ACR Electronics RCL-75 SEARCHLIGHT Product Support Manual
Remote control searchlight system
Hide thumbs
Also See for RCL-75 SEARCHLIGHT:
- Product support manual (20 pages) ,
- Product support manual (20 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ACR Electronics RCL-75 SEARCHLIGHT
Summary of Contents for ACR Electronics RCL-75 SEARCHLIGHT
-
Page 1: Product Support
PRODUCT SUPPORT MANUAL Y1-03-0158 Rev. D RCL-75 Product No. 1946 Remote Control Searchlight System ACR Electronics, Inc. 5757 Ravenswood Road Fort Lauderdale, Fl 33312 +1(954) 981-3333 · Fax +1 (954) 983-5087 www.acrelectronics.com Email: Info@acrelectronics.com A Chelton Group company... -
Page 2: Table Of Contents
TABLE OF CONTENTS FORWARD ......................1 SEARCHLIGHT......................1 UNPACKING THE UNIT ..................2 WIRING ........................4 INSTALLATION ....................4 OPERATION......................7 CARE AND MAINTENANCE................8 BULB REPLACEMENT..................8 SPECIFICATIONS and WARRANTY..............12 10.0 ACCESSORIES.....................13 11.0 TEMPLATES ......................13 Y1-03-0158 Rev. D... -
Page 3: Forward
The RCL-75 Searchlight System contains an intense light beam that produces 180,000 peak candlepower by combining two 55W halogen lamps with our unique optical quality, parabolic reflectors. -
Page 4: Unpacking The Unit
Every effort is made to assure that the RCL-75 has been delivered in good condition. It is important to make sure that all parts are present before you begin installation. (see Figure 3) The RCL-75 Searchlight contains the following: Part Number... - Page 5 FIGURE 3 Y1-03-0158 Rev. D...
-
Page 6: Wiring
WIRING The RCL-75 has two wiring requirements: 1. Connect the remote control to the light 2. Connect the light to 12-volt power with 15 amp rated wiring. The light works best with 13.5 volts. Caution - The connectors on each side of the wire harness are different. Test fit connector to switch before running the harness to the light. - Page 7 Depending on the location selected, your light will need 1/4” diameter stainless steel bolts, nuts, and washers. If mounting area is robust enough panhead lag screws may be used. If the surface area can be reached from the under side, through bolting with lock nuts and washers should be used.
- Page 8 FIGURE 4 5.4.1 Surface Preparation for light Make sure surface is clean and dry. Verify that drill holes will not impact or harm other items (wires, plumbing, hardware or bulkheads). Decide on the use of screws or bolts. Can the backside of mounting surface be reached to install nuts and washers? Note: If the mounting surface is not flat, a special shapeable plate can be purchased, (P/N 9427), to adapt the light base to the surface.
-
Page 9: Operation
FIGURE 5 OPERATION The remote control Point Pad™ is simple to operate. A red LED tells you that power is available. A green LED lights when the light is in use. The ON/OFF button turns the dual beams ON and OFF. The control disk is pushed down in the direction you want to aim the light. -
Page 10: Care And Maintenance
CARE AND MAINTENANCE The RCL-75 is relatively maintenance free. Clean the exterior of the light with a mild detergent and water if desired. Rotate the light left, then right and up then down periodically to keep motors and turning surfaces clean and operational. Caution –... - Page 11 17) Set reflector housing into the swivel sockets with the light pointed down and carefully engage the gear rack. (make sure the drain hole and serial number is facing down). 18) Form the loops in the bulb wires in the same shape as the ones removed. (looking into the back, the gear-toothed rack is on the right and the smooth arch is on the left).
- Page 12 FIGURE 10 FIGURE 11 FIGURE 12 FIGURE 13 FIGURE 14 FIGURE 15 Y1-03-0158 Rev. D...
- Page 13 FIGURE 16 FIGURE 17 FIGURE 18 FIGURE 19 Y1-03-0158 Rev. D...
-
Page 14: Specifications And Warranty
Electronics, Inc. will repair or, at its option, replace at no cost to you for labor, materials or return transportation, provided you obtain a Return Authorization from ACR Electronics, Inc., 5757 Ravenswood Road, Ft. Lauderdale, Fl. 33312-6645. To obtain a Return Authorization, call our Customer Service Department at (800) 432-0227. -
Page 15: Accessories
10.0 ACCESSORIES Here is a list of options and replacement parts that can be ordered for your searchlight. Product Number 1) Mounting riser. 9427 This will raise the searchlight 1" from mounting surface to allow for clearance of deck hardware. It can be shaped to adapt light to uneven surfaces. 2) Replacement bulbs 9403 3) 17' Extension Wire harness...