Connection Test - Philips 50PFL3908/F7 User Manual

IP configuration
In following cases, select IP configuration to set each setting as
necessary.
– When connection test failed with the setting of Connection test.
– When instructed by your Internet service provider to make specific
settings in accordance with your network environment.
3
Use ▲▼ to select IP configuration, then press OK.
4
Use ▲▼ to select a setting, then press OK.
Network selection IP setting mode
Wireless network setting IP address
IP configuration Subnet mask
Proxy configuration Default gateway
Primary DNS
Secondary DNS
MAC address
Auto Sets the IP setting automatically.
IP setting
mode
Manual Sets the IP setting manually.
A set of numbers which are assigned to
IP address* 1, 3
devices participating in a computer network.
A mask which is used to determine what
Subnet mask* 1, 3
subnet an IP address belongs to.
IP address of the network device (such as
Default gateway* 1, 3
router) which provides Internet access.
Auto Sets the DNS setting automatically.
DNS setting
mode
Manual Sets the DNS setting manually.
A server which handles the name and IP
2, 3
Primary DNS*
address over the Internet.
A server which handles the name and IP
2, 3
Secondary DNS*
address over the Internet.
An address which recognizes the devices
MAC address
connecting to the network. It is also called
Hardware Address.
*1Items can be selected only when IP setting mode is set to Manual.
*2Items can be selected only when DNS setting mode is set to Manual.
*3Use ▲▼ or the NUMBER buttons to input numbers. When you use ▲▼ to
input numbers, then press OK or input the triple digits by using the NUMBER
buttons, the cursor moves to the next entry field. When you use ▲▼ to
input numbers, then press OK or input the triple digits by using the NUMBER
buttons at the rightmost entry field, numbers will be stored and go back to the
previous menu.
Note
• The range of input numbers is between 0 and 255.
• If you enter a number larger than 255, the number will automatically be 255.
• The manually entered number will be saved even if you change the setting to Auto.
• If you want to enter 1 or 2 digit number in one cell, press OK to move on to the next
cell.
• If the entered IP address or the default gateway or primary DNS number is same as
the default setting, IP address setting will be set to Auto. (The manually entered
number will be saved).
• When IP address setting is set to Manual, the setting of DNS setting will automatically
be Manual and when IP address setting is set to Auto, you can set either Auto or
Manual for DNS setting.
Proxy configuration
3
4
Network selection
Wireless network setting
IP configuration
Proxy configuration
Manual
192.168.11.3
255.255.255.0
192.168.11.1
192.168.11.1
0.0.0.0
00:12:0E:10:09:15
Proxy setting
* Items can be selected only when Proxy setting is set to Use.
• The range of input numbers for the port number is between 0 and 65535.
• For proxy port, the selected ports may be blocked and not be able to use depending
• If the proxy address is entered with blank only, proxy server setting will be set to Do

Connection test

Perform the following steps to test your Internet connection after you
have connected an Ethernet cable or entered network settings such as
IP address, DNS settings, etc. manually.
2
3
Home network
4
• If the connection test for both Home Network and Internet pass, you are ready to
• If the connection test fails, check if the Ethernet cable is connected to this TV properly or if
Use ▲▼ to select Proxy configuration, then press OK.
Use ▲▼ to select a setting, then press OK.
Proxy setting
• Do not use is selected for default settings.
• If you need to change the proxy setting as instructed by your
Internet service provider to set the designated proxy address and
port, select Use.
Do not use
Not use the proxy server.
Use Uses the proxy server.
Selects the number or word by using
Proxy address*
▲▼◄►, then press OK.
Use ▲▼ or the NUMBER buttons to input
Proxy port*
numbers.
Note
(If you enter a number larger than 65535, it will be regarded as 65535.)
on your network environment.
not use.
Use ▲▼ to select Connection test, then press OK.
Press OK to select Start now.
• Connection test will start automatically and the test result for
Home Network and Internet will appear right after the
connection test finishes.
• "Testing..." is displayed while the connection test is in progress.
Internet
Pass Pass
Connection test is successfully completed.
Connection test for Home Network failed.
Fail -
Check the connection settings.
Connection test for Internet failed. Check the
Pass Fail
connection settings.
• If the connection test for Internet passes, speed test will start
automatically.
Press OK to go to the list of network status confirmation screen.
Note
use Net TV or network upgrade function using the internet without making any
additional settings.
you have entered all the required details for the wireless LAN connection properly.
39
English
Do not use
Description