Page 1
Order Number: E74523-002 ® The Intel Desktop Board D510MO may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel Desktop Board D510MO Specification Update.
Contact your local Intel sales office or your distributor to obtain the latest specifications before placing your product order. Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the United States and/or other countries. * Other names and brands may be claimed as the property of others.
Page 4
Intel Desktop Board D510MO Technical Product Specification Specification Changes or Clarifications Table 1 indicates the Specification Changes or Specification Clarifications that apply to ® the Intel Desktop Board D510MO. Table 1. Specification Changes or Clarifications Date Type of Change Description of Changes or Clarifications •...
Intended Audience The TPS is intended to provide detailed, technical information about the Intel Desktop Board D510MO and its components to the vendors, system integrators, and other engineers and technicians who need this level of information. It is specifically not intended for general audiences.
Page 6
Intel Desktop Board D510MO Technical Product Specification Other Common Notation Used after a signal name to identify an active-low signal (such as USBP0#) Gigabyte (1,073,741,824 bytes) GB/sec Gigabytes per second Gbit Gigabit (1,073,741,824 bits) Kilobyte (1024 bytes) Kbit Kilobit (1024 bits)
Page 8
Intel Desktop Board D510MO Technical Product Specification 2.6 Thermal Considerations ..............57 2.6.1 Passive Heatsink Design in a Passive System Environment ..59 2.7 Power Consumption ................. 62 2.7.1 Minimum Load Configuration..........62 2.7.2 Maximum Load Configuration ..........62 2.8 Reliability ..................63 2.9 Environmental ................
Page 9
11. Connection Diagram for Front Panel Header ........51 12. Connection Diagram for Front Panel USB Header........53 13. Connection Diagram for Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support) ......53 14. Location of the BIOS Configuration Jumper Block ......... 54 15.
Page 10
Intel Desktop Board D510MO Technical Product Specification 24. Front Panel USB Header ..............49 25. Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support) ............49 26. Power Connector ................50 27. Front Panel Header ................51 28.
Product Description Overview 1.1.1 Feature Summary Table 2 summarizes the major features of Intel Desktop Board D510MO. Table 2. Feature Summary Form Factor Mini-ITX, (6.7 inches by 6.7 inches [170 millimeters by 170 millimeters]) compatible with microATX ® Processor Passively-cooled, soldered-down Dual-Core Intel Atom™...
Page 12
Intel Desktop Board D510MO Technical Product Specification Table 2. Feature Summary (continued) ® • Intel BIOS (resident in the SPI Flash device) BIOS • Support for Advanced Configuration and Power Interface (ACPI), Plug and Play, and SMBIOS • Support for PCI* Local Bus Specification Revision 2.3...
Product Description 1.1.2 Board Layout Figure 1 shows the location of the major components. Figure 1. Major Board Components Table 3 lists the components identified in Figure 1.
Front panel header Battery Front panel wireless activity LED header Intel NM10 Express Chipset Front panel USB header (with Intel Z-U130 USB Solid-State Drive (or compatible device) support PCI conventional bus connector PCI Express x1 Mini Card connector USB front panel header...
Tested memory http://www.intel.com/support/motherboards/desktop/sb/CS- 025414.htm Processor The board has a passively-cooled, soldered-down Dual-Core Intel Atom processor with integrated graphics and integrated memory controller. NOTE The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the processor heatsink area for maximum heat dissipation effectiveness.
Intel Desktop Board D510MO Technical Product Specification System Memory The board has two 240-pin DDR2 DIMM sockets and supports the following memory features: • DDR2 SDRAM DIMMs with gold-plated contacts • Unbuffered, single-sided or double-sided DIMMs • 4 GB maximum total system memory •...
Intel NM10 Express Chipset The Intel NM10 Express Chipset provides interfaces to the processor and the USB, SATA, LPC, LAN, PCI, and PCIe interfaces. The Intel NM10 Express Chipset is a centralized controller for the board’s I/O paths. NOTE The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the processor heatsink area for maximum heat dissipation effectiveness.
NOTE Support for LVDS configuration complies with the following: ® 1. “Unlocking” of critical settings of the LVDS configuration is supported via Intel Integrator Toolkit’s command-line tool. 2. Critical settings of the LVDS configuration are not exposed through Intel Integrator ®...
Intel Z-U130 USB Solid-State Drive (or compatible device) NOTE One of the front panel USB headers supports an Intel Z-U130 USB Solid-State Drive (or compatible device). Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable.
