Specifications - Kenwood KRF-V8080D Instruction Manual

Specifications

AUDIO section
Rated power output during STEREO operation
DIN/IEC (63Hz ~ 12.5 kHz, 0.09 % T.H.D. at 6 Ω Ω Ω Ω Ω ) .........................
.............................................................................. 100 W + 100 W
Effective power output during SURROUND operation
FRONT
(63Hz ~ 12.5 kHz, 0.09 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven)
............................................................................... 100 W + 100 W
(1 kHz, 10 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven)
............................................................................... 130 W + 130 W
CENTER
(63Hz ~ 12.5 kHz, 0.09 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven) .....
.............................................................................................. 100 W
(1 kHz, 10 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven) ............... 130 W
SURROUND
(63Hz ~ 12.5 kHz, 0.7 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven)
............................................................................... 100 W + 100 W
(1 kHz, 10 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven)
............................................................................... 130 W + 130 W
SURROUND BACK/SUBWOOFER
(63Hz ~ 12.5 kHz, 0.09 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven) .....
............................................................................................... 100W
(1 kHz, 10 % T.H.D. at 6 Ω Ω Ω Ω Ω one channel driven) ................ 130W
Total harmonic distortion ....................... 0.009 % (1 kHz, 50 W, 6 Ω Ω Ω Ω Ω )
Frequency response
(CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
................................................. 10 Hz ~ 100 kHz, +0 dB ~ –3.0 dB
PHONO 'RIAA' response .............. 40 Hz ~ 20 kHz, +1.5 dB ~ –3.0 dB
Maximum input level
PHONO (MM) .................................... 40 mV, 1 % T.H.D. at 1 kHz
Signal to noise ratio (IHF'66)
PHONO (MM) ........................................................................ 75 dB
(CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
............................................................................................... 95 dB
Loudness control
VOLUME at –30 dB level ...................................... +6 dB (100 Hz)
Input sensitivity / impedance
PHONO (MM) ........................................................ 6.0 mV / 47 kΩ Ω Ω Ω Ω
(CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
.............................................................................. 500 mV / 47 kΩ Ω Ω Ω Ω
Output level / impedance
TAPE REC ............................................................... 500 mV / 1 kΩ Ω Ω Ω Ω
PRE OUT (SURROUND BACK CHANNEL) .................. 1 V / 1 kΩ Ω Ω Ω Ω
PRE OUT (SUBWOOFER) ............................................. 1 V / 1 kΩ Ω Ω Ω Ω
Tone control
BASS ................................................................ ±10 dB (at 100 Hz)
TREBLE ............................................................ ±10 dB (at 10 kHz)
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
Caution : Read this page carefully to ensure safe
operation.
DIGITAL AUDIO section
Sampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Input level / impedance / wave length
Optical ........................... (–15 dBm ~ –24 dBm), 660 nm ±30 nm
Coaxial ................................................................... 0.5 Vp-p / 75 Ω Ω Ω Ω Ω
VIDEO section
VIDEO inputs / outputs
VIDEO (composite) ................................................. 1 Vp-p / 75 Ω Ω Ω Ω Ω
S VIDEO inputs /outputs
S VIDEO (luminance signal) ................................... 1 Vp-p / 75 Ω Ω Ω Ω Ω
S VIDEO (chrominance signal) ....................... 0.286 Vp-p / 75 Ω Ω Ω Ω Ω
COMPONENT VIDEO inputs/ outputs
COMPONENT VIDEO (luminance signal) ............. 1 Vp-p / 75 Ω Ω Ω Ω Ω
COMPONENT VIDEO (CB/CR-signal) ............. ±0.32 Vp-p / 75 Ω Ω Ω Ω Ω
FM tuner section
Tuning frequency range ................................. 87.5 MHz ~ 108.0 MHz
Usable sensitivity
MONO .................. 1.3 µV (75 Ω Ω Ω Ω Ω )/ 13.2 dBf (40 kHz dev, S/N 26 dB)
STEREO ........... 45 µV (75 Ω Ω Ω Ω Ω )/ 42.1 dBf (40 + 6 kHz dev, S/N 46 dB)
Total harmonic distortion
MONO (1 kHz, 40 kHz dev) ....................... 0.2% (65.2 dBf input)
STEREO (1 kHz, 40 + 6 kHz dev) ............... 0.8% (65.2 dBf input)
Signal to noise ratio (DIN weighted at 1 kHz)
MONO ........................................................ 65 dB (65.2 dBf input)
STEREO ..................................................... 60 dB (65.2 dBf input)
Stereo separation (1 kHz) ........................................................... 36 dB
Selectivity (DIN ±300 kHz) .......................................................... 64 dB
Frequency response (30 Hz ~ 15 kHz) .................... +0.5 dB, –3.0 dB
AM tuner section
Tuning frequency range .................................... 531 kHz ~ 1,602 kHz
Usable sensitivity (30% mod, S/N 20 dB) ......... 16 µV / (600 µV/m)
Signal to noise ratio (30% mod, 400 Hz) ............................................
.................................................................. 50 dB (60 dBµV EMF input)
GENERAL
Power consumption .................................................................. 330 W
AC outlet
SWITCHED ........................................................ (total 90 W max.)
Dimensions ..................................................... W : 440 mm (17-5/16")
Weight (Net) ............................................................ 11.7 kg (25.8 lb)
H : 159 mm (6-1/4")
D : 392 mm (15-7/16")
47
EN