Advertisement
550A UNDER BENCH
IMPORTANT INSTRUCTIONS
HANDLER MANUFACTURING, LLC
159 GRASSY PLAIN STREET
612 North Ave East, Westfield, NJ 07090
BETHEL, CT 06801 USA
Ph: (908) 233-7796 Fax: (908) 233-7340 800-274-2635 E-Mail:
MANUFACTURING, LLC
PORTA - VAC
DO NOT DISCARD
Over Ninety-Five Years of Quality Manufacturing and Service...
908-233-7796
info@handlermfg.com
www.handlermfg.com
Web Site: www.handlermfg.com
Info@handlermfg.com
Advertisement
Table of Contents
Related Manuals for Handler 550A UNDER BENCH PORTA - VAC
Summary of Contents for Handler 550A UNDER BENCH PORTA - VAC
- Page 1 MANUFACTURING, LLC 550A UNDER BENCH PORTA - VAC IMPORTANT INSTRUCTIONS DO NOT DISCARD 908-233-7796 HANDLER MANUFACTURING, LLC Over Ninety-Five Years of Quality Manufacturing and Service… info@handlermfg.com 159 GRASSY PLAIN STREET 612 North Ave East, Westfield, NJ 07090 www.handlermfg.com BETHEL, CT 06801 USA Ph: (908) 233-7796 ...
-
Page 2: Safety Instructions
MANUFACTURING, LLC SAFETY INSTRUCTIONS WARNING FOR YOUR SAFETY: READ INSTRUCTIONS BEFORE OPERATING TOOL WEAR EYE PROTECTION! Over Ninety-Five Years of Quality Manufacturing and Service… 612 North Ave East, Westfield, NJ 07090 Ph: (908) 233-7796 Fax: (908) 233-7340 800-274-2635 E-Mail: ... - Page 3 Unpack your Dust Collector and inspect it. Should damage have occurred in transit, contact the freight forwarder immediately. Note on the shipping receipt any visible damage to the container and the contents. DO NOT contact Handler Manufacturing as the damage must be claimed by the receiver of merchandise – not the shipper.
-
Page 4: Maintenance
MANUFACTURING, LLC Connect the electrical cordset for the foot switch into the proper receptacle on the front of the 550A . Connect the electrical cordset which brings (Fig. 2) power to the unit into proper receptacle on the front of the unit. Plug the 550A’s cordset into a 115Volt (GFI) grounded outlet ONLY. - Page 5 Should you find that the filter bag fills quickly and must be replaced weekly, biweekly or more quickly, we suggest you may wish to look into a larger dust collector. Handler manufactures a full line of dust collectors and central systems built for continuous use in dental labs, jewelry facilities and industrial facilities.
- Page 6 MANUFACTURING, LLC TO CHANGE OR CHECK MOTOR BRUSHES UNPLUG UNIT FROM ELECTRICAL SOURCE BEFORE WORKING ON BRUSHES 1) Loosen the two screws on each side of the brass strap that is holding down the motor brush, about ½ way out (Fig.
- Page 7 P550A-GSK AVAILABLE OPTIONS FOR CONNECTION TO 550A PORTA-VAC Handler manufactures a full line of bench top hoods, fish mouths and in drawer suction trays for you to choose from. The following combinations can be connected to your 550A by following instructions on page 7.
- Page 8 CONNECTING ACCESSORIES TO YOUR 550A CONNECTING 86D-LA or 86RHL-LA : To connect to a Handler aluminum or resin Splash Hood you will need to purchase a foam gasket for the flexible hose, part number P550A-GSK. Please follow these instructions on installing the gasket: - Make sure the surface of the rigid end of the hose is clean and dry.
- Page 9 908-233-7796 HANDLER MANUFACTURING, LLC info@handlermfg.com 159 GRASSY PLAIN STREET www.handlermfg.com BETHEL, CT 06801 USA...
- Page 10 The warranty covers manufacturer defects in workmanship. Shipping costs are not covered by the warranty. During the life of this warranty, HANDLER will repair or replace (at HANDLER’s option), free of charge F.O.B. its plant, any defective part or assembly, if such defect occurred during normal service and was not due to apparent misuse, abuse, or accident.
Need help?
Do you have a question about the 550A UNDER BENCH PORTA - VAC and is the answer not in the manual?
Questions and answers