Intel Desktop Board D510MO Technical Product Specification Real-Time Clock Subsystem A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery.
PCI Conventional bus power management ⎯ Supports ACPI technology ⎯ Supports LAN wake capabilities 1.8.1 LAN Subsystem Drivers LAN drivers are available from Intel’s World Wide Web site. For information about Refer to Obtaining LAN drivers Section 1.2, page 16...
Intel Desktop Board D510MO Technical Product Specification 1.8.2 RJ-45 LAN Connector with Integrated LEDs Two LEDs are built into the RJ-45 LAN connector (shown in Figure 3). Figure 3. LAN Connector LED Locations Table 5 describes the LED states when the board is powered up and the 10/100/1000 Mbits/sec LAN subsystem is operating.
Product Description Audio Subsystem The board supports the Intel High Definition Audio subsystem. The audio subsystem consists of the following: • Intel NM10 Express Chipset • Realtek ALC662 audio codec The audio subsystem has the following features: • Advanced jack sense for the back panel audio jacks that enables the audio codec to recognize the device that is connected to an audio port.
Intel Desktop Board D510MO Technical Product Specification 1.9.1 Audio Subsystem Software Audio software and drivers are available from Intel’s World Wide Web site. For information about Refer to Obtaining audio software and drivers Section 1.2, page 16 1.9.2 Audio Connectors and Headers The board contains audio connectors and headers on both the back panel and the component side of the board.
Product Description 1.10 Hardware Management Subsystem The hardware management features enable the board to be compatible with the Wired for Management (WfM) specification. The board has several hardware management features, including the following: • Thermal and voltage monitoring • Chassis intrusion detection 1.10.1 Hardware Monitoring The hardware monitoring and fan control subsystem is based on the Winbond...
Intel Desktop Board D510MO Technical Product Specification 1.10.2 Thermal Monitoring Figure 5 shows the locations of the thermal sensors and fan header. Item Description Chassis fan header Thermal diode, located on the processor die Remote thermal sensor Figure 5. Thermal Sensors and Fan Header...
Product Description 1.11 Power Management Power management is implemented at several levels, including: • Software support through Advanced Configuration and Power Interface (ACPI) • Hardware support: ⎯ Power connector ⎯ Fan header ⎯ LAN wake capabilities ⎯ Instantly Available PC technology ⎯...
Intel Desktop Board D510MO Technical Product Specification 1.11.1.1 System States and Power States Under ACPI, the operating system directs all system and device power state transitions. The operating system puts devices in and out of low-power states based on user preferences and knowledge of how devices are being used by applications.
Product Description 1.11.1.2 Wake-up Devices and Events Table 9 lists the devices or specific events that can wake the computer from specific states. Table 9. Wake-up Devices and Events These devices/events can wake up the computer… …from this state (Note 1) S1, S3, S4, S5 (Note 1) PME# signal...
Intel Desktop Board D510MO Technical Product Specification 1.11.2 Hardware Support The board provides several power management hardware features, including: • Power connector • Fan header • LAN wake capabilities • Instantly Available PC technology • Wake from USB • Wake from PS/2 devices •...
Product Description 1.11.2.3 Instantly Available PC Technology Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to- RAM) sleep-state. While in the S3 sleep-state, the computer will appear to be off (the hard drive(s) and fan will power off, the front panel LED will blink). When signaled by a wake-up device or event, the system quickly returns to its last known state.
Intel Desktop Board D510MO Technical Product Specification 1.11.2.9 +5 V Standby Power Indicator LED The +5 V standby power indicator LED shows that power is still present even when the computer appears to be off. Figure 6 shows the location of the standby power indicator LED.
The US Department of Energy and the US Environmental Protection Agency have continually revised the ENERGY STAR requirements. Intel has worked directly with these two governmental agencies in the definition of new requirements. This Intel Desktop Board meets the ENERGY STAR requirements listed in Table 10 when used in corresponding system configurations.
Technical Reference Memory Map 2.1.1 Addressable Memory The board utilizes 4 GB of addressable system memory. Typically the address space that is allocated for PCI Conventional bus add-in cards, PCI Express configuration space, BIOS (SPI Flash), and chipset overhead resides above the top of DRAM (total system memory).
