Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided. ViewSonic Corporation Confidential – Do Not Copy VG800b...
2. General Description (Quick Reference) 3. Electrical Characteristics 4. Mechanical Characteristics 5. Packaging 6. Environmental Characteristics 7. Factory Setting for Shipment Appendix I (Preset Signal Timing) Appendix II (EDID Code) Appendix III (Label printing) ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 6
(Active display area is dependent upon signal timings) Power Supply AC adapter input AC90V-264V 50 / 60 Hz Rating DC input DC 12V AC Power On mode Consumption less than 3W Off mode( w/o audio cable connected ) ViewSonic Corporation Confidential – Do Not Copy VG800b...
AC power cord-Schuko 1.8m Analog VGA cable 1.8m Audio cable 1.8m Viewsonic CD-Wizard Regulatory UL, CSA or cUL, CB Report, CE, FCC-B, DOC-B, TUV/Ergo Standards (which covers ISO13406-2 and MPRIII), TUV/GS, PCT (GOST-R) with 20 Hygienic certificates, PCBC (B Mark), SEMKO, DEMKO, FIMKO, NEMKO, BSMI, VCCI, CCIB/EMC, CCEE, PSB (Singapore Safety), TCO’95, NOM and Argentina...
Page 8
3.3.2.2 Line input signal & impedance 1.0 Vrms, 10 kOhm 3.3.2.3 OUTPUT SIGNAL AT SPEAKER TERMINAL @ < 10 % distortion Vp-p(out) >= 5 Vp-p 3.3.2.4 Frequency Response 300 Hz – 20 Khz ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 9
15 pin mini D-sub PIN NO. Separate Sync GREEN BLUE GROUND GROUND GROUND GROUND GROUND GROUND H.SYNC V.SYNC 3.3.3.2 Audio Connector 3.5 mm Stereo jack x 1, 3.5mm Microphone jack x 1 ViewSonic Corporation Confidential – Do Not Copy VG800b...
(@ Cont / Bright max) 3.5. Synchronization Horizontal: 30 to 82 kHz Vertical: 50 to 85 Hz Non-interlaced maximum 75Hz @ 1280 x 1024 mode Recommended 60Hz @ 1280 x 1024 mode ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 11
77 ± 6°F, 25 ± 5°C Viewing angle: AU = 0°, AR = 0° Warm Up time: minimum 30 minutes Measuring instrument: TOPCOM BM-7 Luminance Meter Measuring distance: 500 mm Measuring angle: 2° ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 12
(Note 2) Viewing angle is measured as follows: ’ ’ (Note 3) Definition of response time is as follows: Response time is measured when the display data is changed from white to black. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 13
White Optical Response (Note 4) Judge points for brightness uniformity Brightness uniformity is judged at nine (9) points on display area: Bmin BUNI Bmax Bmax : Maximum Brightness Bmin : Minimum Brightness ViewSonic Corporation Confidential – Do Not Copy VG800b...
Typical Tr = 20ms ; Tf = 10ms Maximum Tr = 30ms; Tf = 25ms Number of Back Light(CCFL) 6 – Edge type back light Backlight (hrs) 60,000 (typ), 50,000 hours Min ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 15
4. Mechanical Characteristics 4.1 Dimensions Net: 436 (W) x 462 (H) x 181 (D) mm Gross: 565 (W) x 525 (H) x 260 (D) mm 4.2 Weight Net: 6.9Kg Gross: 10.6 Kg ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 16
Black (Base color) / Mist White (letter) Size: 41 (W) x 91 (H) mm Location: BOTTOM OF AC ADAPTER Block Copy: DELTA ELECTRONICS,INC. AND ViewSonic Contents: Appendix III 4.4.3 Bar Code Number Label (Carton Box) Material: Art Paper Color: White (Base) / Black (Letter)
Page 17
Production Code : AA YY WW Manufacturing week Last digit of manufacturing year Production Line No. 4.7.2 MCU Revision Label Customer Model No.: VG800 b LCD Panel Supplier : CMO Rev No : P01 ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 18
7.1 OSD Brightness 100%(based on 0-100%) Contrast 80%(based on 0-100%) AutoTune Executed Color Temperature 6500k Volume Balance Bass/Treble OSD Timeout 15 Sec Language English OSD position Center Scaling Fill all 7.2 Power Switch ViewSonic Corporation Confidential – Do Not Copy VG800b...
