Page 1
High Efficiency Vaporizing System and Highly Durable Heaters Ensure 25% Increased Output. Modular Design for Easy, Cost Effective Maintenance. Standardized Interface Allows Interchangeable Control Modules on All Models. Illuminated Fluid Tank for Easy Monitoring for the Level of Fog Fluid. Electronic Low Fluid Monitoring Protects Pump from Running Dry Heavy-Duty, Quiet Pump for Continuous, Silent Operation.
Congratulations on the purchase of your new ANTARI X Fogger Introduction Thank you for choosing an ANTARI X Fogger. You now own a rugged and powerful state-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
Important Safeguards Danger of Electric Shock Keep this device dry. For inside use only. Not designed for outside use. For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care to determine that the unit is installed at the rated voltage. Always unplug your ANTARI Fog Machine before filling its tank.
Page 5
Never aim the output nozzle at open flames. If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified personnel in order to avoid a hazard. The output nozzle becomes very hot during operation (300 C).
Unpacking & Inspection Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact. Before beginning initial setup of your ANTARI Fog Machine, make sure that there is no evident damage caused by transportation. In the event that the unit's housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Operation Plug power cord into a grounded electrical outlet. urn power switch on rear of unit to " ON" position. Warm-up is complete when the display on control module.shows " Ready to Fog" To emit fog, press the appropriate button on the control module for the desired length of time.
Pressing the Function key will cycle through different options including Volume, Timer, Heat & Fan. The Enter (Volume) Key is used to select the desired option. To adjust fog output volume setting, simply go into Volume option. Adjust the volume...
Page 9
1% to nonstop burst) by means of Up / Down keys. Use Enter (Volume) Key to select each option and make changes as desired. To turn off the heater and fan, go into Heat & Fan option. Use Enter (Volume) Key to confirm the selection.
On X Foggers such as X-510, X-515 and X-530, X-20 uses only 1 channel to control volume output operation. On X Fazer such as X-310, X-20 uses 2 channels to control both fog volume and fan volume. Whatever channel you select on the unit, the channel next to it will be selected automatically for fan volume control.
Page 11
If Channel has a value from 0 to 5, the unit is OFF. Between the values 6 to 249 the volume of fog output is regulated.With 6 being the minimum volume of fog produced and 249 approaching the maximum. The volume output rises as the DMX value is increased.
Maintenance Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the system to prevent the accumulation of particulate matter in the heating element.
Performance Notes All fog machines develop condensation around the output nozzle. Because this may result in some moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off.
LIMITED WARRANTY Atari Lighting and Effect Ltd. warrants to the original purchaser that the ANTARI X Fogger will be free from original defects in workmanship and material for a period of six months from the date of purchase. During the warranty period, machines will be repaired or replaced at the option of If the purchaser returns a completed registration card to ANTARI or its designated dealer within 30 days of purchase, ANTARI will extend the...