Related Manuals for Haier HWM55-918P
Summary of Contents for Haier HWM55-918P
- Page 1 User’s manual Fully automatic washing machine This manual is for HWM55-918P Please read this manual carefully before using. Retain it for future reference.
-
Page 2: Table Of Contents
CONTENTS Names of the parts Safety precautions Installation and adjustment Preparation before washing Put in the laundries Usage of the detergent Use the operation buttons Close the top lid Finish washing Disposal after washing Trouble-shooting Answer to question Packing list Specification the back cover... -
Page 3: Names Of The Parts
Names of the parts Water inlet valve Water absorption Top lid cushion Control panel seat Liquid detergent inlet Liquid whitener inlet Power line Control panel film Hanging Back cover hole Lint filter Cabinet handle Filter cover Cabinet Drain hose handle Inner tub Pulsator Cabinet... -
Page 4: Safety Precautions
Safety precautions The washing machine must be positioned Please plug the power plug on special so that the plug is accessible .Be sure to receptacle.Be sure to use three-pins pull the plug off and close the water faucet power receptacle .Ensure that the in following cases:power failure,delivering earthing terminal of the power receptacle the machine ,setting the machine idle... - Page 5 Safety precautions Do not decompose, repair or alter the Do not stretch hands into the working machine by yourself. machine. It is dangerous even if the rotation is slow. Take special care of the children. Do not put any hot or heavy items (such Do not wash laundries with volatile as the kettle with hot water ) on the materials (such as thinner, petrol etc.)
-
Page 6: Installation And Adjustment
Installation and adjustment Please install and adjust the machine according to the requirement of the mannual. It is very important to your security and correct operating the machine. Install the bottom plate Insert the bottom plate to the pedestal from the front to Screw the back and the two fasteners to the opposite holes, then Front... -
Page 7: Install The Water Inlet Hose
Install the water inlet hose 1.Attach the water inlet hoses to water faucet . Using pliers,tighten the coupling . (As figuer 1) the water faucet NOTE:please check if the connection of the water inlet pipe is proper 2. Connect the other end to the water inlet valve . ( As figure 2) The water inlet hose Jointer of the water inlet hose... -
Page 8: Preparation Before Washing
Preparation before washing Preparation before washing 1.Connect the water inlet hose. Open the water faucet. 2.Confirm that the washing machine is earthed reliably. Then insert the power plug into the receptacle. The earth terminal shall not link to gas pipeline and faucet water pipeline. 3.Put up the drain hose. -
Page 9: Put In The Laundries
Put in the laundries The capacity of washing and spinning of he machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. One time washing quantity shall be lower than the rated capacity. The thickness, size, type of the cloth will influence the actual washing capacity. -
Page 10: Use The Operation Buttons
Use the operation buttons Description of the function of buttons Mode and meaning of the indicators On: indicate the program about to run,or indicate the selected mode or indicate the water level Flashing: indicate the running program, or indicate the selected mode or indicate the water level Child lock function Push down the button for 5 seconds ,the digitron displays “CL”.Then you can continue setting desired washing procedures.After setting ,push the “Start/pause”... - Page 11 Step of using the operation buttons and description of the steps Flashing Solid Wash Standard Remain(Minutes) Rinse Soak Spin Soft Tub dry Quick Reserve(Hours) POWER START/PAUSE PROGRAM DELAY WATER LEVEL 1.Push "POWER" button to switch on the power POWER 2.Push " PROGRAM " button to select suitable automatic program PROGRAM After the power is switched on,”STANDARD”...
-
Page 12: Close The Top Lid
Attention Even there's no water in the tub, the spinning will start after a certain period. Wash and spin after putting the damageable clothes into tuck net, to avoid scathe. Wash the laundries that are prone to lose colors separately from other laundries. When washing start or opening cover intermitting, the washing machine will begin to work after a period time, this is normal phenomenon. -
Page 13: Disposal After Washing
Disposal after washing After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Clean the detergent box with water. The method of dismantle and installation refer to the Install usage of dismantle and in stallation lint filter. -
Page 14: Trouble-Shooting Answer To Question
Trouble-shooting · Answer to question (If there’s breakdown, please pull off the power plug before checking) The following phenomenon are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. -
Page 15: Packing List
Common phenomena Phenomena Explanation The spinning is intermittent when it starts. Balance the laundries to avoid slanting. Push the “spin” button to select “Spin”, but it doesn’t The program is setting the drain time. Some time is work. needed before it starts spinning. There may be some water flowing out of the drain hose It is the water remained in the factory inspection of in the first use of the machine. - Page 16 Specification 220V /50Hz Rated voltage/frequency 1/12L 2/18L 3/24L 4/29L Water level/Water quantity(about) 5/33L 6/37L 7/41L 8/46L Injection pressure(MPa) 0.03MPa 1.0MPa ～ Washing/spinning capacity 5.5kg/5.5kg...