Bosch DS835 Installation Instructions

Installation Instructions
for the DS835 Series
TriTech Microwave/PIR Intrusion Detectors
1.0 Specifications
• Dimensions
(HxWxD): 5 in. x 2.8 in. x 2.2 in.
(12.7 cm x 7.1 cm x 5.6 cm)
• Input Power: 9 to 15 VDC, 16 mA DC nominal (up to 48 mA
DC during walk testing or trouble conditions).
Use only an Approved Limited Power
Source.
• Standby Power: No internal standby battery. Standby power
must be provided by an Approved Limited
Power Source. Sixteen mAh required for
each hour of standby time needed.
• Alarm Relay: Silent-operating Normally Closed reed relay.
Contacts rated 3 watts, 125 mA, 28 VDC
maximum for DC resistive loads; and
protected by a 4.7 ohm, ½ watt resistor in the
common "C" leg of the relay. To be connected
to a SELV (Safety Extra-Low Voltage) circuit
only. Do not use with capacitive or inductive
loads.
• Tamper: Normally Closed (with cover on). Contacts
rated at 28 VDC, 125 mA max. To be
connected to a SELV (Safety Extra-Low
Voltage) circuit only. Connect tamper circuit
to a 24-hour protection circuit.
• Temperature Range: -40°F to +120°F (-40°C to +49°C). For UL
Listed requirements, the temperature range
is +32°F to +120°F (0°C to +49°C), indoor
use.
• Microwave Frequency:
DS835: 10.525 GHz (UL Listed)
DS835A: 10.687 GHz (Export only, not UL Listed)
DS835B: 9.9 GHz (Export only, not UL Listed)
• Coverage: 35 ft. by 35 ft. (10.7 m by 10.7 m)
• Internal Pointability: +2° to –10° Vertical, ±10° Horizontal.
• Options: B328 Gimbal Mount Bracket, B335 Low
Profile Swivel Mount Bracket, B338 Ceiling
Mount Bracket
NOTE: Use of a bracket may reduce range and dead zone areas;
not recommended for installations containing pets.
• Compliance: This device complies with Part 15 of the FCC
Rules and with RSS-210 of Industry and
Science Canada. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesirable operation.
Changes or modifications not expressly approved by Bosch Security
Systems can void the user's authority to operate the equipment.
• Reading Bosch Security Systems, Inc. Product Date Codes
For Product Date Code information, refer to the Bosch Security Systems,
Inc. Web site at: http://www.boschsecurity.com/datecodes/
2.0 Installation Considerations
• Never install the detector in an environment that causes an alarm
condition in one technology. Good installations start with the LED
OFF when there is no target motion. It should never be left to operate
with the tricolor LED in a constant or intermittent green, yellow, or
red condition.
• Point the unit away from outside traffic (roads/alleys).
NOTE: Microwave energy will pass through glass and most
common nonmetallic construction walls.
• Avoid installations where rotating machines (e.g. ceiling fans) are
normally in operation within the coverage pattern. Point the unit away
from glass exposed to the outdoors and objects that may change
temperature rapidly.
NOTE: The PIR detector will react to objects rapidly changing
temperature within its field-of-view.
• Eliminate interference from nearby outside sources.
3.0 Mounting
• Select a location likely to intercept an intruder moving across the
coverage pattern. The surface should be solid and vibration-free.
Mounting height range is 6 to 8 ft. (1.8 to 2.4 m). Recommended
mounting height is 6.5 ft. (2 m).
• Remove the cover. Insert a flathead screwdriver into the locking tab
hole at the bottom front of the detector. Pull the cover up and forward.
Wire
Entrances
Terminal
Corner Mount
Strip
Knockout (4)
Bracket Mount
Knockout
Tri-color
LED
LED
Vertical Adjust
Screw Mount
On/Off
Pins
Surface Mount
Knockout (2)
Wire
Vertical
Entrances
Adjust
Screw
Cover Tab and
Locking Screw Hole
• Remove the circuit board from the base. Loosen the Vertical Adjust
Screw and slide the circuit board down, then out.
• Break away the appropriate thin-wall wire entrance and mounting hole
coverings in the base.
• Using the base as a template and aligning it so that the detector will be
mounted with the terminal block at the top and the PIR lens at the
bottom, mark the location of the mounting holes on the mounting
surface. Pre-start the mounting screws.
• Route wiring as necessary. Route to the rear of the base and through
the wire entrance. Make sure all wiring is unpowered before routing.
• Securely attach the base to the mounting surface.
• Return the circuit board to the base and tighten the Vertical Adjust
Screw.
PIR
Sensitivity
Selection Pins
On Look Down Lens
Off
Vertical Adjust
0°
- 4° Scale
- 8°
Face of Lens
(masking area)
MIN MAX
MW
Microwave
Range Adjust