Binatone AC2000 Manual

AC2000
AC2000
- Press to
select memory
location.
BT Calling
Features.
2. Installation
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
the telephone line cable will reach your telephone line socket or extension socket.
it is not close to a sink, bath or shower, or anywhere else where it might get wet.
it is not close to other electrical equipment - fridges, washing
ovens, TVs, fluorescent lights, etc.
2. Plug the coiled handset
cord into the Handset.
Plug the other end into
the jack on the left
side of the Base unit.
3. Place the Handset in
the Base unit.
make sure the
plugs click
into place.
Always use the
telephone line
cord supplied
4. Plug the telephone line cord
with your
free end into a modular wall jack.
AC2000 phone.
Press the cable into the groove
Other telephone
so that the Base unit stands level.
line cords may
not work.
5. Lift the Handset and check for
Dial tone in the earpiece.
3. Desk/Wall mount installation
installationInstallation
Desk mount
For normal position, as shown below, place
of a desk on any desired but suitable location.
Wall mount
To place the AC2000 phone on a wall,
wall that are 99 mm apart to lay the fixing centers as shown below.
BE CAREFUL to check that there are no
the wall.
Fix two screws at the marked locations, leaving approximately
7mm between the wall and the screw head.
Hang the cradle unit on the screws using the wall mount slots.
You may need to remove the telephone from the wall and tighten
the screws so that the cradle is securely fixed and does not
wobble. Place the Handset on the cradle with the parking hook
on the cradle arranged to fit in the parking recess under the
earpiece on the Handset.
4. Telephone Operation
Timer The AC2000 phone is equipped with a
Display
shows the duration of a call.
The timer will automatically stop after the call has ended.
To display the last outgoing call time;
machines, microwave
1 Lift the Handset.
2 Press TIMER button.
example ' 00:05
To restart/stop the timer during a call;
1 When you dial the telephone number, the timer
start after 7 seconds.
OR
Press TIMER button while the dialled digits are
restart the time.
2 To stop, press TIMER button again.
3 To continue the timer,press TIMER button again.
Making a 1 Lift the Handset, listen for a dial tone.
call
2 Dial the telephone number you wish to call.
10 digits will be shown).
3 To end the call, return the Handset to the Base unit.
Receiving 1
When the phone rings, pick up the Handset to answer the call.
a Call
2 To end the call, return the Handset to the Base unit cradle.
T elephone operation continue...
Last
1 Lift the Handset.
Number
2 Press LAST NUMBER REDIAL/PAUSE button.
Redial
the Base unit on top
(maximum of 48 digits).
Mute
1 During a call, press and hold SECRECY button.
Function
the call cannot hear you but you can hear his side.
2 To get back to the call, release SECRECY button again.
Inserting a For some switchboard systems, an access
Pause in the
(usually an 8 or 9) to
mark two points on the
dialing
Pressing
sequence
after the access number, a
entered,and the desired number can be dialed immediately.
Press
when dialing or storing Long Distance Access Codes.
Use on PBX
If you are using your AC2000 phone on a
user guide tells you to press RECALL;
Press R (RECALL) button on your AC2000 phone.
Slide-back in T elephone operation continue...
electrical wires hidden in
Memory
Storing a Number in Memory
Dialing
1 Lift the Handset.
2 Press STORE button.
3 Enter the telephone number, maximum of 20 digits.
keys will be ignored.
timer display that
The LCD screen shows the duration of the last outgoing call,
00:05' 00:05 00:05 00:05
will automatically
still displayed to
The LCD screen shows '00:00 00:00 00:00 00:00 00:00'
The LCD screen shows '00:00 00:00 00:00
00:00 00:00'.
The LCD screen shows the number as you dial (maximum of
The phone automatically dials the last number you called
When the mouthpiece is muted, the person at the other end of
number must be dialed
get another dial tone and an outside line.
LAST NUMBER REDIAL/PAUSE button immediately
pause of about 3.6 seconds will be
LAST NUMBER REDIAL/PAUSE button to insert a pause
PBX, and the PBX
The LCD screen shows 'E E E E E '.
If you try to enter more than 20 digits during programming,the