Yamaha S08 Data List page 19

1.2.16 Decay Time
This messages adjusts the EG Decay Time that was specified by the sound data.
Control# Parameter
75 Decay Time
Increasing this value will lengthen the decay that follows an attack.
1.2.17 Vibrato Rate
This messages adjusts the vibrato rate (speed) that was specified by the sound data.
Control# Parameter
76 Vibrato Rate
The higher the value the greater the vibrato speed.
1.2.18 Vibrato Depth
This messages adjusts the vibrato depth that was specified by the sound data.
Control# Parameter
77 Vibrato Depth
Increasing this value will make the vibrato depth greater.
1.2.19 Vibrato Delay
This message adjusts the vibrato delay time before the vibrato (as specified by the sound
data) comes into effect.
Control# Parameter
78 Vibrato Delay
The higher the value the longer the delay.
1.2.20 Portamento Control
This message specifies the portamento source key number (the key number at which
portamento will begin).
Data of 0...127 specifies the portamento source key.
When Portamento Control is received, the currently-sounding pitch will change at a
Portamento Time of 0 to the key of the next-received note-on of the same channel.
Control# Parameter
84 Portamento Control
This is received even if RECEIVE PORTAMENTO = OFF.
1.2.21 Effect1 Depth (Reverb Send Level)
This message specifies the send level for the reverb effect.
Control# Parameter
91 Effect1 Depth
Increasing this value will produce a richer reverb. The effect of the value will depend on the
state of the reverb effect.
1.2.22 Effect3 Depth (Chorus Send Level)
This message specifies the send level for the chorus effect.
Control# Parameter
93 Effect3 Depth
Raising this value will increase the modulation or spaciousness. The effect of the value will
depend on the state of the chorus effect.
1.2.23 Effect4 Depth (Variation Effect Send Level)
This message specifies the send level for the variation effect.
Control# Parameter
94 Effect4 Depth
However, this is not received if the Variation Effect parameter Variation Connection = 0
(Insertion).
1.2.24 Data Increment/Decrement (for RPN)
This message increases or decreases the parameter value specified for RPN (see 1.2.22),
by increments of 1.
Control# Parameter
96 RPN Increment
97 RPN Decrement
The data byte is ignored.
1.2.25 NRPN (Non-registered parameter number)
This message is used to specify a sound parameter (such as vibrato, filter, EG, drum setup
etc.) as an offset value.
Use NRPN MSB and NRPN LSB to specify the parameter that you wish to modify, and
then use Data Entry (see 1.2.4) to set the value for the specified parameter.
Control# Parameter
98 NRPN LSB
99 NRPN MSB
If the Multi Part parameter RECEIVE NRPN = OFF, that part will not receive NRPN.
The following NRPN messages can be received.
Data Range
0...64...127
(-64...0...+63)
Data Range
0...64...127
(-64...0...+63)
Data Range
0...64...127
(-64...0...+63)
Data Range
0...64...127
(-64...0...+63)
Data Range
0...127
(C-2...G8)
Data Range
0...127
Data Range
0...127
Data Range
0...127
Data Range
--
--
Data Range
0...127
0...127
*1
NRPN Data Entry
MSB LSB MSB LSB Parameter name and value range
*2
01H 08H mm -- Vibrato rate
01H 09H mm -- Vibrato depth
*3
01H 0AH mm -- Vibrato delay
01H 20H mm -- Low pass filter cutoff frequency
01H 21H mm -- Low pass filter resonance
01H 63H mm -- EG attack time
01H 64H mm -- EG decay time
01H 66H mm -- EG release time
14H rr mm -- Drum low pass filter cutoff frequency
15H rr mm -- Drum low pass filter resonance
16H rr mm -- Drum EG attack rate
17H rr mm -- Drum EG decay rate
18H rr mm -- Drum instrument pitch coarse
19H rr mm -- Drum instrument pitch fine
1AH rr mm -- Drum instrument level
1CH rr mm -- Drum instrument panpot
1DH rr mm -- Drum instrument reverb send level
1EH rr mm -- Drum instrument chorus send level
1FH rr mm -- Drum instrument variation send level
MSB 14H - 1FH (for drums) is received when Multi Part parameter PART MODE =
DRUMS1, 2.
*1 Refer to 1.2.4
*2 '--' indicates that the setting value is ignored.
*3 Adjusts the time after the note is played until vibrato begins to take effect. The effect
will begin more quickly for higher values, and more slowly for higher values.
1.2.26 RPN (Registered parameter number)
This message is used to specify part parameters such as Pitch Bend Sensitivity or Tuning
etc. as an offset value.
Use RPN MSB and RPN LSB to specify the parameter that you wish to modify, and then
use Data Entry (see 1.2.4) to set the value of the specified parameter.
Control# Parameter
100 RPN LSB
101 RPN MSB
If the Multi Part parameter RECEIVE RPN = OFF, that part will not receive this message.
19
mm : 00H - 40H - 7FH (-64...0...+63)
mm : 00H - 40H - 7FH (-64...0...+63)
mm : 00H - 40H - 7FH (-64...0...+63)
mm : 00H - 40H - 7FH (-64...0...+63)
mm : 00H - 40H - 7FH (-64...0...+63)
mm : 00H - 40H - 7FH (-64...0...+63)
mm : 00H - 40H - 7FH (-64...0...+63)
mm : 00H - 40H - 7FH (-64...0...+63)
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
The effect will apply both to Decay 1 and 2.
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
rr : drum instrument note number
mm : 00H, 01H-40H-7FH (RND, L63...C...R63)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
(when Variation Connection = SYSTEM)
mm : 00H, 01H-7FH (OFF, ON)
(when Variation Connection = INSERTION)
Data Range
0...127
0...127