Advertisement
SFD-2 PLACEMENT FOR PROPER VENTILATION
Allow at least 6" (15 cm) of clear space above the SFD-2
chassis for proper ventilation, making sure the air vent slots in
the chassis cover remain unobstructed.
Be sure the SFD-2 is resting on a hard, flat surface.
SAFETY INSTRUCTIONS
1. Ventilation - Although your SFD-2 Digital Processor generates
only nominal heat in use, be sure that the ventilation slots in the
top cover have at least 6" of unobstructed air space above them.
2. Water and Moisture - This product should not be used near
water. To prevent fire or shock hazard, do not expose this
product to rain or moisture.
3. Heat - This product should be situated away from heat
sources such as radiators, heat registers, stoves, or other appli-
ances which produce heat.
4. Power Sources - This product should be connected to an AC
power source of the proper rated voltage. The original ship-
ping containers will stipulate the AC voltage this unit can oper-
ate with correctly.
5. Cleaning - A regular dusting with a soft, non-abrasive cloth
will generally keep the finish of the faceplate and chassis look-
ing like new. At no time should you allow any liquid to come in
contact with the SFD-2 Digital Processor; it may run into the
electronic circuitry and cause damage which will not be cov-
ered under your warranty.
6. Servicing - Do not open this product. No user serviceable
parts inside. Refer servicing to an authorized service technician.
7. Non-Use Periods - The power cord of this product should be
unplugged from the outlet when left unused for an extended
period of time.
8. Do not remove the SFD-2 chassis cover while the unit is
switched to the OPERATE mode or is connected to an AC
power source. Cover screws could fall through the ventilation
slots and cause electrical damage to the SFD-2.
PACKING MATERIALS
We recommend that you retain all of the packing material and
shipping boxes for your SFD-2 Digital Processor. They are cus-
tom designed to prevent shipping damage from occurring.
Sonic Frontiers, Inc. will accept no responsibility for any dam-
age occurring to an SFD-2 Digital Processor that is shipped in
packing material other than the original Sonic Frontiers packing
m a t e r i a l .
DISCLAIMER OF LIABILITY
Under no circumstances does Sonic Frontiers, Inc. assume lia-
bility or responsibility for injury or damages sustained in the use
or operation of this equipment or for damages to any other
equipment connected to it.
Sonic Frontiers, Inc. reserves the right to make design changes
or improvements without the obligation to revise prior versions.
All specifications are subject to change without notice.
LIMITED FIVE YEAR WARRANTY
Sonic Frontiers, Inc. warrants to the purchaser that each SFD-2
Digital Processor is free of manufacturing defects for a period
of five (5) years from the date of purchase. This five (5) year
limited non-transferable warranty excludes all vacuum tubes,
which we warrant for a period of twelve (12) months. To
receive this warranty, the original purchaser must complete and
mail to Sonic Frontiers, within thirty (30) days from the date of
purchase, the enclosed Warranty Registration Card. Sonic
Frontiers, Inc. will then validate the warranty to the original pur-
chaser. This warranty is subject to the following conditions and
l i m i t a t i o n s :
1. Warranty applies only to the original purchaser.
2. This warranty is void and inapplicable if the product has
been handled other than in accordance with the instructions in
this Owner's Manual, abused or misused, damaged by acci-
dent or neglect or in being transported, or the defect is due to
the product being tampered with, modified or repaired by any-
one other than Sonic Frontiers, Inc. or an authorized Sonic
Frontiers repair depot.
3. Warranty does not cover normal maintenance.
4. Sonic Frontiers, Inc. shall not be responsible in any way for
consequential or indirect damages or liabilities resulting from
the use and operation of the product covered herein or result-
ing from any breach of this warranty or any implied warranty
relating to said product.
During this period, Sonic Frontiers, Inc. will repair or replace
any defective components free of charge. A Return Authoriza-
tion Number (RA Number) is required before any product is
returned to our factory for any reason. This number must be visi-
ble on the exterior of the shipping container(s) for Sonic
Frontiers to accept the return.
Units shipped to us without a Return Authorization Number or
without a visible RA Number on the exterior of the shipping
container(s) will be returned to the sender, freight collect.
Units to be repaired by Sonic Frontiers, Inc. must be sent ship-
ping and insurance prepaid by the original purchaser in the
original packing material. A returned product should be accom-
panied by a written description of the defect. Repaired units
will be returned by Sonic Frontiers, Inc. shipping and insurance
prepaid. The sender's name, address and telephone or fax
number must accompany the unit.
All other warranties or conditions either written or implied
are void.
Note: In foreign markets (anywhere outside of Canada and the
USA), the warranty is supplied by the authorized International
Distributor. Exact terms and conditions may vary.
Advertisement
