Page 1
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Page 2
No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact...
Page 3
CONTENTS CONTENTS Page content Page TITLE PAGE INTRODUCTION REVISION HISTORY.. UNDERSTANDING THIS MANUAL COPYRIGHT NOTICE CONTENTS CONTENTS GUARANTEE GUARANTEE INTRODUCTION SCOPE SPECIFICATION HANDLING & STORAGE HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL 6-7A SPECIFIC SAFETY INSTRUCTIONS PUMP CONNECTION TO THE POWER...
Page 4
Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the 12 month period. Please note that this guarantee...
Page 5
INTRODUCTION 4.1 SCOPE This machine is designed as a surface mounting pump suitable for domestic water and gardening applications. Any other application is considered mis-use. 4.2 SPECIFICATION Stock 56227 Part SPIOO/4 Motor: Rated voltage 230V- Rated frequency 50Hz Rated input .
Page 6
HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS PRODUCE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully.
Page 7
HEALTH & SAFETY INFORMATION Wear personal protective equipment (PPE). Dust, noise, vibration and swarf can all be dangerous if not suitably protected against. If the work involving the power tool creates dust or fumes; wear a dust mask. Vibration to the hand, caused by operating some tools for longer periods must be protected against.
Page 8
6. The float switch fitted to this pump is not suitable for continuous use as an on/off switch. IMPORTANT: PUMP RETURNED DRAPER TOOLS UNDER WARRANTY MUST CLEAN. IF A PUMP IS RECEIVED THAT IS NOT, OR HAS NOT BEEN CLEANED, IT WILL BE...
Page 10
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the pump.
Page 11
ASSEMBLY CONNECT HOSES- FIGS. 1 - 2 FIG.I NOTE: Remove the plug from the power supply before carrying out adjustment, servicing or maintenance. NOTE: This machine will function without of a solid wall suction hose kit. Connect the suction hose @ into the suction inlet Fig.1 For suction hose see optional...
Page 12
PUMP OPERATION 9.1 PUMP OPERATION- FIGS. 3 - 4 FIG.3 Before operating the pump for the first time, it should be primed with water through the suction inlet O, the filling operation must be carried out very slowly. Ensure that the water level is to the maximum.
Page 14
MAINTENANCE 11.1 MAINTENANCE The pump is completely maintenance free. If the pump becomes clogged, you should clean it out by running clean water through it. While the water is running through, start up the pump several times for approximately 2-3 seconds. This operation should remove any obstruction When there is a danger of cold or freezing...
Page 15
EXPLANATION OF SYMBOLS 12.1 EXPLANATION OF SYMBOLS Warning! Read instruction manual Warning! Disable the machine before attempting to maintain WE-EE Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish...
Page 16
DISPOSAL 13.1 DISPOSAL At the end of the machine's working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. Contact your local authority for details of collection schemes in your area. In all circumstances: •...
Page 18
E-mail: sales@drapertools.com Sales Fax: (023) 8049 4209 General Enquiries: (023) 8026 6355 Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area. YOUR DRAPER STOCKIST KCKC191...
Need help?
Do you have a question about the SP100/4 and is the answer not in the manual?
Questions and answers