding
and device LED will be ON. Keep the status for about
3 seconds and the LED will blink, indicating that the
Control is ready for programming, then release both keys.
D
CH+/CH- key. it will emit the
Press and release the
next or the previous POWER key code. The LED
blinks with 10 HZ freq, indicating that the Remote is
in manually scan mode.
E
CH+/CH- key repeatedly until the device
Press
switches ON (CH+ key conducts a upward search
while the CH- key conducts a downward search in
the code set database). When the device turns ON,
press and release the ENTER key to program the
Controller with the new code, saving the code to
EEPROM and exit.
F
After saving the new code, press
the device responds, no further programming is
required. If the device does not respond, repeat
step 3 through 5. And searching will start from
current code set.
To exit without programming, press any key or no key
was pressed in 30 seconds, manually scan mode will
be automatically exit. The code can not be saved to
EEPROM.
After searching the entire data base, this mode will be
automatically exited and led will blink for 3 times in
1.5 seconds. The code can not be saved to EEPROM.
Automatic Scan Programming the Controller
Y
To automatic scan program the Controller:
A
Manually turn OFF the device you wish to power scan.
Universal Remote Control
ENTER key, press INPUT key,
POWER key. If
Haier LCD HDTV EN-28