Related Manuals for BIXOLON SRP 770 - B/W Direct Thermal Printer
Summary of Contents for BIXOLON SRP 770 - B/W Direct Thermal Printer
- Page 1 USER’S MANUAL SRP-770 LABEL PRINTER JE68-00131B Rev. 1.05 www.samsungminiprinters.com...
-
Page 2: Safety Precautions
Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING WARNING Violating following instructions can cause serious injury or death. Violating following instructions can cause slight wound or damage the appliance. Do not plug several products in one You must use only the supplied adapter. -
Page 3: Table Of Contents
Note : Please keep the packing materials(①,②,④,⑥) for future repacking to send 1. Unpacking .................5 a printer for repairs. & Repacking ⑨ Label 2. Samsung Label Printer ..............6 ⑧ Operator’s Manual & CD (Paper) 3. Connecting the Power Supply ............7 4. -
Page 4: Samsung Label Printer
2. Samsung Label Printer 3. Connecting the Power Supply CAUTIONS: When connecting or disconnecting the power supply from the printer, make sure that Status Indicator the power supply is not plugged into an electrical outlet. And the power supply’s Feed Button rated voltage and your outlet’s voltage do not match, contact your dealer for... -
Page 5: Connecting The Interface Cable
4. Connecting the Interface Cable 5. Installing or Replacing the Paper Roll ① Open Cover ② Open Guides ③ Install Roll Universal Serial Bus Parallel Interface Serial Interface (USB) RS-232 default setting is 19200 baud, no parity, 8 data bits and 1 stop bit ④... -
Page 6: Setting The Dip Switches
Detect Gap and Density Detection Black-mark Selection Memory SRAM 20(High) Selection for Flash Rom Image Store Exhibition Normal mode SAMSUNG command Selection Demo mode Emulation Emulation Media Label Paper Developer Selection Normal Paper Default --- off Mode Without Auto Cuter... -
Page 7: The Peel-Off
8. The Peel-off 9. Using Fan Fold Paper Printers can Peel-off a single label. Insert paper through both the rear slot and guides. You must remove the label before the printer prints the next label. Adjust holders and guides to the width of the paper. Open the peel -off cover and turn on peeler switch. -
Page 8: Auto Cutter (Option)
10. Auto Cutter (Option) 11. Cleaning Head Auto cutter should be used for continuous paper only. ( i.e. roll paper) Paper dust on the heating elements may lower the printer quality. In this case, clean the print head as follows : 1. -
Page 9: Install And Uninstall Windows Driver
12. Install and Uninstall Windows Driver (3) Click “Install” Button. 12.1 Download install-program from Website (1) Execute web-browser.(Ex: Internet Explorer) (2) Type http://www.samsungminiprinters.com (3) Connect website. (4) In “Quick menu”, click download button. (5) Download “SRP-770_V3.X.X.exe” in SRP-770 section. 12.2 Install Windows Driver 12.2.1 Serial Parallel interface (1) Double click “SRP-770_V3.X.X.exe”... - Page 10 (5) Select interface (port) type. 12.2.2 USB interface A. Windows 95/98/ME (1) Double click “SRP-770_V3.X.X.exe” file. (2) Click “Next” Button. (6) Please reboot computer.
- Page 11 (3) Click “Install” Button. Select “USB” interface (port) type. Please turn-off printer and turn-on printer. Select operating system type. When “Add new hardware wizard” for install “USB print support” driver pops up, click “Next” button.
- Page 12 Please click “Next” button three times. Click “Install” Button. When “USB print support” driver is installed, your system automatically restart after 10 seconds. (10) After the system restart, please turn-on printer. B. Windows NT/2000 Double click “SRP-770_V3.X.X.exe” file. Click “Next” Button. Select operating system type.
- Page 13 Select “USB” interface (port) type. C. Windows XP/2003 Server Double click “SRP-770_V3.X.X.exe” file. Click “Next” Button. Please turn-off printer and turn-on printer. Click “Install” Button. * If you can see this dialog, don’t worry comment in dialog. Printer and driver work well. Please click “Yes” button.
- Page 14 * If you can see this dialog, don’t worry comment in dialog. Select operating system type. Printer and driver work well. Please click “Continue Anyway” button. If “Add new hardware wizard” for install “SAMSUNGSRP-770” driver pops up, click “Next” button. Select “USB”...
- Page 15 (1) Click on the Start button, and then click on Settings > Control Panel. (2) Double click “Add/Remove Programs” icon. (3) Select “SAMSUNG SRP-770 LABEL Windows Driver 3.X.X”. (4) Click “Change/Remove” button. *If you can see this dialog, don’t worry comment in dialog.
- Page 16 Select printer to remove. 12.4 Printer Settings Click “Uninstall” Button. Please reboot computer. 1) Measurement: Select measurement of “Top Margin”. (Inch or millimeters) 2) Top Margin: top margin value of paper 3) Density: Select density of printing quality. (0 ~ 20) 4) Media Type: Select paper media type.
- Page 17 7) Customer Paper Size 【 Specification 】 Printing method Thermal line printing Dot density 203 dpi (8 dot/mm) Printing width 25.4 ~ 101.6 mm Paper width 38.1 ~ 104 mm Printing speed 127 mm/sec Receive Buffer Size 4K Byte Note : Printing speed may be slower, depending on the data transmission speed ※...
Need help?
Do you have a question about the SRP 770 - B/W Direct Thermal Printer and is the answer not in the manual?
Questions and answers