Subscribe to Our Youtube Channel
Related Manuals for Zenoah MD6210M
Summary of Contents for Zenoah MD6210M
- Page 1 MD6210M 115 33 81-10 (001) Original Instruction OWNER’S MANUAL MISTER MD6210M GB-1...
- Page 2 COUNCIL’S DIRECTIVE. The products referred to are : DESIGNATION : MISTER (Back-pack garden mister) MANUFACTURER : Husqvarna Zenoah Co., Ltd. MODELS : MD6210M SERIAL NUMBERS DATING : 2010 and onwards (The year is clearly stated on the rating plate,...
-
Page 3: Table Of Contents
MD6210M SAFETY PRECAUTIONS Contents Warning labels bearing the mark on the product and in this Manual refer to important safety matters. Please familiarize your- 1. Parts location ..........3 self with them and observe them well. If a warning label on the product becomes soiled or detached, 2. -
Page 4: Specification
MD6210M 2. Specification MODEL MD6210M Dimensions (LxWxH)** 354x520x740 Dry weight* 12.7 Fuel tank capacity liter Engine type Air cooled 2-cycle gasoline engine Displacement 62.0 Air filter Half wet polyurethane foam Carburetor Diaphragm, rotary valve type Ignition system C.D.I. Spark plug NGK BPMR7A (Noise-proof) Operating engine speed* 2000 to 8900... -
Page 5: For Safe Operation
Operator’s manual. tions as well as long periods of 10. Husqvar na Zenoah has a exposure to vibration are men- policy of continuous product tioned as factors. In order to re-... - Page 6 MD6210M 5. For safe operation but do not squeeze the handles etc., paying attention to stan- with constant, excessive pres- dards and the recommendations sures. of farm work safety promotion or- e) If you feel discomfort, redness ganizations. and swelling of your fingers or any other part of your body, see a WORKING CIRCUMSTANCE doctor before getting worse.
- Page 7 MD6210M 5. For safe operation around 30 ~ 40 minutes per ses- • Prepare yourself physically on the sion, and take 10 ~ 20 minutes of day before spraying, by for ex- rest between work sessions. Also ample cutting down on alcoholic try to keep the total amount of beverages or late-night work.
- Page 8 • After chemical refilling, firmly tact the nearest ZENOAH servic- tighten the tank cap. If not fully ing dealer for assistance. Check- tightened the cap may become ing the fan is very important.
- Page 9 MD6210M 5. For safe operation a) When starting work, please pay consult a doctor immediately. all due consideration to the spray- When doing so, inform the doc- ing time, wind direction, etc., to tor of the name of the chemical ensure that no noise disturbance you were using, the conditions of or chemical hazard is caused to...
- Page 10 MD6210M 5. For safe operation part, or any lubricant, always be DISPOSAL sure to use only ZENOAH prod- • When you dispose of the ma- ucts or products which have been chine, do not disassemble the certified by ZENOAH for use with machine.
-
Page 11: Set Up
MD6210M 6. Set up FLEXIBLE HOSE and SWIVEL JOINT BEND PIPE AND MIST NOZZLE 1. Connect the blower and swivel joint with flexible hose. • Connect the swivel joint and bend pipe. Push the pipes Clamp both ends of the flexible hose securely with together and turn them so they lock in relation to one the hardware supplied with the unit. -
Page 12: Fuel
2-cycle gasoline engine use. dustless place. If Zenoah oil is not available, use an anti-oxidant added 2. Put fuel into the fuel tank to 80% of the full capacity. quality oil expressly labeled for air-cooled 2-cycle en- 3. -
Page 13: Operation
MD6210M 8. Operation ■ CONTROL ARM ADJUSTING IDLE SPEED • Hold the upper end of the control arm in hand and, • The idling speed is set for 2000 rpm at the factory. If it while pulling it away from the unit, rotate arm forward is necessary to adjust the idle speed, use the adjust- (anti-clockwise as the arrow direction) until it clicks. - Page 14 MD6210M 8. Operation The spray range is changed by shifting the bell posi- tion after loosening the lock ring. (A) Pulled out position: Long distance, narrow angle spray (B) Pushed In position: Short distance, wide angle spray 3. Start the engine and carry the unit on your back. 4.
-
Page 15: Maintenance
MD6210M 9. Maintenance Maintenance, replacement, or repair of the emission FUEL FILTER control device and systems may be performed by any non-road engine repair establishment or individual. • A clogged fuel filter may cause poor acceleration of the engine. Check periodically to see if the filter is WARNING clogged with dirt. - Page 16 MD6210M 9. Maintenance MUFFLER WARNING WARNING Never use the machine without the net of the ma- chine. Before each use, check that the net is at- • Inspect periodically, the muffler for loose fasten- tached in place and is free from any damage. ers, any damage or corrosion.
-
Page 17: Storage
MD6210M 10. Storage WARNING 1. Clean the chemical fluid tank and nozzle. 2. Remove dirt from the sprayer, inspect it for any dam- • When draining fuel, please be careful not to spill age or looseness, and, if any abnormality is found, it. -
Page 18: Troubleshooting Guide
→ clogged with dust → clean When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal oper-...
Need help?
Do you have a question about the MD6210M and is the answer not in the manual?
Questions and answers