Related Manuals for Cameo ROOT PAR BATTERY
Summary of Contents for Cameo ROOT PAR BATTERY
- Page 1 USER´S MANUAL BEDIENUNGSANLEITUNG MANUEL D´UTILISATION MANUAL DE USUARIO INSTRUKCJA OBSŁUGI MANUALE D´USO RGBW ROOT PAR BATTERY ® 5 × 4 W RGBW LED PAR SPOTLIGHT CLROOTPARBAT...
- Page 2 CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ / CONTENUTO ENGLISH ESPAÑOL SAFETY INFORMATION MEDIDAS DE SEGURIDAD INTRODUCTION INTRODUCCIÓN CONNECTIONS, OPERATING AND DISPLAY ELEMENTS CONEXIONES, ELEMENTOS DE MANEJO Y ELEMENTOS OPERATION DE VISUALIZACIÓN IR REMOTE CONTROL (OPTIONAL) FUNCIONAMIENTO INSTALLATION AND MOUNTNG MANDO A DISTANCIA POR INFRARROJOS (OPCIONAL) DMX TECHNOLOGY INSTALACIÓN Y MONTAJE...
-
Page 3: Intended Use
This device was developed and produced under the highest standards of quality in order to ensure smooth operation for many years. Please read these operating instructions carefully so that you can use your new Cameo Light product quickly and optimally. You can find more information on Cameo Light on our website WWW.CAMEOLIGHT.COM. -
Page 4: Battery Safety
32. The device may only be installed when it carries no voltage (separate the power plug from the power supply). 33. Dust and other debris within the device may damage it. The device should be serviced or cleaned regularly by qualified specialists depending on the environmental conditions (dust, nicotine, smoke, etc.) in order to avoid overheating. - Page 5 CHARGING THE BATTERY, OPERATING, AND STORING THE SPOTLIGHT • Connect the spotlight to the power supply in order to charge the internal battery. The battery is charged both when it is switched on and when the spotlight is switched off. •...
-
Page 6: Connections, Operating And Display Elements
POWER OUT White Power Twist power output socket to supply power to additional Cameo spotlights (max. 8 A). DMX IN Male 3-pin XLR connector to connect a DMX control device (e.g., DMX console). -
Page 7: Control Buttons
CONTROL BUTTONS MENU – you can access the options menu by pressing MENU. Pressing it again will return you to the main display. If you press MENU without having first pressed ENTER to confirm a value or status change, the previously confirmed value or status shall be restored. ENTER –... -
Page 8: Operation
NOTES • After the spotlight is switched on, “Welcome to Cameo,” the model name, and the software version are shown one after the other on the display during the start-up process. Once the process is complete, the spotlight is ready for use and resumes whichever mode was most recently activated. -
Page 9: Setting Dmx Mode
SETTING DMX MODE You can access the main menu by pressing MENU. Using the and buttons, now select the DMX Mode menu option and press ENTER to confirm your selection. Use and again to select the desired DMX mode and press ENTER to confirm your selection. Press the MENU once (1×) to return to the main screen. - Page 10 Spotlight(group) 0 Spotlight(group) 1 Spotlight(group) 2 Spotlight(group) 3 Spotlight(group) 4 Spotlight(group) 5 No delay 0.5 s delay 1 s delay 1.5 s delay 2 s delay 2.5 s delay -------Delay------- -------Delay------- -------Delay------- -------Delay------- -------Delay------- -------Delay------- Controller Group Group Group Group Group Group DMX Delay...
- Page 11 STANDALONE MODE STATIC The standalone mode static allows the dimmer, strobe, R, G, B and W values to be set directly on the device, with values between 000 and 255, in a similar way to with a DMX controller. In this way, an individual scene can be created without an additional DMX controller. Starting from the main display, press MENU to enter the main menu.
- Page 12 LOOP STAND-ALONE MODE The stand-alone Loop mode allows up to four different color change programs to be individually designed, saved, and reproduced. Bright- ness, step time, fade time, and delay (signal delay) can be set separately. Starting from the main display, press MENU to go to the main menu. Using the and buttons, select the Stand Alone menu option and press ENTER to confirm your selection.
-
Page 13: Slave Mode
SLAVE MODE Standard Slave mode: Starting from the main display, press MENU to go to the main menu. Using the and buttons, now select the Slave menu option, press ENTER to confirm your selection, then select Slave Group 0, and press enter once again to confirm. Connect the slave and master unit (same model, same software version) using a DMX cable, and activate one of the stand-alone modes on the master unit (Auto, Static, Color Preset, User Color, Loop). - Page 14 Settings Disp Rev = Rotates display Display does not rotate Display rotates 180° (e.g., for overhead instal- lation) Disp Back = Display backlight Deactivates after approx. 30 seconds of inactivity Permanently on Sig Fail Operating status if DMX Hold Last command is held signal is lost Master/ Black Activates blackout...
