Table of Contents
Advertisement
Quick Links
PARTNER Contact Closure
Adjunct
Installation Instructions
BEFORE STARTING INSTALLATION, READ AND UNDERSTAND ALL SAFETY INSTRUCTIONS ON
PAGE 2.
The PARTNER® Contact Closure Adjunct is used with a PARTNER Advanced Communications System
processor module (available separately) to activate or deactivate up to two auxiliary devices such as
door locks or door alerts. Your PARTNER Contact Closure Adjunct package should include the parts
shown below. If any parts are missing, call the Lucent Technologies™ hotline at 1 800 628-2888.
PARTNER is a registered trademark and Lucent Technologies is a trademark of Lucent Technologies. VELCRO is a
registered trademark of the Velcro companies.
Copyright © 1997 Lucent Technologies
All rights reserved
Printed in U.S.A.
PA RT N ER
ct
su re A dj un
C on ta ct C lo
0A 1
MO DE L 95
10 78 81 43 5
PA RT NO .
P
50 V DC 1 AM
P
30 V AC 1 AM
INS TAL LAT ION
ENT IS FOR
THI S EQU IPM
CA UT IO N:
ON S SYS TEM
COM MU NIC ATI
S PAR TNE R
TEC HN OLO GIE
PARTNER Contact Closure Adjunct
#8 x 3/4" (1.9 cm) screws
CO NT AC T
2
CLO SED –
NOR MAL LY
–
COM MO N
OPE N –
NOR MAL LY
CLO SED –
NOR MAL LY
COM MO N
–
OPE N –
NOR MAL LY
1
CO NT AC T
ON LUC ENT
14-ft. (4.25 m) phone cord
ON LY.
S EQU IPM ENT
VELCRO
®
strips
Comcode 107915555
Issue 1
January 1997
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Lucent Technologies PARTNER Contact Closure Adjunct
Summary of Contents for Lucent Technologies PARTNER Contact Closure Adjunct
-
Page 1: Installation Instructions
#8 x 3/4" (1.9 cm) screws VELCRO ® strips PARTNER is a registered trademark and Lucent Technologies is a trademark of Lucent Technologies. VELCRO is a registered trademark of the Velcro companies. Copyright © 1997 Lucent Technologies Comcode 107915555 All rights reserved Issue 1 Printed in U.S.A. -
Page 2: Important Safety Instructions
Adjunct. The surge protector protects the Contact Closure Adjunct and the PARTNER ACS processor module, but not the device being controlled. Lucent Technologies 146G Surge Protector—SCL/8 is recommended. The maximum distance between the Contact Closure Adjunct and the device being controlled depends upon the device. - Page 3 Wall-Mounting and Connecting the Contact Closure Adjunct Mount the PARTNER Contact Closure Adjunct to the wall using either the #8 screws or the VELCRO® strips: Insert a screw into the wall through the screw hole in the tab at each end of the Contact Closure Adjunct.
- Page 4 At extension 10, press the programmable buttons assigned as Contact Closure buttons. The green LEDs next to those two buttons should light. Using a multimeter or continuity tester, perform the following tests: A) Attach the tester probes to the Normally Open and the Common screws for Contact Closure 1 on the Contact Closure Adjunct.
- Page 5 Typical Contact Closure Configurations Following are examples of typical configurations for a magnetic door lock, an electronic door lock, and an outside automatic gate. In each of these examples, the Contact Closure Adjunct is wall-mounted within 150 feet (46 m) of the PARTNER ACS processor module, although the distance could be as great as 800 feet (244 m) since only one device is being controlled.
- Page 6 The Normally Open and the Common terminals of Contact Closure 1 are wired (by a licensed electrician) to a grounded surge protector. (Lucent Technologies 146G Surge Protector—SCL/8 is recommended.) The grounded surge protector is located in the same building as the PARTNER ACS processor module and the Contact Closure Adjunct, and is wired (by a licensed electrician) to the electronic gate.
Need help?
Do you have a question about the PARTNER Contact Closure Adjunct and is the answer not in the manual?
Questions and answers