Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-42 FACTORY MODEL: LB700K MODEL: L1710B (LB700K-GU) L1710B (LB700K-GD) ) ID LABEL MODEL No. CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Signal Connector Pin Assignment • DVI-I Connector (Digital/Analog) Signal (DVI-I) Signal (DVI-I) T. M. D. S. Data2- Hot Plug Detect T. M. D. S. Data2+ T. M. D. S. Data0- T. M. D. S. Data0+ T. M. D. S. Data2/4 Shield T.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Total Period Back Porch Video Active Time Front Porch Sync Duration Sync Mode Resolution Frequency Clock Sort Polarity 31.469 640x350 25.175 70Hz...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW D-Sub Signal Connect DVI Connect USB Port See Front Control Panel Power Connect Front Control Panel 1. Power ON/OFF Button Button Use this button to turn the monitor on or off. Use these buttons to choose or adjust items in the On Screen Display.
Making use of USB (Universal Serial Bus)* USB (Universal Serial Bus) is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other to your monitor instead of having to connect them to your computer.
DESCRIPTION OF BLOCK DIAGRAM 1. Input signal switching part. There are two inputs which are analog and digital analog input. They come from each 15 pin D-Sub and 24 pin DVI-I connector. 2. Video Controller Part. This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixelclock.
LIPS Board Block Diagram 50 ~ 60Hz 100KHz HVDC INPUT RECTIFIER ENERGY OUTPUT RECTIFIER COMPONENTS AND FILTER TRANSFER AND FILTER LINE 100 ~ 240V SIGNAL PHOTO- COLLENTI CONTROL COUPLER CIRCUIT ISOLATION PRIMARY SECONDARY High Voltage output INVERTER CIRCUIT Operation description_LIPS 1.
ADJUSTMENT All adjustment are thoroughly checked and corrected 2. Adjustment for White Balance when the monitor leaves the factory, but sometimes 1) Display Black pattern at SXGA/60Hz. 2) Select COLOR → BIAS CALIBRATION command several minor adjustment may be required. Adjustment should be following procedure and after and Enter.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK J702 TROUBLE IN INPUT VOLTAGE LIPS (POWER) (12V) ? CHECK J702 TROUBLE IN 5V VOLTAGE LIPS (POWER) (5V) ? CHECK U203’s PIN 151. TROUBLE IN IS THIS PIN U203 or X201 OSCILLATED? TROUBLE SOMEWHERE ELSE...
Page 15
2. NO RASTER NO RASTER CHECK J702 PIN 1, 2, 5, 6 TROUBLE IN (12V/ 5V) ? LIPS CHECK TROUBLE IN J705 PIN 28, 29, 30 U802 (5V) ? CHECK TROUBLE IN U801 U801 (3.3V)? CHECK TROUBLE IN U201(GM5120) ? U201 CHECK TROUBLE IN...
Page 17
3. NO CLOCK (CLOCK GENERATOR) NO DOT CLOCK CHECK TROUBLE IN X201 20MHz ? X201 CHECK TROUBLE IN R237 U201 CLOCK ? - 17 -...
Page 18
4. TROUBLE IN DPM TROUBLE IN DPM CHECK CHECK PC R711, R712 PC IS NOT GOING (SYNC) ? INTO DPM OFF MODE CHECK U203 PIN 152 TROUBLE IN WAVEFORM X201 (20MHz) ? CHECK TROUBLE IN U203 PIN 44 SIGNAL CABLE (0V) ? TROUBLE IN PC - 18 -...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2002. 10. 17. DATE: 2002. 10. 17. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.