Audio Setup; Option Setup - Denon S-5BD Owner's Manual

ENGLISH
Manual Setup

Audio Setup

Set the audio input and output.
Setting items
COAX Input Assign OFF : Do not assign coaxial digital connector.
Assign coaxial digital AUX1 : Sets to the digital audio input connector for AUX1.
connector. AUX2 : Sets to the digital audio input connector for AUX2.
NOTE
When set to "AUX1" or "AUX2", priority is given to output of COAXIAL
input signals over analog or OPTICAL input signals.
Dynamic Play Mode AUTO : Automatically ON when parallel drive possible.
When playing back on a OFF : Parallel drive is not performed.
2.0/2.1-channel setup, the
unused surround channels
(amps) are used together
with the front channels
(amps) to give improved
sound quality.

Option Setup

OPTION
Make various other settings.
Setting items
Volume Control Volume Limit : Make a setting for maximum volume.
Set the MAIN ZONE (room • OFF : Do not set a maximum volume.
where the unit is located) • 60 / 70 / 80
volume setting.
Power On Level : Define the volume setting that is active when the
power is turned on.
• Last : Use the memorized setting from the last session.
• 0 – 99 : The volume is adjusted to the set level.
GUI Screensaver : Make screensaver settings.
Make GUI related settings. • ON : If is no operation is performed for approximately three minutes
while the GUI menu or iPod playback screen is displayed, a screen saver
is activated. When you press
and the screen before that screen saver started is displayed.
• OFF : Screen saver is not activated.

Remote control operation
buttons
Default settings are underlined.
Setting details
Default settings are underlined.
Setting details
uio p , the screen saver is cancelled
Display the menu
Cancel the menu
Setting items
GUI Text : Display the details of operation when switching surround mode,
(Continued) input mode, etc.
• ON
• OFF
Master Volume : Display the master volume during adjustment.
• Bottom : Display at the bottom.
• Top : Display at the top.
• OFF : Turn display off.
When the master volume display is hard to see when superimposed
on movie subtitles, set to "Top".
Quick Start Mode ON : Start up time is faster but power consumption during standby is
Make Quick Mode settings. higher.
OFF : Turn off Quick Mode.
Remote Preset Codes
1. Select the device you want to register using
By registering the preset
confirm.
codes in the supplied
2. Select the first letter of the manufacturer's name using
remote control unit, you can
ENTER
operate a TV, satellite tuner
3. Select the manufacturer's name using
or cable TV made by other
confirm.
manufacturers.
4. The procedures for registering remote control codes and remote
control preset registration are displayed.
• Some devices you want to register may have more than one preset code.
In this case, after registering the preset code, try operating the device
with the remote control unit to check that it is working properly.
• For details on operating devices with the remote control unit after
registering the preset code, see "Operating Components" (vpage
59).
Trigger Out When Setting for Zone (MAIN ZONE/ZONE2):
Select the condition for Trigger out is activated through linkage to the power of the zone set to
activating Trigger Out for "ON".
the input source, surround
When Setting for Input Source:
mode, etc.
Activate trigger out when the input source set to "ON" is selected.
See "TRIGGER OUT Jacks"
(vpage 17) for more
Active for the zone set to "ON" with "When Setting for Zone".
information on trigger out.
When Setting for Surround Mode:
Activate trigger out when the surround mode set to "ON" is selected.
Active when the "MAIN ZONE" set to "ON" with "When Setting
for Zone" is selected, and when the input source set to "ON" with
"When Setting for Input Source" is selected.
• ON : Activate trigger on this mode.
• – – – : Do not activate trigger on this mode.
Move the cursor
Confirm the setting
(Up/Down/Left/Right)
Setting details
ui and press
to confirm.
ui and press
Return to previous menu
ENTER
to
ui
and press
ENTER
to