Summary of Contents for LG L1718S-BN - - 17" LCD Monitor
Page 1
Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : MODEL: L1718S (L1718S-SNQ/L1718S-BNQ.Axx*EP) xx* means sales region and Module (xxK : INNOLUX, xxB : CPT) CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. *To apply the MSTAR Chip.
PRECAUTION WARNING WARNING FOR THE SAFETY-RELATED COMPONENT. BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and inverter circuit, must disconnect the AC adapter...
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in service manual and its supplements and addenda, read this service manual. and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap publication.
Page 5
General Soldering Guidelines Replacement 1. Carefully insert the replacement IC in the circuit board. 1. Use a grounded-tip, low-wattage soldering iron and 2. Carefully bend each IC lead against the circuit foil pad appropriate tip size and shape that will maintain tip and solder it.
Page 6
Circuit Board Foil Repair At Other Connections Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper circuit board will weaken the adhesive that bonds the foil to pattern at connections other than IC Pins. This technique the circuit board causing the foil to separate from or involves the installation of a jumper wire on the component side of the circuit board.
TIMING CHART VIDEO SYNC Front Back distingis Polo Resolutio Frequency Total period Display Sync. CLOCK Porch Porch [kHz]/ [Hz] hment rity [MHz] 25.175 31.469 H(Pixels) 640 x 350 V(Lines) 70.08 H(Pixels) 28.321 31.468 720 X 400 V(Lines) 70.09 H(Pixels) 25.175 31.469 640 x 480 V(Lines)
BLOCK DIAGRAM InnoLux TFT-LCD Module with 4FFCLs LVDS Transmitter 128KB Flash ROM Inverter + TSUM16AL-LF DC12V to DC5V EEPROM 24C04 3.3V and OSD parameter 1.8V regulator AC Socket Timing 24C02 parameter D-sub AC Input Analog Key pad RGB Signal...
DESCRIPTION OF BLOCK DIAGRAM 1. Video Controller Part. This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixel clock. The pixel clock for each mode is generated by the PLL. The range of the pixel clock is from 25MHz to 135MHz.
LIPS Board Block Diagram 50~60Hz HVDC HVDC 66KHz 66KHz INPUT REXTIFIER INPUT REXTIFIER ENERGY ENERGY OUTPUT RECTIFIER OUTPUT RECTIFIER COMPONENTS COMPONENTS AND FILTER AND FILTER TRANSFER TRANSFER AND FILTER AND FILTER LINE LINE 100~240V 100~240V PHOTO-COUPLER PHOTO-COUPLER SIGNAL SIGNAL COMTROL COMTROL ISOLATION ISOLATION...
ADJUSTMENT Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
SERVICE OSD 1) Turn off the power switch at the front side of the display. 2) Wait for about 5 seconds and press MENU, POWER switch with 1 second interval. 3) The SVC OSD menu contains additional menus that the User OSD menu as described below. a) Auto Color : W/B balance and Automatically sets the gain and offset value.
TROUBLESHOOTING GUIDE 1. No Power & Power LED Off No power Check IC802, Check circuit Check primary C805, T801 if short rectifier voltage Check F801, P801, D801 Check pin3 of Check R801, R805, IC802 voltage R822, R823, R817 about 1V Check R803, R807, Check pin2 of IC802 R824, R825...
Page 16
2. Backlight can’t be turned on No raster? LED Green? Backlight can’t be turned on. Is there 5Vdc voltage on Check power supply pin2 of IC501? Is there high-level Is Ok R526? voltage on pin10 of IC501? Check I/F board R526 open Connecting the Are connected rightly CN501,...
Page 17
3. DC output voltage is unstable Output Voltage Unstable Check Check ZD801, Check circuit if ZD802, ZD803, Q801 below 0.3V short D803, D805 Check Q801, Q802 Check Pin R of Check R809, Check reference R814, IC801, IC803 voltage voltage R818 about 2.5V Check R810, R811 Check...
Page 18
4.Output power is unstable Unstable power Check R810, Check sampling R811, R818 Circuit Change R810, R811, Check the C Check the R pin pin voltage voltage of IC803 Change of IC803 if IC803 about 2.5V Check R809, R808, R814, D809 Check pin1 of Check D806, C815 if IC802 voltage...
Page 19
5.Black Screen and backlight turn on Black Screen Check power supply: Power Fail Pin1, 2 of CN101 Check FB103 Check pin34, 51, 66, and 82 And U102 Of U105 Check FB106 Check pin32, 49, 56, and 75 And U101 Of U105 Check Reset (pin84) Check C144, R172 Of U105...
Page 20
6.White Screen White Screen LVDS Cable Workmanship Reinsert Change LVDS LVDS Cable NG Cable Check VLCD Check LVDS Panel Fail Is 5V? Signals Check Panel - Enable Check the HW Reset Check C144 Of U105 (pin48) is High? Of U105 pin84 R172 Check R168, R105 Q103, Q101...
7. BAD SCREEN Bad Screen LVDS Cable Reinsert Workmanship Change LVDS Cable LVDS Cable NG Check Crystal:Pin96,97 Check :X101, Of U105 C153,C154 Check the communication Check: SDO,SCZ, Of U105 and U106 SCK,SDI, Reset Check the pins of U105 and U106...
Page 29
419342253670R C SMD(0805) Y5V 2.2uF/25V Z RoHS C507,C511, 419311040060R C SMD(0603) X7R 0.1uF/50V K RoHS C821, 419316830060R C SMD (0603) X7R 0.068uF 50V,K RoHS C510, 419316810070R C SMD(0805) X7R 680PF/50V K,RoHS C523,C530, 419304710560R C SMD(0603) NPO 470PF/50V,J,RoHS C529, 419311020060R C SMD(0603) X7R 1000PF/50V K RoHS C504, 419314720060R C SMD(0603) X7R 4700PF/50V K RoHS...