Download Print this page
Homematic IP HmIPW-WRC6 Installation And Operating Manual
Homematic IP HmIPW-WRC6 Installation And Operating Manual

Homematic IP HmIPW-WRC6 Installation And Operating Manual

Wired wall-mount remote control – 6 channels

Advertisement

Quick Links

Wired Wall-mount Remote Control – 6
channels
HmIPW-WRC6, HmIPW-WRC6-A
Installation and Operating Manual
EN

Advertisement

loading
Need help?

Need help?

Do you have a question about the HmIPW-WRC6 and is the answer not in the manual?

Questions and answers

Summary of Contents for Homematic IP HmIPW-WRC6

  • Page 1 Wired Wall-mount Remote Control – 6 channels HmIPW-WRC6, HmIPW-WRC6-A Installation and Operating Manual...
  • Page 2 Table of contents Table of contents 1 Table of contents....................3 2 Information about this manual................. 3 3 Hazard information....................3 4 General system information................5 5 Function and device overview................5 6 Start-up........................5 6.1 Installation instructions....................6 6.2 Installation........................7 6.3 Installation in multiple combinations..............8 6.4 Pairing with a control unit..................8 7 Operation.......................
  • Page 3 Do not use any Read this manual carefully before begin- detergents containing solvents for ning operation with your Homematic IP cleaning purposes. Wired device. Keep the manual for later consultation. If you hand the device over...
  • Page 4 Hazard information The device is intended for operation on the Homematic IP Wired Bus on- ly. The Homematic IP Wired Bus is a SELV power circuit. The mains voltage for the building installation and the Homematic IP Wired Bus must be routed separately. Com-...
  • Page 5 Operation requires connec- as to integrate it into existing switch se- tion to a Homematic IP Wired Access ries from leading manufacturers. Point. For more information on the sys- tem requirements and installation plan-...
  • Page 6 Start-up Installation instructions Read this section completely before starting installation. Make a note of the device number (SGTIN) and the installation location of the device before installation to make it easier to identify the device later. The device number can also be found on the enclosed QR code Figure 4 sticker.
  • Page 7 Homematic IP conditions; Wired Bus. • IP protection types; • Connect the Homematic IP Wired • Installation of electrical installation Bus to the bus port. Press the or- material; ange operating button to connect •...
  • Page 8 Wired de- vices in the system. Homematic IP Figure 7 Further information on this is to be • Switch the Homematic IP Wired Bus found in the operating manual for on to activate pairing mode of the the Wired Access Point..
  • Page 9 Start-up • Open the Homematic IP app. If the device LED lights up red to, please try again Flash codes, • Tap on …More in the homescreen. page • Tap on Pair device. • Connect the power supply. • Then follow the instructions in the Homematic IP App.
  • Page 10 Troubleshooting vate/deactivate Eco mode or raise/ lower shutters. • Assign channels: Assign the individ- ual buttons and LEDs to the desired rooms or solutions. 8 Troubleshooting Command not confirmed If at least one receiver does not confirm a command, the LED lights up red at the end of the failed transmission.
  • Page 11 Troubleshooting Flash codes Flash code Meaning Solution 1x orange and 1x green Test display You can continue once light (after switching on the test display has the Wired Bus) stopped. Short orange flashes Pairing mode active Enter the last four dig- (every 10 s) its of the device number (SGTIN) in your app, or...
  • Page 12 Restoring factory settings 9 Restoring factory settings 11 Disposal The factory settings of the device This symbol means that the device can be restored. If the device is must not be disposed of as house- paired with a Central Control Unit, hold waste, general waste, or in a the configurations are automatically yellow bin or a yellow sack.
  • Page 13 Technical specifications 12 Technical specifications Short description HmIPW-WRC6, HmIPW-WRC6-A Supply voltage 24 VDC, ±5 %, SELV Protection class Degree of protection IP20 Ambient temperature -5 - +40°C Weight 68 g Dimensions without frame (W x H x D) 55 x 55 x 40 mm...
  • Page 14 Free download of the Homematic IP app! Bevollmächtigter des Herstellers: Manufacturer’s authorised representative: eQ-3 AG Maiburger Straße 29 26789 Leer / GERMANY www.eQ-3.de...

This manual is also suitable for:

Hmipw-wrc6-a