Panasonic TH-65PF12EK Operating Instructions Manual page 53

Item
Off
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 14).
• Signal can be displayed when the Terminal board is installed.
INPUT lock
• Input switch can be used when this is set to "Off".
• In two screen display mode, if anything other than "Off" is set, the value will be fi xed as the value input
in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal.
(Ex. INPUT1A, INPUT1B)
Off
Off: All the buttons on main unit can be used.
MENU&ENTER: Locks
On: Locks all the button on main unit.
Button lock
Sets Button lock with the unit buttons in the following procedure.
Off: Press
MENU&ENTER: Press
On: Press
Off
Off: You can use all of the buttons on the remote control.
User1: You can only use
Remocon User level
User2: You can only use
User3: Locks all the buttons on remote control.
Enable: Enables the "Off-timer function".
Disable: Disables the "Off-timer function".
Off-timer function
Note: When "Disable" is set, the Off-timer is cancelled.
Normal
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Initial Power Mode
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Note: When using multiple displays, "Standby" is preferred to be set in order to reduce a power load.
Sets panel ID number when panel is used in "Remote ID" or "Serial ID".
Set value range: 0 - 100
ID select
(Standard value: 0)
The setting of this menu is valid only when using ID remote control.
Off: Disables ID remote control functions. You can use normal remote control operations.
On: Enable ID remote control functions.
Remote ID
Note: To use the ID remote control function, it is necessary to set each ID number of remote control and display unit.
Sets the panel ID Control.
Off: Disables external control by the ID.
Serial ID
On: Enables the external control by the ID.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Notes:
Display size
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD)) 525i,
525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,
1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom, Multi display or Portrait display is
selected.
• When "Display size" is set to "On", "H-Pos" and "V-Pos" in "Pos. /Size" can be adjusted.
• Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals.
PC INPUT1 INPUT2
MENU&ENTER On
and
MENU ENTER/
four times→Press
four times→Press
ENTER/
four times→Press
User1 User2
, ,
button on the remote control.
Standby On
Power returns in power On. (Power Indicator : green)
About the setting method, please refer to "ID Remote Control Function" (see page 42) and "ID
select" (above-mentioned).
Off
Adjustments
INPUT3
buttons on main unit.
four times→Press four times→Press
INPUT
four times→Press
four times→Press four times→Press
ENTER/
User3
, , buttons on the remote control.
On
Options Adjustments
ENTER/
four times→Press
INPUT
ENTER/
ENTER/
53