Appendix I Preset Signal Timings H-Video H active Horizontal H front H back H pulse H total V-Video V active Vertical V front V back V pulse V total ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 23
Appendix II EDID Code analog 100 00 110 00 120 20 Appendix III Label Printing ID LABEL ADAPTER LABEL ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 24
Bar Code label/Serial No Label PCB Assembly Revision Control L18CMW 05ACW(CMO) 0200-001 C10210 MCU Revision Label VG800 b ViewSonic Corporation Confidential – Do Not Copy VG800b...
2 Press the [ ] or [ ] button to scroll to the desired menu option. 3 Press the [2] button to select the menu option. 4 Press the [ ] or [ ] button to select submenu option. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Shortcut: Before displaying the OnView menu, press the [ ] or [ ] button to adjust. Press button [2] to toggle between brightness and contrast. Contrast 1 : Exit 2 : Brightness ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 27
Balance adjusts the proportion of sound coming from each speaker. ] directs more of the sound to the left speaker, [ ] directs more of the sound to the right speaker. Balance 1 : Exit 2 : Select ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 28
Color Adust provides four preset color adjustment: 9300K, 6500K, 5400K, 5000K for improved brightness and color saturation. Press button [2] to select the preset color. Press button ] or [ ] to ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 29
75.0 Model No. VG800b A1PXXXXXXXXX Serial No. Web Site http://www.ViewSonic.com 1 : Exit Manual Image Adjust Manual Image Adjust H/V Position H-Size Fine Tune Sharpness Scaling 1 : Exit 2 : Select ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 30
H-Size adjusts the width of screen image. ] decreases Width of screen image, [ ] increases width of image. H-Size 1 : Exit 2 : Select Fine-Tune Fine-Tune 1 : Exit 2 : Select ViewSonic Corporation Confidential – Do Not Copy VG800b...
1:1 adjusts the video signal so that the height and width of the picture are the same. Scaling Fill Screen Fill Aspect Ratio 1 : Exit 2 : Select Setup Menu Setup Menu Language Resolution Notice OSD Position OSD Timeout OSD Background 1 : Exit 2 : Select ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 32
] moves OSD down, [ ] moves the OSD up. OSD V-Position 1 : Exit 2 : Select OSD Timeout sets the length of time the OnScreen Display screen is displayed before exiting. ViewSonic Corporation Confidential – Do Not Copy VG800b...
* These functions are not available in Digital Mode. Memory Recall is to recall the following functions to factory setting: Contrast, Brightness, H Size, H/V Position, Color Temperature @ 6500K, OSD Position, Sharpness, & OSD Timeout. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 34
OSD Auto Save The OSD shall save new settings when it is turned off by the user or when it times out. There shall not be a separate save. ViewSonic Corporation Confidential – Do Not Copy VG800b...
