Download Print this page
HP D7171A - NetServer - LPr Installation Manual
HP D7171A - NetServer - LPr Installation Manual

HP D7171A - NetServer - LPr Installation Manual

Hp netserver lp 2000r (1.13, 1.26 & 1.40 ghz) installation sheet
Hide thumbs Also See for D7171A - NetServer - LPr:

Advertisement

Sheet
Installation
GHz)
1.26
2000r
Netserver
Setting Up the HP Netserver LP 2000r (1.13 and 1.26 GHz)

Audience Assumptions

This guide is for the person who installs, administers, and troubleshoots
LAN servers. Hewlett-Packard Company assumes you are qualified in
the servicing of computer equipment and trained in recognizing hazards
in products with hazardous energy levels. The instructions in this
document are provided in greater detail in the HP Netserver LP 2000r
User Guide.

Configuring the HP Netserver

1. Power on the HP Netserver and the monitor:
q Insert the HP Netserver Navigator CD-ROM in the CD-ROM
drive.
q The server should boot from the HP Netserver Navigator CD
on its own; if not, turn the power off, wait 10 seconds and turn
the power back on again.
q If the system fails to boot, follow the instructions on the
screen.
q Press [F2] to enter setup, or
q Press [F4] to accept automatic configuration update (if
prompted to do so).
2. Configure the Netserver and Install the Network Operating
System (NOS):
q During the configuration process you will be asked to select
the NOS Installation Mode.
q From the HP Netserver Navigation Main Menu, view the
system Readme from the HP Navigator main menu for the
most current installation information.
q Use the HP NetServer Navigator to configure the Netserver.
If you use Navigator's Guided, Custom, or Replication
modes, you will be prompted through the process.
NOTE) If certain versions of the Microsoft Windows NT Server are used,
a prompt will appear indicating selections of automated or
manual NOS installation.
q )Choose the automated NOS installation mode for first-time
installations of Microsoft Windows 2000 (NT) Server on
factory-configured HP Netserver. You will be guided through
the process by a series of HP display screens.
and
(1.13
LP
HP
paper
recycled
on
Printed
Company.
Incorporated.
CamCar/Textron,
countries.
other
and
U.S.
are
2000
Windows
and
Corporation.
Intel
of
trademarks
Company.
without
language
another
be
may
document
this
by
protected
is
that
information
by
furnished
reliability
or
use
the
for
material.
the
with
connection
for
or
herein
contained
errors
purpose.
of
warranties
implied
this
to
regard
with
kind
change
to
subject
is
q )Perform a manual install if you are installing a NOS other
)
than Microsoft Windows 2000 (NT) Server or if you have
replaced HP components (for example, adding a SCSI
controller board from a third-party). You will need to use
the NOS vendor's installation process.
Before you leave the Navigator and install your NOS,
ensure you view and print the HP-customized NOS
installation instructions and create the driver diskette(s)
for the NOS you are installing.
)
)
)
3. Install or Configure Tape Backup Software:
q )If your Netserver uses a tape backup device, install and/or
configure the tape backup software now.
Refer to the Tape Backup Getting Started Guide for
instructions on installing and configuring the tape backup
software.
4. Refer to the HP Netserver Online Documentation CD-ROM:
q )Use this CD-ROM for updated information about your
HP Netserver and as reference for any additional information
not provided in this Installation Guide.
NOTE) If you plan to use the Integrated Remote Assistant (Integrated RA)
feature to run Netserver utilities remotely, the Utility Partition must
be created using the HP Netserver Navigator. If you choose the
Guide mode of configuration, the partition will be created
automatically. Otherwise, you will need to choose Install/Update
Utility Partition during the custom configuration process. For more
information on the Integrated RA feature, refer to the "Remote
Administrator Guide" found on the HP Netserver Online
Documentation CD-ROM.
5. Run DiagTools (Optional):
q )Create the HP DiagTools diskettes from the Netserver Utilities
(or Diskette Library) on the HP Netserver Navigator
CD-ROM.
q )Run HP DiagTools and after completing all the configuration
)
topics, save the support ticket to a diskette for future
reference.
2001
June
P4636-90008
Hewlett-Packard
2001,
Copyright
USA
95014
California
Avenue
Tantau
Communications
Division
Server
Company
Hewlett-Packard
of
trademark
registered
the
in
Microsoft
of
trademarks
95
Windows
,
NT
Windows
registered
are
Pentium
Hewlett-Packard
of
consent
written
to
translated
or
reproduced,
photocopied,
of
part
No
reserved.
are
rights
All
proprietary
contains
document
Hewlett-Packard.
not
is
that
equipment
on
software
responsibility
no
assumes
Hewlett-Packard
this
of
use
or
performance,
in
damages
consequential
or
for
liable
be
not
shall
Hewlett-Packard
particular
a
for
fitness
and
merchantability
)
)
the
to,
limited
not
but
including,
any
of
warranty
no
makes
Hewlett-Packard
notice.
document
this
in
contained
information
in
Printed
P/N
Cupertino,
10955
Technical
Network
a
is
Torx
registered
,
Microsoft
and
Intel
prior
the
copyright.
This
its
of
furnishing,
incidental
)
)
material,
without
The
n•šŒ†ˆ

Advertisement

loading

Summary of Contents for HP D7171A - NetServer - LPr

  • Page 1: Audience Assumptions

    This guide is for the person who installs, administers, and troubleshoots controller board from a third-party). You will need to use LAN servers. Hewlett-Packard Company assumes you are qualified in the NOS vendor's installation process. the servicing of computer equipment and trained in recognizing hazards Before you leave the Navigator and install your NOS, in products with hazardous energy levels.
  • Page 2: Familiarize Yourself

    Familiarize Yourself Opening the HP Netserver Front of HP Netserver Bezel Removed SCSI Drives SCSI Drives Control Panel Indicators Flexible Disk Power CD-ROM Drive SCSI Drive LEDs SCSI Drive LEDs Reset Power Switch Switch Power LED Temperature & Fans LED SCSI Status LED Redundant Power Supply...
  • Page 3: Installing Power Supplies

    Installing Memory (Continued) Installing Power Supplies System Board DIMM Slots Installing the PCI Accessory Board System Board 64-bit PCI Slot (1) Connector WARNING Always insert the power supply filler panel into an empty power supply bay. Operating with an empty bay could cause thermal damage to the Nerserver.
  • Page 4: Installing A Second Processor

    Installing the PCI Accessory Installing a Second Processor Board (continued) (continued) Pin-1 Marker WARNING Align pin 1 on the processor with pin 1 on the processor socket, or pin damage will occur. Tool Latch Hook Latch (hidden) Lower Heat Sink Processor Socket Installing a Second Processor...
  • Page 5 2-Post Rack Installation 2-Post Rack Installation (continued) NOTE The installed inner-rails shipped with the HP Netserver are used for the 4-post HP racks. These rails must be removed for 2-post rack installation and replaced with the mounting brackets. Flush Mounting Center Mounting 4-Post Rack Installation WARNING...
  • Page 6 4-Post Rack Installation (continued) Obtaining Additional Documentation For additional documentation, refer to your HP Netserver LP 2000r Online Documentation CD-ROM. You can also access additional information and documentation from HP's external web site, either by connecting directly or through your Online Documentation CD-ROM.