Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP 8 Maintenance And Troubleshooting Manual
  1. Manuals
  2. Brands
  3. Kurzweil Manuals
  4. Synthesizer
  5. K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP...
  6. Maintenance and troubleshooting manual
Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP 8 Maintenance And Troubleshooting Manual

Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP 8 Maintenance And Troubleshooting Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Chapter 8
Maintenance and Troubleshooting

Preventive Maintenance

With a modicum of care, your K2600 will give you years of use and enjoyment. There are just a
few important points to keep in mind.
Proper installation is essential to the health and welfare of your K2600. Keyboard models should
always rest on a hard ßat surfaceÑand on its rubber feet, not on the bottom panel. Rack models
should be mounted in a standard 19-inch MIDI rack, or should rest on a hard ßat surface. In this
case it must rest on its rubber feet, and not on the bottom panel.
Never block the ventilation openings; doing so can cause overheating that will seriously damage
your K2600. To provide adequate ventilation, the rear panel should be at least four inches from
any vertical surface (for both keyboard and rack models). Try to minimize the amount of dust in
the environment.
The K2600Õs RAM backup battery, along with any PRAM, sample RAM, or ROM block options
you may install, are the only user-serviceable parts in the K2600. The only part you should ever
disassemble on your K2600 is the access panel on the bottom of the instrumentÑremoving
anything else will void your product warranty.
Cleaning Your K2600
ItÕs a good idea to remove dust from your K2600 occasionally. You may also want to remove
Þngerprints. You can clean the K2600Õs front panel with a soft damp cloth, and use a mild soap
or detergent. Never use strong cleaners or solvents, and never spray anything on the front panel
or into the ventilation holes. Any cleaners you may want to use should be applied to your
cleaning cloth; you can then carefully wipe the surfaces of the K2600.
Floppy Disk Drive Maintenance
As long as youÕre reasonably careful to keep dirt and dust out of the ßoppy disk drive, you
shouldnÕt have any problems. If, however, you start to experience errors or failures in loading or
saving, it may be due to dirt in the ßoppy drive mechanism. See your dealer for information
regarding products and techniques for ßoppy drive cleaning.
Maintenance and Troubleshooting
Preventive Maintenance
8-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP 8 and is the answer not in the manual?

Questions and answers

Related Manuals for Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP 8

Summary of Contents for Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP 8

  • Page 1: Chapter 8 Maintenance And Troubleshooting

    Maintenance and Troubleshooting Preventive Maintenance Chapter 8 Maintenance and Troubleshooting Preventive Maintenance With a modicum of care, your K2600 will give you years of use and enjoyment. There are just a few important points to keep in mind. Proper installation is essential to the health and welfare of your K2600. Keyboard models should always rest on a hard ßat surfaceÑand on its rubber feet, not on the bottom panel.

  • Page 2: Battery Replacement

    Maintenance and Troubleshooting Battery Replacement Battery Replacement The K2600 uses a 3-volt lithium coin-cell battery (CR2032) for program RAM backup (sample RAM is not battery-backed). Unlike a typical alkaline batteryÑwhose voltage output declines over the life of the batteryÑa lithium cell maintains a stable voltage until itÕs almost out of power.

  • Page 3: Scanner Diagnostics

    Maintenance and Troubleshooting Scanner Diagnostics 10. Replace the access panel and loosely install the screws, starting with those closest to the hinge (the back) of the access panel. When the screws are loosely in place, tighten them all. Note to K2500 owners : On 2500-series instruments, the LEDs on the front panel ßash three times when battery voltage is low.

  • Page 4: Ground Hum

    Maintenance and Troubleshooting Maximizing Music and Minimizing Noise in MIDI mode and setting the OutGain parameter to the desired level (in 6dB steps). For songs that use multiple MIDI channels, youÕll need to do this for each channel. Alternatively you can increase the volume of a single program by going to the OUTPUT page in the Program Editor and setting the Gain parameter to the desired level, again in 6dB steps.

  • Page 5: Power Problems And Solutions

    Maintenance and Troubleshooting Power Problems and Solutions Power Problems and Solutions The K2600 is quite tolerant of voltage ßuctuations, noise, and transients in the AC power it receives. The input line Þlter and grounded power cable will protect against even large amounts of noise from motors and the like while the built-in Þlter coupled with the fuse will protect against all but the largest transients.

  • Page 6: Other Possible Problems

    Maintenance and Troubleshooting Troubleshooting Lower the volume of your sound system, and turn the K2600 off, then on again (this is called a power cycle). Press the +/- , 0 , and Clear buttons (on the alphanumeric buttonpad) at the same time. This is called a soft reset.
  • Page 7 Maintenance and Troubleshooting Troubleshooting Programs, Setups, Songs, or Other Objects Are Missing Battery has run down or has been disconnected. If the battery has failed, the message ÒBattery voltage is low - X.X voltsÓ (where X.X is less than 3.0) will appear in the display on powerup. All user data will be permanently lost if this occurs.

This manual is also suitable for:

K2600

Table of Contents