System Exclusive Messages - Yamaha S08 Data List

1.7 Polyphonic aftertouch (Receive only)
This message conveys the pressure that is applied to the keyboard after playing a note (for
individual note numbers).
The pressure can be controlled independently for each note. This message will affect
currently-sounding notes.
The effect of this message is determined by the following Multi Part parameters.
1. PAT PITCH CONTROL
2. PAT FILTER CONTROL
3. PAT AMPLITUDE CONTROL
4. PAT LFO PMOD DEPTH
5. PAT LFO FMOD DEPTH
6. PAT LFO AMOD DEPTH
By default, there will be no effect.
The effect will apply to note numbers 36...97.
In the case of either of the following Multi Part parameter settings, that part will not receive
Polyphonic Aftertouch.
• RECEIVE CHANNEL AFTER TOUCH = OFF
• PART MODE = DRUM, DRUMS1, 2
2.

System exclusive messages

2.1 Parameter changes
This devices uses the following parameter changes.
[UNIVERSAL REALTIME MESSAGE]
1) Master Volume
2) Master Fine Tuning
3) Master Coarse Tuning
4) Global Parameter Control
1) Reverb Parameter
2) Chorus Parameter
5) Controller Destination Setting
1) Channel Pressure (After Touch)
2) Control Change
6) Key-Based Instrument Controllers
[UNIVERSAL NON REALTIME MESSAGE]
1) General MIDI System On
2) General MIDI 2 System On
3) General MIDI Off
4) Scale/Octave Tuning
5) Identity Request (INQUIRY MESSAGE)
6) Identity Reply (INQUIRY MESSAGE)
[XG PARAMETER CHANGE]
1) XG System on
2) XG System parameter change
3) Multi Effect1 parameter change
4) Multi Part parameter change
5) Drums Setup parameter change
[NATIVE PARAMETER CHANGE]
1) Native System parameter change
2) Remote Switch parameter change
3) Normal Voice parameter change
4) Drum Voice parameter change
[Others]
1) Master tuning
2.1.1 Universal realtime messages
2.1.1.1 Master Volume
11110000 F0H
01111111 7FH
01111111 7FH
00000100 04H
00000001 01H
* 0sssssss SSH
0ttttttt TTH
11110111 F7H
or,
11110000 F0H
01111111 7FH
0xxxnnnn XNH
00000100 04H
00000001 01H
0sssssss SSH
0ttttttt TTH
11110111 F7H
When this is received, the Volume MSB will be reflected by the System parameter
MASTER VOLUME.
The binary expression 0sssssss is expressed in hexadecimal as SSH. The same applies
*
elsewhere.
2.1.1.2 Master Fine Tuning (Global tuning)
11110000 F0H
01111111 7FH
0xxxnnnn XNH
00000100 04H
00000011 03H
0sssssss SSH
0ttttttt TTH
11110111 F7H
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
= Exclusive status
= Universal Real Time
= n:Device Number, x=ignored
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Fine Tuning
= Fine Tuning LSB
= Fine Tuning MSB
= End of Exclusive
The value set here is relative to 440Hz and will be added to or subtracted from RPN Fine
Tuning.
When the Multi number or the tone generetor mode is changed , Fine Tuning set here will
be restored to the default value.
Fine Tuning value
LSB(SS) MSB(TT)
00H 00H
00H 40H
7FH 7FH
2.1.1.3 Master Coarse Tuning (Global tuining in semitone steps)
11110000 F0H
01111111 7FH
0xxxnnnn XNH
00000100 04H
00000100 04H
00000000 00H
0ttttttt TTH
11110111 F7H
The value set here is relative to 440Hz and will be added to or subtracted from RPN
Coarse Tuning.
When the Multi nunber or the tone generetor mode is changed, Fine Tuning set here will
be restored to the default value.
Coarse Tuning Value
LSB MSB(TT)
00H 00H
00H 40H
00H 7FH
2.1.1.4 Global Parameter Control
2.1.1.4.1 Reverb Parameter
11110000 F0H
01111111 7FH
0xxxnnnn XNH
00000100 04H
00000101 05H
00000001 01H
00000001 01H
00000001 01H
00000001 01H
00000001 01H
0ppppppp PPH
0vvvvvvv VVH
11110111 F7H
Parameter(pp)
-------------------------------------------------------------------
pp=0 Reverb Type
pp=1 Reverb Time
2.1.1.4.2 Chorus Parameter
11110000 F0H
01111111 7FH
0xxxnnnn XNH
00000100 04H
00000101 05H
00000001 01H
00000001 01H
00000001 01H
00000001 01H
00000010 02H
0ppppppp PPH
0vvvvvvv VVH
11110111 F7H
Parameter(pp)
-------------------------------------------------------------------
pp=0 Chorus Type
pp=1 Mod Rate (Modulation Rate)
pp=2 Mod Depth (Modulation Depth) 0...127
pp=3 Feedback (Feedback Level)
pp=4 Send to Reverb
(Send Level from Chorus to Reverb)0...127
21
100 ÷ 8192 x (-8192) cents
100 ÷ 8192 x 0 cents
100 ÷ 8192 x (+8191) cents
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Coarse Tuning
= Coarse Tuning LSB
= Coarse Tuning MSB
= End of Exclusive
100 x (-64) cents
100 x 0 cents
100 x (+63) cents
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Global Parameter Control
= Slot path length = 1
= Parameter ID width = 1
= Value width = 1
= Slot path LSB = 1 (Effect 0101: Reverb)
= Slot path MSB = 1
= Parameter to be controlled.
= Value for the Parameter.
= End of Exclusive
Value(vv) Display
0...8 0:Room S
1:Room M
2:Room L
3:Hall M
4:Hall L (default)
8:GM Plate
0...127 0.6...11.0s Refer to Table#9
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Global Parameter Control
= Slot path length = 1
= Parameter ID width = 1
= Value width = 1
= Slot path LSB = 1 (Effect 0102: Chorus)
= Slot path MSB = 2
= Parameter to be controlled.
= Value for the Parameter.
= End of Exclusive
Value(vv)Display
0...5 0:GM Chorus1
1:GM Chorus2
2:GM Chorus3 (default)
3:GM Chorus4
4:FB Chorus
5:GM Flanger
0...127 0...15.5 Hz Refer to Table#10
2...127
0...127 0...63
0...127