Nextar Q3 Owner's Manual

Q3 hardware manual
Hide thumbs Also See for Q3:

Advertisement

Important Safety
Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.
POWER SUPPLY:
Connect the supplied adapter to the side of the unit in the slot marked "Power In". Plug
the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty
inserting the plug, turn it over and reinsert it. If the unit will not the used for a long time,
disconnect the plug from the outlet.
NOTE:
Before plugging the power cord into an AC outlet, make sure that all the connections
have been made.
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Refer to service manual for servicing instructions.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Q3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Nextar Q3

  • Page 1: Important Safety Instructions

    Important Safety Instruction CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.
  • Page 2 Important Safety Instructions NOTES Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a damp cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
  • Page 3: Features

    Features Navigation Function Navigation Function: The unit is designed to provide you with route suggestions. It supports voice navigation. Other Special Functions Power Adapter Switch: Automatically SD Card and USB Input: unit is designed adapts to voltage requirements in U.S and with SD card and USB ports, can be other countries.
  • Page 4: Accessories

    Accessories Accessories List ITEM NAME Remote Control (with battery) Owner’s Manual Power Adaptor Car Adaptor USB Cable Windshield mount bracket Mounting cradle Dashboard mount disk Pouch NOTE Accessories and their part numbers are subject to modification without prior notice due to improvements.
  • Page 5: Table Of Contents

    Contents Important Safety Instructions …………………………………………..1 …………………………………………...3 Features …………………………………………...4 Accessories …………………………………………...6 View of Main Unit ……………………………………….…..8 Remote Control …………………………………………..9 System Connections Power Supply Preparation …………………………………………..11 General Setup …………………………………………..13 Playing Music …………………………………………..16 Using the Mounting Bracket ………………………………………..…19 Troubleshooting …………………………………………..20 Specifications …………………………………………..21...
  • Page 6: View Of Main Unit

    View of Main Unit Front View MENU button Press to enter the main menu. Speakers Charge Indicator When charging the battery, it is red; When the battery is fully charged, it turns green. POWER button Press the POWER button to enter or exit the standby mode. LCD Screen Remote Sensor Receive signal from remote control for operation.
  • Page 7: Side View

    View of Main Unit Side View Card Port Insert the SD/MMC card into the port. USB port Used to connect to the USB device. Volume Control Used to adjust the volume of the headphone and speaker. Headphone Jack Used to connect headphones for private listening.
  • Page 8: Remote Control

    Remote Control POWER button Press to enter or exit standby mode. direction buttons Press to select items in the setup menu. direction buttons Press to adjust items in the setup menu. OK button Press to confirm selection. MENU button Press to enter the main menu. - button Press to zoom out the map.
  • Page 9: System Connections

    PC etc. See the below figure for details: 1. You should install the driver into your PC first. You can download the driver (MSASYNC) via the Internet from web site: http://www.nextar.com 2. Turn on the unit.
  • Page 10 System Connections Inserting SD Card The unit is designed with SD/MMC Card jack which allows you to insert the SD/MMC card into the unit as shown below: Connecting to Headphones Connect the headphones to the right side of the unit for private listening. When headphone is connected, the speakers will automatically turn off.
  • Page 11: Power Supply Preparation

    Power Supply Preparation Using the AC Adaptor The player is supplied with an AC adaptor for powering the unit and charging the battery. Connect AC adaptor to the right side of the player in the jack marked DC 5V IN, as shown on the right. Plug the two-prong end of the power cord into a grounded electrical outlet.
  • Page 12: Charging The Battery Pack

    Power Supply Preparation About Rechargeable Battery Your portable GPS player comes with a built-in rechargeable battery. Charge the battery fully before initial use. Charging time is normally about 3.5 hours. A fully charged battery delivers about 3 hours of use. Working conditions and precautions for the rechargeable battery New batteries should be fully charged before initial use.
  • Page 13: General Setup

    General Setup General Setup When turn on the unit, the screen will display the main menu for about 3~5 seconds and then enter the warning menu, as shown below: Tap I Agree to enter the map view. Press the MENU button to return to the main menu. In the main menu, there are three items for selecting, touch the corresponding item to enter it.
  • Page 14 General Setup Backlight in the main menu to enter the backlight settings menu, as shown below: Tap the buttons to adjust the brightness, tap to confirm and tap to cancel. Date & Time in the main menu, the screen will display as below: buttons to select time zone, tap buttons to set the date and time, tap the button to return.
  • Page 15 General Setup Power in the main menu, the screen will display as below: The menu will display the battery status. Tap the button to return. Screen in the main menu, the screen will display as below: Tap the + button as it moves around the screen, then the + will disappear and tap the screen to return to the settings menu.
  • Page 16: Playing Music

    Playing Music Note: Do not store MP3 or WWA format files in the Flash storage, for the flash storage is used to store map data, in order to avoid the misoperation which can result in the map data missing and lost. The unit is designed with SD/MMC card slot.
  • Page 17 Playing Music In the menu, if there are no songs in the playlist, tap the button to add songs into the playlist. The screen will display as below: Double tap MMC_Storage to open the folder, the songs in the folder will be displayed on the screen.
  • Page 18 Playing Music During playback, tap button to go to the previous track. During playback, tap button to go to the next track. During playback, tap button to pause playback, or in stop status, tap the button to resume playback. During playback, tap button to stop playback.
  • Page 19: Using The Mounting Bracket

    Using the Mounting Bracket When using the unit in vehicle, you can use the supplied mounting assemblies (mounting bracket, mounting cradle and dashboard mount disk) to mount the unit in the vehicle. Take the following steps to operate: Slide the mounting cradle onto the end of the mounting bracket. Set the bottom edge of the unit on the bottom of the mounting cradle.
  • Page 20: Troubleshooting

    Troubleshooting Take steps described in the tables below to solve simple problems before contacting customer service. If you suspect something wrong with this unit, immediately turn the power off and disconnect the power connector from the unit. Never try to repair the unit yourself because it is dangerous to do so.
  • Page 21: Specifications

    Specifications Frequency Response 20Hz 20kHz Audio Signal-to-noise Rate 65dB Audio distortion or noise 20dB (1kHz) Channel Separation 70dB (1kHz) Dynamic Range 80dB (1kHz) Power AC 100-240V 50/60Hz < Dimensions 130mmX74mmX24mm (L*W*D) DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE...
  • Page 22 © 2008 Nextar (Hong Kong) Limited. Nextar is a trademark and service mark of Nextar (Hong Kong) Limited. All other brand names, trademarks and service marks are property of their owners. Nextar may find it necessary to modify, amend or otherwise change or update this manual.

Table of Contents