Advertisement
Configuring a wireless Internet connection ( for BDX2500 )
Repeat Blink and Interval Cycle
Cancel
I
WiFi-me
:.connectl WPS Pin
I
Delete
WiFi-me
Press ENTER to open keyboard
4. Press ENTER to activate the on-screen keyboard. Carefully enter the network
password by using the "'I
~
1
<II
1
~
to highlight the desired letter on the keyboard,
and then pressing OK. (If you make a mistake, use the backspace
lEa
key to erase
the mistake.)
4. Press "'I
~
to highlight Connect, and press OK. If the wireless network is
functioning,
~icon
and a message "Connection to XXX ...Success" will appear on
theN.
5. Press OK to close the message. The BO disc player is now connected to the
network. From now on, when you turn on the player, it will automatically connect to
the network; there is no need to repeat these steps again.
Note: If you do not see this message, the BO player was not able to connect to the
network.
b. If the SD player is connected to an Encrypted Wireless Network, a menu similar
to the following will appear:
3. Press
"'/~
to select the desired wireless network, and press OK to confirm.
a. If the SD player is connected to an Unencrypted Wireless Network, a menu
similar to the following will appear:
5. Use
"'I
~
1
<II
1
~
highlight
IJm
on the upper-right corner of the keyboard, and
press OK to remove the keyboard from the screen.
6. Use ~ to highlight Connect, and press OK. If the wireless network is functioning,~
icon and a message "Connection to XXX... Success" will appear on the N.
Y. Press OK to close the message. The BO player is now connected to the network.
From now on, when you turn on the player, it will automatically connect to the
network;there is no need to repeat these steps again.
Notes:
• If you do not see this message, the BO player was not able to connect to the network.
• If the wireless network is encrypted using an unsupported encryption (it appears in
the network list with an icon), you cannot connect to the network. You must change
the router's encryption type before proceeding.
The wireless network supports 802.11
alb 1 gin
Strong Signal
When the BO player is turned on, it will connect to
the wireless network displaying this symbol.
Typically, this is the last wireless network
connected before powering down.
The wireless network data is not encrypted.
The wireless network data is encrypted;
a
'security key' must be entered so that the BO
player can share data over the network.
The wireless network properties have been saved
in the BO player's memory.
I----:;:==~- LED1
~O
--..,.--'''::;::::::i~-
LED2
Keep Blinking (Medium Speed)
_ _ _-"'---L_K_e_e.P Blinking (High Speed)
...l
Saved
\I
Wireless Security
tr
('I
II
(6)
Wireless Protocol
o~mlil
Signal Strength
1111
L.....
L.....
.l...-N_O_S_i_g_n_al
--.J
This section describes how to configure theBO player for accessing the internet via
a WiFi connection. The procedure for connecting to a wireless network depends on
various network parameters. Read the following configuration methods to determine
which instructions to use to connect to your network.
1. Connection to the Wireless Network which you select.
a. Connecting to an Unencrypted Wireless Network
b. Connecting to an Encrypted Wireless Network
2. Connection to the Wireless Networks Using Wifi Protected Setup (WPS)*
a. Connecting to a Wireless Network Using WPS Pushbutton
b. Connecting to a Wireless Network Using WPS PIN
3. Connection to the Wireless Networks Using ManuallP Configuration
*You need update software of BOX2500 to be based on the standard of "Wifi
Protected Setup (WPS)".
The follows are showed with the screen after the software of BOX2500 was updated.
Description of the Wireless Network List Display
Choosing "Network List" in the wireless network setup menu will cause a list of available
WiFi networks to appear.
The symbols that might appear next to each listed wireless network in the network list
are as follows:
1. Connection to the Wireless Network which you select.
1. Press "'I
~
to select Wireless, then press OK to confirm.
the following screen will appear.
Network List
•
WiFi Protected Setup (WPS)
Manual
IP Settings
2. Press
"'I
~
to select Network List, then press OK. A list of existing wireless
networks near the BO player will appear (It may take several seconds for this list to
be created). For exmaple:
2. Connection to the Wireless Networks Using Wifi Protected Setup (WPS)
1. Press
"'/~
to select Wireless, then press OK to confirm.
a. If the SD player is connected to a Wireless Network Using WPS Pushbutton:
2. Press
"'/~
to select WiFi Protected Setup (WPS), then press OK.
3. Press the WPS button on the top of your router.
4. Once you see "Success" on the button at the bottom of the screen, the BO player is
connected to the router.
Note: If you do not see this message, the BO player was not able to connect to the
network. Repeat steps 1-4 again.
b. If the SD player is connected to a Wireless Network Using WPS PIN:
2. Press
"'/~
to select Network List, then press OK. A list of existing wireless
networks near the BO player will appear (It may take several seconds for this list to
be created).
3. Press "'I
~
to select the desired wireless network, and press OK to confirm.
4. Press
<II
1
~
to highlight WPS PIN, and press OK. The following screen will appear:
5. Press
<II
1
~
to highlight connection method you desire, and press OK.
6. According to displayed message, continue operating the connection.
Network List
,
~
WiFi lllrnGl
III
" lr
3. Wireless Networks Using Manual IP Configuration
..,
WiFi-me"
1. Press 1 to select Wireless, then press OK to confirm.
2. Press
"'/~
to select Manual, then press OK.
WiFi I!Irn
If!
n
Panda
3. According to displayed message, continue operating the connection.
WiFi I!Irn
II
"
n
Sliest
wiFilllm
I:
n
Office
Advertisement