Intel Desktop Board D510MO Technical Product Specification The amount of installed memory that can be used will vary based on add-in cards and BIOS settings. Figure 7 shows a schematic of the system memory map. All installed system memory can be used when there is no overlap of system addresses.
Intel Desktop Board D510MO Technical Product Specification Connectors and Headers CAUTION Only the following connectors/headers have overcurrent protection: Back panel and front panel USB and PS/2. The other internal connectors/headers are not overcurrent protected and should connect only to devices inside the computer’s chassis, such as fans and internal peripherals.
Technical Reference 2.2.1 Back Panel 2.2.1.1 Back Panel Connectors Figure 8 shows the location of the back panel connectors. Item Description PS/2 keyboard/mouse connector PS/2 keyboard/mouse connector VGA port USB ports LAN connector (RJ-45) USB ports Line in Line out Mic in Figure 8.
Intel Desktop Board D510MO Technical Product Specification 2.2.1.2 I/O Shield The I/O shield provided with the board allows access to all back panel connectors and is compatible with standard mini-ITX and microATX chassis. As an added benefit for system configurations with wireless PCI Express Mini Card solutions, the I/O shield also provides pre-cut holes for user installation of up to three external wireless antennas.
Technical Reference 2.2.2 Component-side Connectors and Headers Figure 10 shows the locations of the component-side connectors and headers. Figure 10. Component-side Connectors and Headers...
Page 44
SATA connector 1 SATA connector 0 Front panel header Front panel wireless activity LED header Front panel USB header (with Intel Z-U130 USB Solid-State Drive, or compatible device, support) PCI conventional bus connector USB front panel header Front panel audio header...
Technical Reference 2.2.2.1 Signal Tables for the Connectors and Headers Table 13. Serial Port Header (COM 1 and COM 2) Signal Name Signal Name DCD (Data Carrier Detect) RXD# (Receive Data) TXD# (Transmit Data) DTR (Data Terminal Ready) Ground DSR (Data Set Ready) RTS (Request To Send) CTS (Clear To Send) RI (Ring Indicator)
Intel Desktop Board D510MO Technical Product Specification Table 15. LVDS Panel Voltage Selection Jumper (Optional) Voltage Jumper Setting Configuration 3.3 V 2 and 4 Jumper position for 3.3 V (default) 6 and 4 Jumper position for 5 V 12 V...
Technical Reference Table 18. LVDS Inverter Power Connector (Optional) Signal Name Description Ground Ground 5 V/12 V Inverter power 5 V/12 V Inverter power INV_RATING Inverter rating BKLT_PWM Backlight PWM BKLT_EN Backlight enable Table 19. LVDS Inverter Power Voltage Selection Jumper (Optional) Voltage Jumper Setting Configuration...
Intel Desktop Board D510MO Technical Product Specification Table 20. Parallel Port Header Standard Signal Name ECP Signal Name EPP Signal Name STROBE# STROBE# WRITE# AUTOFD# AUTOFD#, HOSACK DATASTB# FAULT# FAULT#, PERIPHREQST# FAULT# INT# INT#, REVERSERQST# RESET# SLCTIN# SLCTIN# ADDRSTB# GROUND...
Signal Name +5 VDC +5 VDC Ground Ground KEY (no pin) No Connect Table 26. Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support) Signal Name Signal Name +5 VDC Ground KEY (no pin) LED#...
Intel Desktop Board D510MO Technical Product Specification 2.2.2.2 Add-in Card Connectors The board has the following add-in card connectors: • PCI Express x1 Mini Card (rev 1.2 compliant) connector • PCI Conventional (rev 2.3 compliant) bus connector Note the following considerations for the PCI Conventional bus connector: •...
Technical Reference 2.2.2.4 Front Panel Header This section describes the functions of the front panel header. Table 28 lists the signal names of the front panel header. Figure 11 is a connection diagram for the front panel header. Table 28. Front Panel Header Signal Description Signal...
• SATA storage device connected to an onboard SATA connector • Intel Z-U130 USB Solid State Drive (or compatible device) connected to the designated Z-U130 front panel USB header 2.2.2.4.2 Reset Switch Header Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open.
Use only a front panel USB connector that conforms to the USB 2.0 specification for high-speed USB devices. Figure 12. Connection Diagram for Front Panel USB Header Figure 13. Connection Diagram for Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive, or Compatible Device, Support)
Intel Desktop Board D510MO Technical Product Specification BIOS Configuration Jumper Block CAUTION Do not move the jumper with the power on. Always turn off the power and unplug the power cord from the computer before changing a jumper setting. Otherwise, the board could be damaged.
