Table of Contents
Advertisement
SERVI
United States
SALES OFFICES
DOMETIC SALES CORP.
2320 Industrial Pkwy.
Elkhart, IN 46515
Phone 219-295-5226
DOMETIC SALES CORP.
14441 Bonelli St.
City of Industry, CA 91746
Phone 616-966-9431
DOMETIC SALES CORP.
1625-A Rock Mountain Blvd.
Stone Mountain, GA 30083
Phone 404-493-6214
DOMETIC SALES CORP.
7695 S.W. Hunziker Rd.
Portland, OR 97223
Phone 503-620-9510
DOMETIC SALES CORP.
2920 Avenue "E" East
Arlington, TX 76011
Phone 617-277-7211
DOMETIC SALES CORP.
East Oak Ridge Dr.
Rt. 9, Box 17 A
Hagerstown. MD 21740
Phone 301-797-0826
Canada
Euroclean Canada Inc.
Dometic Recreation Division
666 Langs Drive
Cambridge, Ontario
N3H 2N7 Canada
(519) 653-8880
DSC # 303
INSTALLATION
OPERATING INSTRUCTIONS
REFRIGERATOR FOR LP-GAS
ELECTRIC OPERATION.
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don't touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
AND
AND
REFRIGERATOR
RM360
RM460
RM660
RM760
RM1300
Installation
Instructions for use
Gas equipment
Electric equipment
Maintenance
Fault tracing
Door panel
Page
9-10
10
10-11
11
11
12
Advertisement
Table of Contents
Related Manuals for Dometic RM1300
Summary of Contents for Dometic RM1300
- Page 1 SERVI United States SALES OFFICES DOMETIC SALES CORP. 2320 Industrial Pkwy. Elkhart, IN 46515 Phone 219-295-5226 DOMETIC SALES CORP. 14441 Bonelli St. City of Industry, CA 91746 Phone 616-966-9431 DOMETIC SALES CORP. 1625-A Rock Mountain Blvd. Stone Mountain, GA 30083 Phone 404-493-6214 DOMETIC SALES CORP.
- Page 2 REFRIGERATORS WlTH PIEZ0 IGNITER Fig. la Fig. 4a...
- Page 3 REFRIGERATORS WlTH AUTOMATIC IGNITION Fig. 4b.
- Page 4 Fig. 2 Clear blue colour of flame Fig. 3 Gas equipment parts 1. Burner tube 2. Burner housing 3. Burner jet 4. Feeler point (thermocouple) 5. Flame failure safety device 6. Bypass screw 7. Gas/Electric thermostat 6. Pressure test gage connection 9.
-
Page 5: Installation
The flow of combustion and ventilating air must not be obstructed. For ready serviceability of the burner and control manifold parts of the refrigerator the lower side vent is fitted with a iiftout planel which provides an adequate access opening. GAS CONNECTION Hook-up to the gas supply line is accomplished at the manual gas valve, which is furnished with a 3/8”... -
Page 6: Special Hints
Be careful not to damage the sealing strip applied to the floor of the enclosure when the refrigerator is put in place. In the front frame and in the base at the rear of the refrigerator there are holes for screws for fixing the refrigerator in the enclosure. -
Page 7: Certified Installation
The methods of installation are shown in figures 9 and 10. It is essential that all maximum or minimum dimensions are strictly maintained as the performance of the refrigerator is dependent on an adequate flow of air over the rear of the refrigerator. - Page 8 24 11/16632 1/8 RM660 40 13/16623 24 11/166 40 RM760 24 11/166 51 3/16 RM1300 57 15/166 24 15/166 24 11/16 57 1/8 EXAMPLES The clearance N for the RM360 model following way Installation with upper and lower side vents...
-
Page 9: How To Use The Refrigerator
If not repeat the ligh- ting procedure. To shut off the refrigerator turn the knob A to off position. NOTE: As soon as the necessary cold temperature in insi- de the cabinet has been reached, adjust the ther- mostat knob to required setting. -
Page 10: Gas Equipment
To Shut Off the Refrigerator To shut off the refrigerator turn the knob A to off position. If the cabinet is not in operation over a period of weeks, it should be emptied and cleaned and the door left ajar. Some models are provided with interior light, which comes on when the door is opened. -
Page 11: Periodic Maintenance
The electric thermostat is combined with the gas thermostat and is thus operated by the knob B at the front panel. The temperature in the refrigerator can be regulated by turning the thermostat knob to higher or lower numbers. Although the... - Page 12 INSTRUCTIONS FOR MOUNTING THE DOOR PANEL The refrigerator is normally delivered without Before starting the mounting work check that the panel di- mensions are in compliance with those given in the table and read the instructions through. When mounting the panel, pro- ceed as follows.