-
Page 15: Ir Remote Control (Optional)
SYSTEM INFORMATION (System Info) Starting from the main display, press MENU to go to the main menu. Using and , now select the System Info menu option and press EENTER to confirm your selection. --------Menu------- DMX Address DMX Mode DMX Delay Stand Alone Slave... - Page 16 FL (Flash/Strobe) Speed setting for the strobe effect in 6 steps. Step 1 deactivates the strobe effect, step 2 produces a slow frequency followed by steps 3 to 5. Step 6 produces the fastest flash frequency. The strobe effect can only be used in RGBW color mixing mode. R / G / B / W Individual color mixes can be created using these 4 buttons.
-
Page 17: Setup And Installation
SETUP AND INSTALLATION Thanks to the convenient twin mounting bracket, the spotlight can be placed in a suitable location on a flat surface. Install on a crossbeam using a traverse clamp that is attached to the mounting bracket (A). Suitable traverse clamps are available as needed. Ensure that the connections are tight and secure the spotlight to the fixing eyelet on the back of the spotlight using a suitable safety eyebolt. -
Page 18: Dmx Technology
DMX TECHNOLOGY DMX-512 DMX (Digital Multiplex) is the designation for a universal transmission protocol for communications between corresponding devices and controllers. A DMX controller sends DMX data to the connected DMX device(s). The DMX data is always transmitted as a serial data stream that is forwarded from one connected device to the next via the "DMX IN"... -
Page 19: Technical Data
TECHNICAL DATA Article number: CLROOTPARBAT Product type: LED battery spotlight Type: PAR spotlight Color spectrum: RGBW Number of LEDs: LED type: LED PWM frequency: 650 Hz, 1530 Hz, 2150 Hz, 4000 Hz (adjustable) Beam angle (half peak angle): 33° (20°) DMX input: 3-pin male DMX output:... -
Page 20: Manufacturer's Declarations
MANUFACTURER´S DECLARATIONS MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY You can find our current warranty conditions and limitations of liability at: https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS- DECLARATIONS_CAMEO.pdf. To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Anspach / Email: Info@adamhall.com / +49 (0)6081 / 9419-0. CORRECT DISPOSAL OF THIS PRODUCT (valid in the European Union and other European countries with a differentiated waste collection system) This symbol on the product, or on its documents indicates that the device may not be treated as household waste. - Page 21 DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX / CONTROL DMX / STEROWANIE DMX / CONTROLLO DMX The DMX Delay channel is only activated in DMX modes when menu item DMX Delay is set to by DMX? Yes. Der Kanal DMX Delay ist in den DMX-Modi nur aktiviert, wenn im Menüpunkt DMX Delay unter by DMX? Yes eingestellt ist. Le décalage DMX de canal n’est activé...
- Page 22 5-Channel Mode 1 Function Values Sub-Group Dimmer 0% to 100% Dimmer Strobe open Strobe closed Ramp up/down, slow -> fast Ramp up/down random, slow->fast Ramp up, slow -> fast Ramp up random, slow -> fast Strobe functions Multifunctional Ramp down, slow -> fast Strobe Ramp down random, slow ->...
- Page 23 5-Channel Mode 2 Function Values Sub-Group 0% to 100% Green Green 0% to 100% Blue 0% to 100% Blue White 0% to 100% White No Delay DMX Delay DMX Delay 0,1s -> 2,0s 6-Channel Mode Function Values Sub-Group Dimmer 0% to 100% Dimmer Strobe open Strobe...
- Page 24 Strobe open Strobe Strobe Strobe slow -> fast <1Hz - 20Hz 0% to 100% Green Green 0% to 100% Blue 0% to 100% Blue White 0% to 100% White No Delay DMX Delay DMX Delay 0,1s -> 2,0s 10-Channel Mode Function Values Sub-Group...
- Page 25 User Color_1 Color Presets User Color_2 & Color Jumping & Color Fading User Color_3 Color Preset & User Colors User Color_4 (override RGBW) no function Sound Sound Control off (triggers Strobe, Color Jump- Sound Sound Control on, mic sensitivity low -> high ing &...
- Page 26 CAMEOLIGHT.COM Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany Phone: +49 6081 9419-0 | adamhall.com REV: 02...
Need help?
Do you have a question about the ROOT PAR BATTERY and is the answer not in the manual?
Questions and answers