Technical Reference Table 30. BIOS Configuration Jumper Settings Function/Mode Jumper Setting Configuration Normal The BIOS uses current configuration information and passwords for booting. 3 2 1 Configure After the POST runs, Setup runs automatically. The maintenance menu is displayed. 3 2 1 Recovery None The BIOS attempts to recover the BIOS configuration.
Intel Desktop Board D510MO Technical Product Specification Mechanical Considerations 2.4.1 Form Factor The board is designed to fit into a mini-ITX or microATX form-factor chassis. Figure 15 illustrates the mechanical form factor for the board. Dimensions are given in inches [millimeters].
Failure to ensure appropriate airflow may result in reduced performance of both the processor and/or voltage regulator or, in some instances, damage to the board. For a list of chassis that have been tested with Intel Desktop Boards please refer to the following website: http://developer.intel.com/design/motherbd/cooling.htm...
Page 58
Intel Desktop Board D510MO Technical Product Specification CAUTION Ensure that proper airflow is maintained in the processor voltage regulator circuit. Failure to do so may result in damage to the voltage regulator circuit. The processor voltage regulator area (shown in Figure 16) can reach a temperature of up to 85 C in an open chassis.
This information should be used in conjunction with the Thermal/Mechanical ® Specifications and Design Guidelines (TMSDG) published for Intel Atom™ D400 and D500 Series processors. The TMSDG contains detailed package information and thermal mechanical specifications for the processors.
Technical Reference Figure 17. Fan Location Guide for Cassis Selection (Chassis Orientation is Not Restricted) For all chassis configurations, the heatsink performance parameter, Ψ should be less than 3.85 °C/W. The detail thermal measurement metrology is described in the TMSDG. For chassis that fail to meet the thermal specifications guideline highlighted above, an actively cooled heatsink solution should be used.
• 3.5-inch SATA hard disk drive, running Microsoft Windows Vista Home Basic ⎯ Load: continuous read/write benchmark • Intel Z-U130 USB Solid-State Drive (or compatible device) on the USB flash drive header ⎯ Load: continuous read/write benchmark • Wireless card on PCI Express Mini Card slot, connected via 802.11n protocol ⎯...
Prediction Procedure, TR-NWT-000332, Issue 4, September 1991. The MTBF prediction is used to estimate repair rates and spare parts requirements. The MTBF data was calculated from predicted data at 55 ºC. The Intel Desktop Board D510MO MTBF is 248,232.584 hours.
Intel Desktop Board D510MO Technical Product Specification Environmental Table 35 lists the environmental specifications for the board. Table 35. Intel Desktop Board D510MO Environmental Specifications Parameter Specification Temperature Non-Operating -20 °C to +70 °C Operating 0 °C to +50 °C...
Overview of BIOS Features Introduction The board uses an Intel BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated using a disk-based program. The SPI Flash contains the BIOS Setup program, POST, the PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
Intel Desktop Board D510MO Technical Product Specification Table 36 lists the BIOS Setup program menu features. Table 36. BIOS Setup Program Menu Bar Maintenance Main Advanced Security Power Boot Exit Clears Displays Configures Sets Configures Selects boot Saves or passwords and...
Overview of BIOS Features System Management BIOS (SMBIOS) SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in a managed network. The main component of SMBIOS is the Management Information Format (MIF) database, which contains information about the computing system and its components.
Legacy USB support from the BIOS is no longer used. 7. Additional USB legacy feature options can be accessed by using Intel Integrator Toolkit. To install an operating system that supports USB, verify that Legacy USB support in the BIOS Setup program is set to Enabled and follow the operating system’s...
Overview of BIOS Features BIOS Updates The BIOS can be updated using either of the following utilities, which are available on the Intel World Wide Web site: ® • Intel Express BIOS Update utility, which enables automated updating while in the Windows environment.
Integrator’s Toolkit that is available from Intel can be used to create a custom splash screen. NOTE If you add a custom splash screen, it will share space with the Intel branded logo. Refer to For information about Intel Integrator Toolkit http://developer.intel.com/design/motherbd/software/itk/...
Overview of BIOS Features 3.7.3 Booting Without Attached Devices For use in embedded applications, the BIOS has been designed so that after passing the POST, the operating system loader is invoked even if the following devices are not present: • Video adapter •...
