Advertisement
Quick Links
LoPro10
LoPr010
Low Profile Amplified Subwoofer
Low Profile Amplified Subwoofer
1.2012
1.2'12
SOUND
LABORATOR
3451 LUNAR COURT, OXNARD CA 93030
3451 LUNAR COURT, OXNARD CA 93030
PHONE: 888.38.STORM
PHONE:
FAX: 805.983.7068
FAX: 805.983.7068
TECHNICAL SUPPORT
TECHNICAL
www.soundstormlab.com
www.soundstormlab.com
STORMO
888.38.STORM
805.983.8008
805.983.8008
SUPPORT
U s e r ' s M a n u a l
User's
Manual
√
LoPro10
LoPr010
Low Profile Amplified Subwoofer
Low Profile Amplified Subwoofer
Advertisement
Related Manuals for Ssl LoPro10
Summary of Contents for Ssl LoPro10
- Page 1 LoPro10 LoPr010 Low Profile Amplified Subwoofer Low Profile Amplified Subwoofer 1.2012 1.2'12 U s e r ’ s M a n u a l User's Manual √ SOUND STORMO LABORATOR 3451 LUNAR COURT, OXNARD CA 93030 3451 LUNAR COURT, OXNARD CA 93030 PHONE: 888.38.STORM...
- Page 2 Installation precautions and quality, and will afford you Fuses years of listening pleasure. Mounting the subwoofer Thank you for making a SSL your choice for car audio Connecting the subwoofer entertainment! Front panel controls and features Rear panel controls and features...
- Page 3 What is included? Introduction The LOPROIO is a low-profile When first unpacking your new amplified subwoofer. Low enough to amplified subwoofer, please check easily fit below the seat of your car, first that the package contains all of this system offers you a quick and the items below.
- Page 4 General precautions Protection Circuitry The built-in amplifier incorporates Before installing and using your new special protection circuitry which will sscamplified subwoofer, please disable the amplifier if any of the become familiar with all the infor- following should occur: mation contained in this manual.
- Page 5 Installation precautions Mounting the subwoofer Before you drill or cut any holes, Find a suitable location in the vehicle investigate your carls layout very in which to mount the amplifier. A carefully. Take special care when you typical location is shown below: work near the gas tank, fuel lines, hydraulic lines and electrical wiring Vehicle...
- Page 6 Connecting the subwoofer Before doing any wiring, look through this manual and identify the diagrams to follow for power, input and speaker connections for your particular installation. Be sure you understand 00000 all the connections before you proceed 1. Connect the ground terminal to the closest point on the chassis of the Attaching the mounting...
- Page 7 Connecting the subwoofer Don't misuse (cont.) level control! Do not mistake the input level control 9. Power up the head unit and the for a volume control! It is designed subwoofer. Then set the volume control ONLY to match the output level of on the head unit to about 3/4 volume, your audio source to the input level and adjust the subwoofer's...
- Page 8 Front panel controls and features S WuS @ REMOT LEVEL C ONTROL PORT @ PHASE S HIFT Use this switch to help compensate Attach included remote level control to control the volume level for time alignment problems in the the subwoofer independently.
- Page 9 Rear panel controls and features pgwtN @ POWE TERMINAL O HIGH LEVEL ( speaker l evel) INPUTS If your head unit does not have RCA @ FUS outputs, you can use the speaker The fuse in the upper socket is the outputs for the audio source for the fuse which provides protection for the LOPROIO .
- Page 10 Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Most trunk or hatchback installations will require a 15-20 foot RCA cable, while pickup trucks and under-seat installations will require a 6-12 foot RCA cable. Always use a high quality cable.
- Page 11 Power Connections Connect the ground terminal to the closest point on the chassis of the vehicle. Keep this ground wire to less than 39" (100 cm) in length. Use 8 gauge (or heavier) wire. Connect the remote terminal to the remote output of the head unit using 16 gauge (or heavier) wire.
- Page 12 Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM POSSIBLE REMEDY Amplifier will not Check to make sure you have a good ground connection.
- Page 13 Specifications SSA.- 10" Amplified Subwoofer LOPROIO MODEL Maximum power 1200W Signal-to-noise ratio >90dB Frequency response 20Hz - 150Hz Input sensitivity, high level o.6V 190mV Input sensitivity, level pass filter 50Hz -150Hz Subsonic filter 20Hz - 50Hz Bass Boost O to +12dB Phase shift Selectable,...
Need help?
Do you have a question about the LoPro10 and is the answer not in the manual?
Questions and answers