3.CIRCUIT DESCRIPTION Contents *. Function Block A. Interface Board Power Supply (DC/DC Converter) Micro-Controller Image processor(scalar) LVDS Transmitter DDC 1/2 B Synchronous DRAM B. Audio Board Audio processor AudioAmplifier ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 36
/ RUN pin will vary from 1.19V to 2.4V depending on the load current. Pulling the I / RUN pin up 0.8V(using CM5 and RM2) allows the ICM1 to begin operation. Pin7 (Boost) supply to the topside Floating Drivers. The bootstrap capacitor (CM8) is ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 37
Pin 35 control the brightness of panel Pin36,37 control LED (orange and green) on /off Pin38 control audio board 12V on/off Pin40 control Buzzer on/off Pin41 control ICM3 (regulator)on/off Pin42 control ICM15,16(LVDS Transmitter) on/off. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 38
Horizontal measurements are measured in terms of the selected IFM_CLK (either T_CLK or R_CLK/4), while vertical measurements are measured in terms of HSYNC pulses. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 39
(LVDS) line drivers in a single integrated circuit. These functions allow 28 bits of single-ended low-voltage TTL (LVTTL) data to be synchronously transmitted over five balanced-pair conductors for receipt by a compatible receiver, ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 40
The only user intervention is the possible use of the shutdown/clear (SHTDN) active-low input to inhibit the clock and shut off the LVDS output drivers for lower power consumption. A low-level signal on SHTDN clears all internal registers to a low level. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 41
I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same device to be useful for a variety of high bandwidth, high performance memory PIN DESCRIPTION: ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 42
Selectable input gain are also provided to build a highly effective electronic Audio processor having the highest performance and reliability with the Least external components . and all functions are programable using the IIC BUS ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 43
Of each amplifier is fixed at 20 dB . Pins 1 and 9 are right and left channel inputs respectively. Pins 4 and 6 are right and left channel outputs which connect to two 4 OHM speakers. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 44
Pin 8 is the mute/stand-by Pin 7 is the voltage input for ICA1 ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 48
Check that CM16 positive is at 5V. ( FIG 2.) Check that the voltage level of JM1 is approximately 12V checjk Check JM2 pin1 ICM1 failure LM1,2 failure Adapter failure is12V, pin5 is 5V Inverter failure ICM10 failure ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 49
Check JM2 pin1 is12V, pin5 is 5V Failure point Check ICM17 Pin4is low voltage 1.ICM15,ICM16 failure 2.ICM11 failure Inverter failure ICM10 failure Check ICM17 ICM10 failure Pin5,6,7,8 is About 5V ICM17 failure ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 50
2. Disconnected between JM1 and power cord Check that ICM1 pin5 Failure point Is about 5V LM1,2 failure Check that LM5 Failure point pin 2 is about 5V ICM1 failure Failure point 1.LM5 failure 2.DM1 failure 3.ICM2 failure ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 51
Failure point Check ICA3 pin4,6 is FIG20. 1.ICA1 failure 2.ICM10 failure Check ICA5,ICA6 pin4 is Failure point about 5V 1. QA6 or QA7 failure 2. ICA3 failure ICA5 or ICA6 failure ICM10 failure ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 52
A7. Keypad can not work Check that the signal cable is fully connected between the Inverter and touch board Failure point Failure point 1. ICT1 failure The cable is disconnected 2. LED failure ViewSonic Corporation Confidential – Do Not Copy VG800b...
4. ADJUSTMENT CONTENTS INSTRUMENT ALIGNMENT PREPARATION OF MANUAL ALIGNMENT 2. COLOR TEMPERATURE ALIGNMENT 3. FACTORY PRESET SETTING ViewSonic Corporation Confidential – Do Not Copy VG800b...
1.4.3 Under factory mode, press “1” key. The monitor will exit factory mode and enter normal operation. 1.5 Method to enter/exit manual color alignment menu. Under factory mode, select color temp manual. Item on factory OSD menu. It will display the following color temperature adjust menu. ViewSonic Corporation Confidential – Do Not Copy VG800b...
“DOWN” key to adjust it to meet following Chromaticity SPEC. 9300°K x = 0.283±0.030, y = 0.298±0.030 Y>= 160CD/M 2.1.3 Press “1” to exit 9300 color temperature adjustment and do another color ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 56
5000 color temperature adjustment. 2.4.2 Use “2” to move cursor to R-Driver or G-Driver or B-Driver and then press “UP” or “DOWN” key to adjust it to meet following Chromaticity SPEC. ViewSonic Corporation Confidential – Do Not Copy VG800b...
Page 57
4.2 Press button 2 and down arrow key simultaneously, then press LCD power key. 4.3 In writeable system, key in twelve number or use bar code read in serial number. 4.4 Enter “OUTPUT SN.” 4.5 Pull out adapter. ViewSonic Corporation Confidential – Do Not Copy VG800b...
*Readers Response* Thank you in advance for your feedback on our Service Manual,which allows continuous improvement of our products. We would appreciate your completion of the Assessment Matrix below, for return to ViewSonic corporation Assessment VG800b t i n e l l...
Need help?
Do you have a question about the VG800-2 and is the answer not in the manual?
Questions and answers