GE JB900TKWW Installation Instructions Manual
GE JB900TKWW Installation Instructions Manual

GE JB900TKWW Installation Instructions Manual

Free-standing electric ranges
Hide thumbs Also See for JB900TKWW:

Advertisement

Quick Links

Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely
and carefully.
IMPORTANT
instructions for local inspector's use.
IMPORTANT
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires basic mechanical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation
is not covered under the Warranty.
WARNING
be properly grounded.

FOR YOUR SAFETY:

WARNING
installation, switch power off at service panel
and lock the service disconnecting means to
prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to
the service panel.
31-10620
05-05 JR
— Save these
— Observe all
— This appliance must
— Before beginning the
Free-Standing
Electric Ranges
ANTI-TIP DEVICE
WARNING
of tipping, the appliance must be secured by
properly installed Anti-Tip bracket packed
with this appliance.
If the Anti-Tip device supplied with the range
does not fit this application, use the universal
Anti-Tip device WB2X7909.
If you pull the range out and away from the
wall for any reason, make sure the Anti-Tip
bracket is engaged when the range is pushed
back against the wall.
1
— To reduce the risk
WARNING
• All ranges can tip
• Injury to persons could result
• Install Anti-Tip bracket packed
with range
• See Installation Instructions

Advertisement

Table of Contents
loading

Summary of Contents for GE JB900TKWW

  • Page 1: Installation Instructions

    Installation Free-Standing Instructions Electric Ranges Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com BEFORE YOU BEGIN ANTI-TIP DEVICE Read these instructions completely WARNING — To reduce the risk and carefully. of tipping, the appliance must be secured by properly installed Anti-Tip bracket packed IMPORTANT •...
  • Page 2: Prepare To Install The Range

    Installation Instructions PREPARE TO INSTALL THE RANGE FOR YOUR SAFETY: MATERIALS YOU MAY NEED All rough-in and spacing dimensions must be met for safe use of your range. On ranges with storage drawers electricity can be disconnected at the outlet without moving Tin Snips Lag Bolts Anchor Sleeves...
  • Page 3: Prepare The Opening

    Installation Instructions PREPARE THE OPENING See illustrations for all rough-in and spacing dimensions. The range may be placed with 0” clearance (flush) at the back wall and side walls of **30” Min. the cabinet. ***6” Min. **15” Min. Acceptable electrical outlet area.
  • Page 4: Electrical Connections

    Installation Instructions ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS You must use a 3-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz CAUTION: electrical system. For personal safety, do not use an extension cord with this If the electrical service provided does not appliance.
  • Page 5: Power Cord And Strain Relief Installation

    Installation Instructions POWER CORD AND For power cord installations only (see the next step if using conduit), assemble STRAIN RELIEF INSTALLATION the strain relief in the hole. Insert the power cord through the strain relief and Remove the wire cover (on the back of tighten.
  • Page 6 Installation Instructions ELECTRICAL CONNECTIONS (CONT.) 3-WIRE POWER CORD 4-WIRE POWER CORD INSTALLATION INSTALLATION WARNING: WARNING: The neutral or ground The neutral wire of wire of the power cord must be connected the supply circuit must be connected to the to the neutral terminal located in the neutral terminal located in the lower center center of the terminal block.
  • Page 7: 3-Wire Conduit Installation

    Installation Instructions 3-WIRE CONDUIT INSTALLATION 4-WIRE CONDUIT INSTALLATION Loosen the 3 lower terminal screws from Loosen the three lower terminal screws the terminal block. Insert the center bare from the terminal block. Remove the ground wire (white/neutral) tip through the bottom screw and ground plate and retain them.
  • Page 8: Install The Range

    Installation Instructions INSTALL THE RANGE PREPARE TO LEVEL MODELS REPLACE THE WIRE COVER WITH BAKING OR WARMING Replace the wire cover on the range back DRAWERS by sliding its left edge under the retaining tabs and replacing the five screws removed Measure the height of your countertop earlier.
  • Page 9: Storage Drawer

    Installation Instructions LEVEL THE RANGE FINAL INSTALLATION CHECKLIST Install the oven shelves in the oven and position the range where it will be installed. • Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are Check for levelness by replaced.
  • Page 10 Notes...
  • Page 11 Notes...
  • Page 12 Printed in the United States...

This manual is also suitable for:

Jb910slss - profiletm 30" electric rangeJbp66wkww

Table of Contents