Binatone ICARUS 1210 User Manual

1 Installation
Icarus 1210 System
You need one battery pack (NiMH, 3.6v, 300mAh) for each handset.
USER GUIDE To fit the batteries
OFFHOOK light
This comes on when Line
1 Open the battery
is off HOOK CHARGE lights
Off when on HOOK compartment cover.
This comes on when
thehandset batteries are
being charged.
PHONE button
Press to begin or answer a SPEAKERPHONE button
2 Insert the plug in the
telephone call.
Press to turn the connector, as shown.
Press to hang up at the end
speakerphone on and off.
Tuck the wires in and lay the
of a call.
battery pack in the
MEMORY button
PLAY / MSG button compartment
Press to make calls to
Direct Message Play numbers stored in memory
VOLUME button
R (Recall) button
Press during a call to
You may need this during a
adjust the volume. 3 Fit the battery compartment
call if your Icarus 1210 is
cover, sliding it into place
INT ( ) button connected to a PBX, or if
and pressing firmly to make
you use BT Select
Press and Hold over 2 sure it is secure
second for Intercom Services
Call.
HANDSET LOCATOR
PROG / LNR button button
When on hook, press to start Press this to make the
programming. handset ring, to help you
find it if you've forgotten
When off hook, press for Last
Warnings
Number Redial where you put it.
Dispose of used batteries safely never try to burn them
or put them anywhere they could get burnt or punctured.
Where is the Handset number? What's the TONE mean ?
When you are not going to use your Icarus 1210 for a few
weeks, take the batteries out so they do not leak
Confirmation Tone : ( =__== ) two short
corrosive substances.
beeps
Do not leave dead batteries in your handset they might
Handset
Error Tone : (======) One long beep
number leak if you do.
1
Low battery Tone : (==) single beep with
long pause (1 mins)
Out of range Tone : (==) single beep
with long pause (12 seconds)
Binatone Help Line: 0845 345 9677 (Local Call rate) Binatone Help Line: 0845 345 9677 (Local Call rate)
2 Making and answering calls 3 Memory dialing
To store a number
To make a call
On Hook Stage
1 Press PHONE or SPEAKER PHONE
or or
1 Press MEM
2 Offhook indication LED blinks slowly
2 Key in the telephone number 3 Key in the memory location (0 to 9)
4 Press MEM again
To answer a call
5 Key in the number (key *,#,0~9, up to 20digits) you
wish to store
1 When the handset and base unit ring, press PHONE or
or or 6
Press MEM again
SPEAKER PHONE
7
Confirmation Tone or Error Tone
RED
To end a call To make a memory call
Off Hook Stage
Press PHONE
1 Press MEM
To redial the last number
2 Offhook indication LED is blinking slowly
1 Press PHONE or SPEAKER PHONE 3 Key in the memory location (0 to 9) that you want to
or or
dial
4
Press LNR Dials out the stored number. [No confirmation tone.]
2
An Error Tone is heard if the memory is empty.
Earpiece Volume
Special error tone
During a phone call, press VOL to cycle through the
If you try to operate an empty memo during online stage, there
different earpiece volume settings.
will be a special error tone heard.
Binatone Help Line: 0845 345 9677 (Local Call rate) Binatone Help Line: 0845 345 9677 (Local Call rate)
To delete a stored number
On hook stage
1 Press MEM
2 Offhook indication LED blinks slowly
3 Key in the memory location (0 to 9)
4 Press MEM again
5
Press MEM again
6 Confirmation Tone or Error Tone
7 Offhook indication LED is OFF
4 Program operation
Dial Mode Setting (P/LNR button function and code * 2 2)
On hook stage
1 Press key P/LNR
2 Offhook indication LED blinks slowly
3 Press digits 2 2
4 Confirmation Tone
5 Press DTMF mode, or # Pulse mode
6 Press key P/LNR
7 Confirmation Tone
Binatone Help Line: 0845 345 9677 (Local Call rate) Binatone Help Line: 0845 345 9677 (Local Call rate)
Change handset ringer volume Base melody volume
1 Press P/LNR key Press the P/LNR button then key in digits 2 1 1
1
2 Key in digits 3 1 1
Melody is on
2
3 Melody On
Press the button to increase the volume up to volume
3
4
Press to increase the volume level 5
5 Press # to decrease the volume
4 Press the # button to decrease the volume down to level 1
or to turn the base ringer off (level 0)
6 Press P/LNR key to confirm setting
5 Press P/LNR button to confirm
7 Confirmation Tone
6
A confirmation can be heard
Change handset ringer melody
Base melody
1 Press P/LNR key
1 Press the P/LNR button then key in digits 2 1 2
2 Key in digits 3 1 2
3 Melody On 2 Melody is on
4 Press button 0~9 to select melody 3 Press button 1~5 to select melody
5 Press P/LNR key to confirm setting 4 Press P/LNR to confirm
6 Confirmation Tone 5 A confirmation tone can be heard
Intercom Calll ( /INT button function )
Low battery tone
1 On Hook Stage
When the battery level is low during a call, you will hear the low battery
2 Press and Hold /INT key tone in the earpiece every minute.
3 You hear the internal call dial tone
4 Press handset number Out of range
When the handset goes out of range of the base unit, you will hear the
5 Ringback tone can be heard
Out of Range Tone in the earpiece every 12 seconds. Y ou must return in
6 Called Handset is ringing range of the base soon otherwise the call will be dropped.
Binatone Help Line: 0845 345 9677 (Local Call rate) Binatone Help Line: 0845 345 9677 (Local Call rate)
Reset the System
1 HS on hook stage
2 Press key P/LNR
3
Offhook indication LED is blinking slowly
4 Key in digits 4 2 1 0
5 Wait until you hear the confirmation tone from HS and BU
6 Both HS and BU are set in default setting
Call Transfer ( /INT button function)
Off hook stage
1 Press and hold /INT to transfer a call.
2 You will hear internal dial tone in the earpiece and the
caller will be on hold.
3
Press Handset number for the call transfer
4
Hear internal ring back tone
5
Once Connected with second handset
6
Press PHONE key to transfer and hang up
OR - press and hold INT key to reconnect to the caller
Binatone Help Line: 0845 345 9677 (Local Call rate)