Maytag MEDB850WB - 29" Electric Dryer Use And Care Manual page 9

You can change Sensor and Timed C ycles, Modifiers, and Options
anytime before p ressing Start.
• Three s hort tones s ound i fanunavailable combination is
selected. The last s election willnotbeaccepted.
Changing Cycles after pressing Start
1. Press POWER/CANCEl ....
2. Select the desired cycle and options.
3. Press START/PAUSE. The dryer starts at the beginning of the new
cycle.
NOTE: If you do not press Start/Pause within 5 minutes of selecting
the cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change an Option or Modifier anytime before the selected
Option or Modifier begins.
1. Press START/PAUSE.
2. Select the new Option and/or Modifier.
2,. Press START/PAUSE to continue the cycle.
Changing the Preset Dryness Level Settings
If all of your loads on all Sensor cycles are consistently not as dry as
you would like, you may change the preset Dryness I_eve[ settings to
increase the dryness. This change will affect all of your Sensor
cycles.
Your Dryness I_eve[ settings can be adjusted to adapt to different
installations, environmental conditions, or persona[ preference.
There are 3 drying settings: 1 (factory preset dryness [eve[), 2 (slightly
dryer clothes, approximately 15% more drying time) and 3 (much
dryer clothes, approximately 30% more drying time).
1. The Dryness I.eve[ settings cannot be changed while the dryer is
running.
2. Press and hold the DRYNESS I.EVEL button for 5 seconds. The
dryer will beep, and "CF" will be displayed for 1 second
followed by the current Dryness I_eve[ setting.
3. To select a new I)ryness Level setting, press the DRYNESS LEVEl ....
button again until the desired Dryness I.eve[ setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START/PAUSE to save the Dryness I_eve[ setting.
The Dryness I_eve[ setting you selected will become your new preset
Dryness I.eve[ setting for all Sensor cycles.
I I.l l,l.I I,,. I _ < I .....
Use the Drying Rack to dry items such as sweaters and pillows
without tumbling. The drum turns, but the drying rack does not
move.
If your mode[ does not have a drying rack, you may be able to
purchase one for your model. To findout whether your model allows
drying rack usage and for information on ordering, please refer to the
front page of the manual or contact the dealer from whom you
purchased your dryer.
NOTE: The drying rack must be removed for normal tumbling. Do
not use the automatic cycle with the drying rack.
To use the drying rack
1. Open dryer door.
A
2.
A. f)'ont edge
Place drying rack inside dryer drum, positioning the back wire
on the [edge of the inner dryer back pane[. Push down on front
edge of drying rack to secure at the front of the dryer.
B
A. Drying rack h'ont edge
B. Dryer back panel
3. Put the wet items on top of the drying rack. I.eave space between
the items so air can reach all the surfaces.
NOTE: I)o not allow items to hang over the edge of the drying rack.
I
4.
5.
6.
7.
Close the door.
Press the POWER/CANCEl_ button.
Select a Timed Dry cycle and temperature (see following chart).
Items containing foam, rubbe_; or plastic must be dried on a
clothesline or by using the Air Fluff temperature setting.
You must select a time by pressing TIME ADJUST + (plus) or -
(minus). Reset time as needed to complete drying. Refer to the
following table.
8. Press START/PAUSE.