Intel Desktop Board D510MO Technical Product Specification BIOS Security Features The BIOS includes security features that restrict access to the BIOS Setup program and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup program and for booting the computer, with the following restrictions: •...
Board Status and Error Messages BIOS Beep Codes Whenever a recoverable error occurs during POST, the BIOS causes the board’s speaker to beep an error message describing the problem (see Table 41). Table 41. BIOS Beep Codes Type Pattern Frequency F2 Setup/F10 Boot Menu One 0.5 second beep when BIOS is ready to 932 Hz...
Intel Desktop Board D510MO Technical Product Specification Front-panel Power LED Blink Codes Whenever a recoverable error occurs during POST, the BIOS causes the board’s front panel power LED to blink an error message describing the problem (see Table 42). Table 42. Front-panel Power LED Blink Codes...
Board Status and Error Messages Port 80h POST Codes During the POST, the BIOS generates diagnostic progress codes (POST codes) to I/O port 80h. If the POST fails, execution stops and the last POST code generated is left at port 80h. This code is useful for determining the point where an error occurred. Displaying the POST codes requires a PCI bus add-in card, often called a POST card.
Page 76
Intel Desktop Board D510MO Technical Product Specification Table 45. Port 80h POST Codes POST Code Description of POST Operation Host Processor Power-on initialization of the host processor (Boot Strap Processor) Host processor cache initialization (including APs) Starting Application processor initialization...
Page 77
Board Status and Error Messages Table 45. Port 80h POST Codes (continued) POST Code Description of POST Operation Keyboard (PS/2 or USB) Resetting keyboard Disabling keyboard Detecting presence of keyboard Enabling the keyboard Clearing keyboard input buffer Instructing keyboard controller to run Self Test (PS/2 only) Mouse (PS/2 or USB) Resetting mouse Disabling mouse...
Page 78
Intel Desktop Board D510MO Technical Product Specification Table 45. Port 80h POST Codes (continued) POST Code Description of POST Operation DXE Drivers Waiting for user input Checking password Entering BIOS setup Calling Legacy Option ROMs Runtime Phase/EFI OS Boot Entering Sleep state...
Electromagnetic Compatibility (EMC) standards • Product certification markings 5.1.1 Safety Standards Intel Desktop Board D510MO complies with the safety standards stated in Table 47 when correctly installed in a compatible host system. Table 47. Safety Standards Standard Title CSA/UL 60950-1, First Edition Information Technology Equipment –...
European Union Declaration of Conformity Statement ® We, Intel Corporation, declare under our sole responsibility that the product Intel Desktop Board D510MO is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directive 2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).
恰当的重复使用处理。 请参考http://www.intel.com/intel/other/ehs/product_ecology 了解此计划的详情,包括涉及产品之范围、回收地点、运送指导、条款和条件等。 Deutsch Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für ordnungsgemäßes Recycling zurückzugeben. Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte, verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der...
Page 84
Français Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en œuvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits usés en les retournant à...
Page 85
RoHS Directive 2002/95/EC) compliant product. EU RoHS restricts the use of six materials. One of the six restricted materials is lead. This Intel Desktop Board is lead free although certain discrete components used on the board contain a small amount of lead which is necessary for component performance and/or reliability.
Intel Desktop Board D510MO Technical Product Specification Table 48. Lead-Free Board Markings Description Mark Lead-Free 2 Level Interconnect: This symbol is used to identify electrical and electronic assemblies and components in which the lead (Pb) concentration level in the board substrate and...
Regulatory Compliance and Battery Disposal Information 5.1.4 EMC Regulations Intel Desktop Board D510MO complies with the EMC regulations stated in Table 49 when correctly installed in a compatible host system. Table 49. EMC Regulations Regulation Title FCC 47 CFR Part 15,...
China RoHS/Environmentally Friendly Use Period Logo: This is an example of the symbol used on Intel Desktop Boards and associated collateral. The color of the mark may vary depending upon the application. The Environmental Friendly Usage Period (EFUP) for Intel Desktop Boards has been determined...
Regulatory Compliance and Battery Disposal Information Battery Disposal Information CAUTION Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations. PRECAUTION Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect.
Page 90
Intel Desktop Board D510MO Technical Product Specification PRECAUCIÓN Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante.
Page 91
Regulatory Compliance and Battery Disposal Information AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan. OSTRZEŻENIE Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii.