Download Print this page

Kenmore 2718 - High Efficiency 3.1 cu. Ft. Capacity Coin Op Front Load Washer Installation & Use Manual

Coin- operated commercial tumble action washer
Hide thumbs

Advertisement

Quick Links

Coin- Operated Commercial
Tumble Action Washer
PIN 134837400A (0703)
Sears, Roebuck and Co., Hoffman
Estates, IL 60179 U.S.A.
www.sears.com

Advertisement

loading

  Related Manuals for Kenmore 2718 - High Efficiency 3.1 cu. Ft. Capacity Coin Op Front Load Washer

  Summary of Contents for Kenmore 2718 - High Efficiency 3.1 cu. Ft. Capacity Coin Op Front Load Washer

  • Page 1 Coin- Operated Commercial Tumble Action Washer PIN 134837400A (0703) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com...
  • Page 2 Leave these instructions near washer after If you need SERVICE or PARTS for your Kenmore coin-operated washer: be ready to give the model number, serial installation for future reference. number and date of purchase. Record below. NOTE: The electrical...
  • Page 3 Grounding type wall receptacle not use or mix Avoid fire hazard or electrical shock. liquid chlorine bleach with other household chemicals Do not use an adaptor plug extension cord such as toilet cleaners, rust removers, acid products remove grounding prong from electrical power cord.
  • Page 4 PRE-INSTALLATION REQUIREMENTS DRAIN REQUIREMENTS Tools Required for Installation: Models equipped with drain pump: I. 1/4 in. nut driver 2. 3/8 in. socket with ratchet. Drain MUST be capable of eliminating 17 gals (64.3 L) per 3. 3/8 in. open end wrench. minute.
  • Page 5 ROUGH-iN DiMENSiONS ¼,..._ _, 1243,4 J_,, (1.9_ q(62.9) -I-'(2.54) 1½ (3"11) POWER ,CORD SIDE inch (cm) 43/8 (11.2).._> __., -_ _-- (67.9) (7.3) (91.5) WATER INLETS JNDER 3OUNTER (80.3) (87.9) BACK inch (cm)
  • Page 6 UNPACKING Remove the service panel from the front of the washer. Cut the shipping carton along the dotted line along the base of the unit. Remove the 4 nuts and 6 large washers that attach the 2 yellow shipping braces to the drum and the base. Lift up on While in the carton carefully lay the washer on its back the drum and remove the braces (a yellow ribbon surrounds side.
  • Page 7 INSTALLATION Run some water from the hot and cold faucets to flush the 6. Carefully move the washer to its final location. water lines and remove particles that might clog up the water valve screens. NOTE: Do not use the dispenser drawer or door to lift washer. Remove the inlet hoses and rubber washers from the plastic 7.
  • Page 8 Note: If the slide mechanism has already been installed, skip Instructions for Changing Vend Price this step. TOOLS NEEDED Install Coin Slide Medium sized slotted screwdriver * Small slotted Phillips screwdriver 1. Remove the access panel from the top of the meter case by Placeall screws and other items removed from coin slide assembly unlocking the service lock with the key taped to the front of on a cloth so they will not get lost.
  • Page 9 • Pull coin slide out of coin chute (see FIGURE4). STEP6 Set new vend price by adding or removing the appropriate block-out keys and/or dime inserts according to th Table of Vend Prices (see FIGURE7). NOTE: Black colored slots are closed off by block-out key.
  • Page 10 To remove block-out keys, pull straight up. STEP7 Replace coin receiver block into slide: NOTE: Be sure block-out keys and/or dime inserts are seated • Hold coin receiver right side up in the palm of one hand. properly and ratchet dog is in place with irs spring connected (see FIGURE8).
  • Page 11 Meter Case Instructions INSTRUCTIONS TO CHANGE THE NUMBER OF COIN SLIDE INSERTIONS TO START APPLIANCE. 1. Disconnect powerfrom machine. 2. Turn Shaft & Cam Assembly in a clockwise direction until switch lever arm drops into cam notch (Fig. 1). 3. Lift Adjusting Tab away from cam with finger and turn Tab to desired number. Make sure Tab\ locks into place in new position.
  • Page 12 V8 Parts List DESCRIPTION 20-3000 DESCRIPTION 20-3000 DESCRIPTION 20-3000 COIN SIZING BLOCK varies 20-3007 20-3007 00-9724 00-7924 16 SPRING 20-2040 20-2001 SCREW (METRIC) 00-7938 00-7938 17 SPRING PROTECTOR 20-2038 20-2007 PRESSURE SPRING ASM'f 20-1012 20-1012 SCREW (METRIC) TOP HOUSING 20-3019 20-3002 18 RACK 20-2023...
  • Page 13 NEW VEND PRICE Order required parts using this tear-off. Block-out keys will be shipped to you at no charge. Follow product information O _,ii:::_ _i:!? _ ¸_¸¸ i::::O_li, _iiili instructions. To change vend price, detach and mail the lower portion to: Customer Service Department Quantity.
  • Page 14 Notes...
  • Page 15 Notes...
  • Page 16 Your Home For repair- in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances...

This manual is also suitable for:

2718 3.1